GREAT PLAINS 1205NT Manual de usuario

Cover illustration may show optional equipment not supplied with standard unit.

Read the operator’s manual entirely. When you see this symbol, the subsequent

instructions and warnings are serious - follow without exception. Your life and

the lives of others depend on it!

Manufacturing, Inc.

14001

Predelivery Manual

1205NT

End-Wheel, No-Till Drill

150-131Q

11/10/99

Table of Contents

Great Plains Manufacturing, Inc. provides this publication “as is” without warranty of any kind, either expressed or implied. While every precaution has been taken in the

preparationofthismanual,Great PlainsManufacturing,Inc.assumesnoresponsibility forerrorsoromissions.Neitherisanyliability assumedfordamagesresultingfrom

theuse of theinformation containedherein. Great PlainsManufacturing,Inc. reserves the right toreviseand improveitsproducts asit sees fit.This publicationdescribes

the state of this product at the time of its publication, and may not reflect the product in the future.

Great Plains Manufacturing, Incorporated Trademarks

The following are trademarks of Great Plains Mfg., Inc.: Application Systems, Ausherman, Land Pride, Great Plains

All other brands and product names are trademarks or registered trademarks of their respective holders.

Printed in the United States of America.

150-131Q 3/24/06

Important Safety Information. . . . . . . . . . . . . 1

Safety at All Times . . . . . . . . . . . . . . . . . . . 6

Description of Unit . . . . . . . . . . . . . . . . . . . 7

Intended Usage . . . . . . . . . . . . . . . . . . 7

Models Covered. . . . . . . . . . . . . . . . . . 7

Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Using This Manual . . . . . . . . . . . . . . . . . . . 8

Deﬁnitions . . . . . . . . . . . . . . . . . . . . . . 8

Assembly and Setup Assistance . . . . . . . . 8

Tools Required . . . . . . . . . . . . . . . . . . . . . . 9

Pre-Assembly Checklist . . . . . . . . . . . . . . . 9

Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Tongue Assembly . . . . . . . . . . . . . . . . . . . 10

Hydraulic Attachment . . . . . . . . . . . . . . . . 11

Wiring Attachment . . . . . . . . . . . . . . . . . . 11

Clutch Linkage . . . . . . . . . . . . . . . . . . . . . 11

Hitching Tractor to Drill . . . . . . . . . . . . . . . 12

Hitch Assembly . . . . . . . . . . . . . . . . . 12

Hitch Height . . . . . . . . . . . . . . . . . . . . 12

Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Hitching to Tractor . . . . . . . . . . . . . . . 13

Hydraulic Hose Hookup . . . . . . . . . . . . . . 14

Bleeding Hydraulics . . . . . . . . . . . . . . . . . 14

Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Torque Values Chart. . . . . . . . . . . . . . . . . 16

Tire Inﬂation Chart . . . . . . . . . . . . . . . . . . 17

3/24/06 150-131Q

Important Safety Information

Look for Safety Symbol

The SAFETY ALERT SYMBOL indicates there is

apotential hazardto personalsafetyinvolvedand

extra safety precaution must be taken. When you

see this symbol, be alert and carefully read the

message that follows it. In addition to design and

conﬁguration of equipment, hazard control and

accident prevention are dependent upon the

awareness, concern, prudence and proper train-

ing of personnel involved in the operation,

transport, maintenance and storage of

equipment.

Be Aware of Signal Words

Signal words designate a degree or level of haz-

ard seriousness.

DANGER indicates an imminently hazardous sit-

uation which, if not avoided, will result in death or

serious injury. This signal word is limited to the

most extreme situations, typically for machine

components that, for functional purposes, cannot

be guarded.

WARNING indicates a potentially hazardous situ-

ationwhich,if notavoided,couldresultindeath or

serious injury, and includes hazards that are ex-

posed when guards are removed. It may also be

used to alert against unsafe practices.

CAUTION indicates a potentially hazardous situ-

ation which, if not avoided, may result in minor or

moderate injury. It may also be used to alert

against unsafe practices. !CAUTION

WARNING

!DANGER

1205NT

150-131Q 3/24/06

Be Familiar with Safety Decals

▲Read and understand “Safety Decals,” page 4,

thoroughly.

▲Read all instructions noted on the decals.

Keep Riders Off Machinery

Riders obstruct the operator’s view. Riders could

be struck by foreign objects or thrown from the

machine.

▲Never allow children to operate equipment.

▲Keep all bystanders away from machine dur-

ing operation.

Shutdown and Storage

▲Lower drill, put tractor in park, turn off engine,

and remove the key.

▲Secure drill using blocks and supports pro-

vided.

▲Detach and store drill in an area where chil-

dren normally do not play.

Use Safety Lights and Devices

Slow-moving tractors and towed implements can

create a hazard when driven on public roads.

They are difﬁcult to see, especially at night.

▲Use ﬂashing warning lights and turn signals

whenever driving on public roads.

▲Use lights and devices provided with imple-

ment.

OFF

3/24/06 150-131Q

Important Safety Information

Transport Machinery Safely

Maximum transport speed for implement is 20

mph. Some rough terrains require a slower

speed.Suddenbrakingcancauseatowedloadto

swerve and upset.

