GRASS VALLEY OCP400/20 Manual de usuario

www.grassvalley.com

OCP400/20-30

Operational Control Panel

Maintenance Manual

3922 496 30261

2022-12-12 V11

Notices

FCC Compliance

In order to comply with FCC/CFR47: Part 15 regulations, it is necessary to use high-quality,

triple-screened Media or Monitor cable assemblies with integrated ferrite suppression at

both ends.

Patent Information

This product may be protected by one or more patents.

For further information, please visit: www.grassvalley.com/patents/

Grass Valley®, GV® and the Grass Valley logo and/or any of the Grass Valley products listed

in this document are trademarks or registered trademarks of GVBB Holdings SARL, Grass

Valley USA, LLC, or one of its affiliates or subsidiaries. All other intellectual property rights

are owned by GVBB Holdings SARL, Grass Valley USA, LLC, or one of its affiliates or

subsidiaries. All third party intellectual property rights (including logos or icons) remain the

property of their respective owners.

Specifications are subject to change without notice.

Terms and Conditions

Please read the following terms and conditions carefully. By using OCP 400

documentation, you agree to the following terms and conditions.

Grass Valley hereby grants permission and license to owners of OCP 400 to use their

product manuals for their own internal business use. Manuals for Grass Valley products

may not be reproduced or transmitted in any form or by any means, electronic or

mechanical, including photocopying and recording, for any purpose unless specifically

authorized in writing by Grass Valley.

A Grass Valley manual may have been revised to reflect changes made to the product

during its manufacturing life. Thus, different versions of a manual may exist for any given

product. Care should be taken to ensure that one obtains the proper manual version for a

specific product serial number.

Information in this document is subject to change without notice and does not represent a

commitment on the part of Grass Valley.

Warranty information is available from the Legal Terms and Conditions section of Grass

Valley’s website (www.grassvalley.com).

Title OCP 400 Maintenance Manual

Part Number 3922 496 30261

Revision 2022-12-24 V11

iii

OCP 400

Maintenance Manual

Important Safety Information

This section provides important safety guidelines for operators and service personnel.

Specific warnings and cautions appear throughout the manual where they apply. Please

read and follow this important information, especially those instructions related to the risk

of electric shock or injury to persons.

Symbols and Their Meanings

Indicates that dangerous high voltage is present within the equipment

enclosure that may be of sufficient magnitude to constitute a risk of electric

shock.

Indicates that the user, operator or service technician should refer to the product

manuals for important operating, maintenance, or service instructions.

Indicates that static sensitive components are present, which may be damaged

by electrostatic discharge. Use anti-static procedures, equipment and surfaces

during servicing.

The presence of this symbol in or on Grass Valley equipment means that it has

been tested and certified as complying with applicable Underwriters Laboratory

(UL) regulations and recommendations for USA.

The presence of this symbol in or on Grass Valley equipment means that it has

been tested and certified as complying with applicable Canadian Standard

Association (CSA) regulations and recommendations for USA/Canada.

The presence of this symbol in or on Grass Valley equipment means that it has

been tested and certified as complying with applicable Underwriters Laboratory

(UL) regulations and recommendations for USA/Canada.

The presence of this symbol in or on Grass Valley equipment means that it has

been tested and certified as complying with applicable Intertek Testing Services

regulations and recommendations for USA/Canada.

The presence of this symbol in or on Grass Valley product means that it complies

with all applicable European Union (CE) directives.

The presence of this symbol in or on Grass Valley product means that it complies

with safety of laser product applicable standards.

Notices

Warnings

A warning indicates a possible hazard to personnel, which may cause injury or

death. Observe the following general warnings when using or working on this

equipment:

• Any instructions in this manual that require opening the equipment cover or enclosure

are for use by qualified service personnel only.

• Do not operate the equipment in wet or damp conditions. If the unit is in a wet or

damp environment, a rain cover must be used to protect it for personal safety reasons.

• Disconnect power before cleaning the equipment. Do not use liquid or aerosol

cleaners; use only a damp cloth.

• Dangerous voltages may exist at several points in this equipment. To avoid injury, do

not touch exposed connections and components while power is on.

