GREAT PLAINS 6321UC Guía

FIELDADJUSTMENTGUIDE

Document #TLUS400C-0001A

1 of 3

Document # TLUS400C-0001A

Tillage

Ultra-Chisel

Proper servicing and adjustment is the key to the long life of all farm equipment. With careful and

systematic inspection of equipment, costly maintenance, time and repair can be avoided. The fol-

lowing information will assist with recommended servicing and adjustments:

48649

Models Affected:6321UC, 6323UC, 6327UC, 6329UC, 6330UC, 6332UC, 6536UC, 6538UC,

6542UC, 6544UC

Date: December 1, 2014

General Information

Document #TLUS400C-0001A 2 of 3

Unfolding The Implement:

1) Be aware of the vertical and horizontal clearances needed

to unfold the implement.

2) Remove the transport wing pins and store them in their des-

ignated spots.

3) Put the track in Park and slowly begin to unfold the imple-

ment while watching for any signs of leaks or loose fittings.

4) Continue unfolding until both wings are fully extended and

level on the ground.

5) Set the tractor remote to Neutral to lock the wings.

48649

Folding The Implement:

1) Move the implement to level ground and be aware of the

vertical clearance needed to fold the implement.

2) Put the track in park and slowly begin to fold the wings.

3) Continue folding until the wings rest within the transport

nests.

4) Install the transport wing pins before transport the imple-

ment.

48650

Center And Wing Leveling: Leveling of the machine should

be done on a smooth level surface. Lower the implement so

that the sweeps on the center frame are 1-2” off the ground.

Wing Leveling:

1) Set the 3-section and 5-section inner and outer wings to

match the depth of the center section. This can be done by

adjusting the rear wing turnbuckle on (1) each wing.

2) Loosen the jam nut (2) and begin adjusting the turnbuckle

(1). Lengthen the turnbuckle tube to run deeper and shorten

the turnbuckle to run shallower.

3) Tighten the jam nut (2) back against the turnbuckle tube to

hold the adjustments in place. Note: In some conditions the

wings will need to be set slightly lower than the center section,

as the center section may ten to run deeper behind the tractor

tires.

48651

Center And Wing Gauge Wheel Adjustments:

1) Loosen the jam nut (3) and adjust the turnbuckle (4) on the

gauge wheels to level it from front to back. Lengthen the turn-

buckle to bring the front up or shorten the turnbuckle to bring

the front down.

2) Level the machine with the front row shanks just slightly

deeper or lower than the back.

3) Re-tighten the jam nut (3) back against the turnbuckle.

Document #TLUS400C-0001A

3 of 3

Hydraulic Depth Stop: The hydraulic depth stop will maintain

constant depth every time the implement is raised and low-

ered. Adjust the per the following:

1) Simply screw the depth stop handle in to run the implement

shallower. Unscrewing the depth stop handle will allow for the

implement to run deeper. One full turn of the depth stop handle

is equivalent to 1/4” of working depth. Note: If after setting the

depth stop, the detent on the tractor kicks out before the stop

contacts the button of the depth stop, slow the tractor hydraulic

flow down. Do not adjust the rebound valve without first con-

tacting the factory service representative.

48654

Rear Attachment Settings

Spike Drag Settings: On the spike drag, start with 5 links

hanging from the chain in drag arm bottom slot. (This is a start-

ing point for worst conditions). The cleaner the ground, the

shorter the pull chain may be pulled up.

On the spike drag, one of the links in the first row of angles is

turned over to allow the trash to start flowing through the drag

easier. Note: Make sure that the drag is never pulling off of the

hang chains, if so, shorten the pull chains.

Heavy Coil Tine Settings: The factory setting will have the

spring pre-set at 3-3 1/2” of bolt left to adjust. To adjust the

down pressure:

1) Loosen the jam nut (5) and screw the spring bolt (6) in to

apply more down pressure on the drag, or adjust the bolt out to

apply less down pressure.

2)Re-tighten the jam nut (5) to secure all adjustments.