▲Do not exceed 20 mph. Never travel at a

speed which does not allow adequate control

of steering and stopping. Reduce speed if

towed load is not equipped with brakes.

▲Comply with state and local laws.

▲Do not tow an implement that, when fully

loaded, weighs more than 1.5 times the weight

of towing vehicle.

▲Carry reﬂectors or ﬂags to mark drill in case of

breakdown on the road.

▲Keep clear of overhead power lines and other

obstructions when transporting. Refer to trans-

port dimensions under “Speciﬁcations and

Capacities,” in your operator’s manual.

Avoid High Pressure Fluids

Escaping ﬂuid under pressure can penetrate the

skin, causing serious injury.

▲Avoid the hazard by relieving pressure before

disconnecting hydraulic lines.

▲Use a piece of paper or cardboard, NOT

BODY PARTS, to check for suspected leaks.

▲Wear protective gloves and safety glasses or

goggles when working with hydraulic systems.

▲If an accident occurs, see a doctor immedi-

ately. Any ﬂuid injected into the skin must be

surgically removed within a few hours or gan-

grene may result.

1205NT

150-131Q 3/24/06

Practice Safe Maintenance

▲Understand procedure before doing work. Use

proper tools and equipment. Refer to this man-

ual for additional information.

▲Work in a clean, dry area.

▲Lower the drill, put tractor in park, turn off

engine, and remove key before performing

maintenance.

▲Make sure all moving parts have stopped and

all system pressure is relieved.

▲Allow drill to cool completely.

▲Disconnect battery ground cable (-) before

servicing or adjusting electrical systems or

before welding on drill.

▲Inspect all parts. Make sure parts are in good

condition and installed properly.

▲Remove buildup of grease, oil or debris.

▲Remove all tools and unused parts from drill

before operation.

Prepare for Emergencies

▲Be prepared if a ﬁre starts.

▲Keep a ﬁrst aid kit and ﬁre extinguisher handy.

▲Keep emergency numbers for doctor, ambu-

lance, hospital and ﬁre department near

phone.

Wear Protective Equipment

▲Wear protective clothing and equipment.

▲Wear clothing and equipment appropriate for

the job. Avoid loose-ﬁtting clothing.

▲Because prolonged exposure to loud noise

can cause hearing impairment or hearing loss,

wear suitable hearing protection such as ear-

muffs or earplugs.

▲Because operating equipment safely requires

your full attention, avoid wearing radio head-

phones while operating machinery.

911

OFF

3/24/06 150-131Q

Important Safety Information

Handle Chemicals Properly

Agricultural chemicals can be dangerous. Im-

properuse can seriously injurepersons, animals,

plants, soil and property.

▲Read and follow chemical manufacturer’s

instructions.

▲Wear protective clothing.

▲Handle all chemicals with care.

▲Avoid inhaling smoke from any type of chemi-

cal ﬁre.

▲Store or dispose of unused chemicals as

speciﬁed by chemical manufacturer.

Use A Safety Chain

▲Use a safety chain to help control drawn

machinery should it separate from tractor

drawbar.

▲Use a chain with a strength rating equal to or

greater than the gross weight of towed

machinery.

▲Attach chain to tractor drawbar support or

other speciﬁed anchor location. Allow only

enough slack in chain to permit turning.

▲Replace chain if any links or end ﬁttings are

broken, stretched or damaged.

▲Do not use safety chain for towing.

Tire Safety

Tire changing can be dangerous and should be

performed by trained personnel using correct

tools and equipment.

▲When inﬂating tires, use a clip-on chuck and

extension hose long enough to you to stand

to one side–not in front of or over tire assem-

bly. Use a safety cage if available.

▲When removing and installing wheels, use

wheel-handling equipment adequate for

weight involved.

1205NT

150-131Q 3/24/06

Safety at All Times

Thoroughly read and understand the instructions

in this manual before operation. Read all instruc-

tions noted on the safety decals.

▲Be familiar with all drill functions.

▲Operate machinery from the driver’s seat only.

▲Do not leave drill unattended with tractor

engine running.

▲Do not dismount a moving tractor. Dismount-

ing a moving tractor could cause serious injury

or death.

▲Do not stand between the tractor and drill dur-

ing hitching.

▲Keep hands, feet and clothing away from

power-driven parts.

▲Wear snug-ﬁtting clothing to avoid entangle-

ment with moving parts.

▲Make sure all persons are clear of working

area.

▲Do not turn tractor too tightly, cause drill to ride

up on wheels. This could cause personal

injury or equipment damage.

3/24/06 150-131Q

Introduction

Great Plains Manufacturing wants you to be satis-

ﬁed with any new machine delivered by the Great

Plains Trucking network. To ease the assembly

task and produce a properly working machine,

read this entire manual before assembling or set-

ting up new equipment.

Description of Unit

14001

The 1205NT Drill is a 12' grain drill of end wheel

design which couples Great Plains spring mount-

ed coulter with a straight arm design of our solid

standopenertoachieveno-tilldrillingcapabilities.

The end wheel design keeps the ground-working

components in line with the end wheels for accu-

rate coulter depth and seed placement over un-

even terrain and allows the unit to follow ﬁeld

curves without side-loading the openers.

Intended Usage

This machine is intended to be used primarily for

No-Till drilling. It can easily be adapted for con-

ventional drilling applications.

Models Covered

1205NT

Introduction

1205NT

150-131Q 3/24/06

Using This Manual

This manual was written to help you assemble

and prepare the new machine for the customer.

The manual includes instructions for assembly

and setup. Read this manual and follow the rec-

ommendations for safe, efﬁcient and proper

assembly and setup.

An operator’s manual is also provided with the

new machine. Read and understand “Important

Safety Information” and “Operating Instructions”

in the operator’s manual before assembling the

machine. As a reference, keep the operator’s

manual on hand while assembling.

The information in this manual is current at print-

ing. Some parts may change to assure top

performance.

Deﬁnitions

The following terms are used throughout this

manual.

Right and left as used in this manual are deter-

mined by facing the direction the machine will

travel while in use unless otherwise stated.

IMPORTANT: A crucial point of information

abouttheprecedingtopic.Forsafeandcorrect

operation, read and follow the directions pro-

vided before continuing.

NOTE: Useful information about the preceding

topic.

Assembly and Setup Assistance

To order additional copies of predelivery instruc-

tionsoroperator’s andparts manuals,write to the

following address. Include model numbers in all

correspondence.

Ifyoudonotunderstandanypartofthismanualor

have other assembly or setup questions, assis-

tance is available. Contact

Product Support

Great Plains Mfg. Inc., Service Department

P.O. Box 5060

Salina, KS 67402-5060

Otros manuales para 1205NT

Tabla de contenidos

Otros manuales de Maquinaria agrícola de GREAT PLAINS

GREAT PLAINS

GREAT PLAINS Ultra Chisel 6000 Series Manual de usuario

GREAT PLAINS

GREAT PLAINS 7000 Series Guía

GREAT PLAINS

GREAT PLAINS LS10 Manual de usuario

GREAT PLAINS

GREAT PLAINS 1510HDP Manual de usuario

GREAT PLAINS

GREAT PLAINS Terra Max HT1100-20 Manual de usuario

GREAT PLAINS

GREAT PLAINS Yield-Pro Air-Pro YP625PD Manual de usuario

GREAT PLAINS

GREAT PLAINS 2SF24 Manual de usuario

GREAT PLAINS

GREAT PLAINS 706NT Manual de usuario

GREAT PLAINS

GREAT PLAINS Yield-Pro 3P4025AH Manual de usuario

GREAT PLAINS

GREAT PLAINS Nutri-Pro NP30A Manual de usuario

GREAT PLAINS

GREAT PLAINS Yield-Pro 3P4025AH Guía

GREAT PLAINS

GREAT PLAINS TCN5107 Manual de usuario

GREAT PLAINS

GREAT PLAINS PL5700 Manual de usuario

GREAT PLAINS

GREAT PLAINS LC25 Guía

GREAT PLAINS

GREAT PLAINS Yield-Pro PL5800 Manual de usuario

GREAT PLAINS

GREAT PLAINS Yield-Pro Air-Pro YP2425A Manual de usuario

GREAT PLAINS

GREAT PLAINS Turbo Max 1800TM Manual de usuario

GREAT PLAINS

GREAT PLAINS YP4425A Manual de usuario

GREAT PLAINS

GREAT PLAINS 3P1006NT Manual de usuario

GREAT PLAINS

GREAT PLAINS SS0300 Manual de usuario

GREAT PLAINS

GREAT PLAINS 8323 Manual de usuario

GREAT PLAINS

GREAT PLAINS 3P500 Manual de usuario

GREAT PLAINS

GREAT PLAINS MC5109 Max-Chisel Manual de usuario

GREAT PLAINS

GREAT PLAINS Turbo-Max 6.0M Manual de usuario

Manuales populares de Maquinaria agrícola de otras marcas

GSi

GSi PNEG-2314 Manual de usuario

Checchi & Magli

Checchi & Magli TEXDRIVE Manual de usuario

Amazone

Amazone Cenius 4003-2TX Manual de usuario

MASSEY FERGUSON

MASSEY FERGUSON MF 9313S Manual de usuario

Cima

Cima BLITZ Instrucciones de funcionamiento y mantenimiento

Amazone

Amazone CombiDisc 3000 Instrucciones de instalación

HE-VA

HE-VA Disc-Roller XL Contour Manual de usuario

AGT

AGT AGT-SSFM Manual de usuario

Milestone

Milestone 72-84 Manual de usuario

KUHN

KUHN Hector 3000 Manual de usuario

Krone

Krone X-Disc 6200 Manual de usuario

Eliet

Eliet DZC450 Manual de usuario

Taarup

Taarup BIO+ B4000 Manual de usuario

Garland

Garland SHAKER 310 DPG Manual de usuario

stable comfort

stable comfort StableWall System Manual de usuario

Raven

Raven AccuBoom Manual de usuario

International

International 710 Manual de usuario

Ashland

Ashland HDW-3217-14 Manual de usuario