48655

48653

3) To change the angle of the coil tine, rotate the locking pin (7)

and move the adjustment lever (8) forward or backwards. Mov-

ing the lever towards the rear of the machine makes the drag

more aggressive while moving the lever towards the front of

the machine will allow residue to flow through easier.

The adjustment lever has four positions and will change the

coil tines several degrees.

4) Rotate the locking pin (7) back to its engaged position when

the desired angle is achieved.

48656

Reel Settings: If a reel is added to the back of the Ultra-

Chisel, adjust the amount of down pressure by either shorten-

ing the springs for less pressure or lengthening them for more

pressure:

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Maquinaria agrícola de GREAT PLAINS

GREAT PLAINS

GREAT PLAINS 3P1006NT Guía

GREAT PLAINS

GREAT PLAINS CTA4000 Manual de usuario

GREAT PLAINS

GREAT PLAINS 3S-4000HD Manual de usuario

GREAT PLAINS

GREAT PLAINS 1510P Manual de usuario

GREAT PLAINS

GREAT PLAINS MC5109 Max-Chisel Manual de usuario

GREAT PLAINS

GREAT PLAINS Qualidisc HS2200-13 Manual de usuario

GREAT PLAINS

GREAT PLAINS 5109 Manual de usuario

GREAT PLAINS

GREAT PLAINS PL5700 Manual de usuario

GREAT PLAINS

GREAT PLAINS PL5500-0830 Manual de usuario

GREAT PLAINS

GREAT PLAINS NTA607HD Manual de usuario

GREAT PLAINS

GREAT PLAINS PL5500 Manual de usuario

GREAT PLAINS

GREAT PLAINS Turbo Max 3500TM Manual de usuario

GREAT PLAINS

GREAT PLAINS 3P1006NT Manual de usuario

GREAT PLAINS

GREAT PLAINS YP925TD Manual de usuario

GREAT PLAINS

GREAT PLAINS 8323 Manual de usuario

GREAT PLAINS

GREAT PLAINS Turbo Max 3.0M Manual de usuario

GREAT PLAINS

GREAT PLAINS BD7600 Manual de usuario

GREAT PLAINS

GREAT PLAINS Turbo-Max 6.0M Manual de usuario

GREAT PLAINS

GREAT PLAINS NTA607HD Manual de usuario

GREAT PLAINS

GREAT PLAINS 2400TM Guía

GREAT PLAINS

GREAT PLAINS Nutri-Pro NP40A Manual de usuario

GREAT PLAINS

GREAT PLAINS 1510HDP Manual de usuario

GREAT PLAINS

GREAT PLAINS BD7600 Manual de usuario

GREAT PLAINS

GREAT PLAINS Nutri-Pro NP30A Manual de usuario

Manuales populares de Maquinaria agrícola de otras marcas

GSi

GSi PNEG-2314 Manual de usuario

Checchi & Magli

Checchi & Magli TEXDRIVE Manual de usuario

Amazone

Amazone Cenius 4003-2TX Manual de usuario

MASSEY FERGUSON

MASSEY FERGUSON MF 9313S Manual de usuario

Cima

Cima BLITZ Instrucciones de funcionamiento y mantenimiento

Amazone

Amazone CombiDisc 3000 Instrucciones de instalación

HE-VA

HE-VA Disc-Roller XL Contour Manual de usuario

AGT

AGT AGT-SSFM Manual de usuario

Milestone

Milestone 72-84 Manual de usuario

KUHN

KUHN Hector 3000 Manual de usuario

Krone

Krone X-Disc 6200 Manual de usuario

Eliet

Eliet DZC450 Manual de usuario

Taarup

Taarup BIO+ B4000 Manual de usuario

Garland

Garland SHAKER 310 DPG Manual de usuario

stable comfort

stable comfort StableWall System Manual de usuario

Raven

Raven AccuBoom Manual de usuario

International

International 710 Manual de usuario

Ashland

Ashland HDW-3217-14 Manual de usuario