• Prior to servicing, remove jewelry such as rings, watches, and other metallic objects.

• To avoid explosion, do not operate this equipment in an explosive atmosphere.

• Have qualified service personnel perform safety checks after any service.

Cautions

A caution indicates a possible hazard to equipment that could result in equipment

damage. Observe the following cautions when operating or working on this

equipment:

• Products that have no on/off switch, and use an external power supply must be

installed in proximity to a main power outlet that is easily accessible.

• Do not operate with suspected equipment failure. If you suspect product damage or

equipment failure, have the equipment inspected by qualified service personnel.

• To reduce the risk of electric shock, do not perform any servicing other than that

contained in the operating instructions unless you are qualified to do so. Refer all

servicing to qualified service personnel.

• Follow static precautions at all times when handling this equipment. Servicing should

be done in a static-free environment.

• Provide proper ventilation. To prevent product overheating, provide equipment

ventilation in accordance with the installation instructions. Do not block the hot airflow

coming from air outlet(s).

Precautions

To ensure continual high performance from the OCP 400 take the following

precautions into consideration:

• Avoid damp places. If the environment is wet or damp a rain cover must be used to

protect the camera.

• Do not subject the OCP 400 to severe shocks or vibration.

• Do not expose the OCP 400to extremes of temperature.

• Do not leave the OCP 400 in direct sunlight or close to heating appliances for

extended periods.

• Do not connect Grass Valley OCP 400 with other manufacturer’s camera system parts.

• Make connections swiftly and firmly to avoid false error messages.

Electrostatic Discharge (ESD) Protection

Electrostatic discharge occurs when electronic components are improperly

handled and can result in intermittent failure or complete damage adversely

affecting an electrical circuit. When you remove and replace any card from a frame

always follow ESD-prevention procedures:

• Ensure that the frame is electrically connected to earth ground through the power cord

or any other means if available.

OCP 400

Maintenance Manual

• Wear an ESD wrist strap ensuring that it makes good skin contact. Connect the

grounding clip to an unpainted surface of the chassis frame to safely ground unwanted

ESD voltages. If no wrist strap is available, ground yourself by touching the unpainted

metal part of the chassis.

• For safety, periodically check the resistance value of the antistatic strap, which should

be between 1 and 10 megohms.

• When temporarily storing a card make sure it is placed in an ESD bag.

• Cards in an earth grounded metal frame or casing do not require any special ESD

protection.

Notices

Environmental Information

European (CE) WEEE directive.

This symbol on the product(s) means that at the end of life disposal it should not be mixed

with general waste.

Visit www.grassvalley.com for recycling information.

Grass Valley believes this environmental information to be correct but cannot guarantee its

completeness or accuracy since it is based on data received from sources outside our

company. All specifications are subject to change without notice.

If you have questions about Grass Valley environmental and social involvement (WEEE,

RoHS, REACH, etc.), please contact us at environment@grassvalley.com.

vii

Laser Safety - Fiber Output SFP and QSFP Modules Warning

LASER SAFETY

The average optical output power does not exceed 0 dBm (1mW) under normal operating

conditions. Unused optical outputs should be covered to prevent direct exposure to the

laser beam.

Even though the power of these lasers is low, the beam should be treated with caution

and common sense because it is intense and concentrated. Laser radiation can cause

irreversible and permanent damage of eyesight. Please read the following guidelines

carefully:

• Make sure that a fiber is connected to the board's fiber outputs before power is

applied. If a fiber cable (e.g. patchcord) is already connected to an output, make sure

that the cable's other end is connected, too, before powering up the board.

•Do not look in the end of a fiber to see if light is coming out. The laser wavelengths

being used are totally invisible to the human eye and can cause permanent damage.

Always use optical instrumentation, such as an optical power meter, to verify light

output.

OCP 400

Maintenance Manual

viii

Notices

Safety and EMC Standards

This equipment complies with the following standards:

Safety Standards

IEC62368-1:2018

Audio/video, information and communication technology equipment: part 1

EN 62368-1:2018

EU national deviations.

EMC Standards

This unit conforms to the relevant Union harmonization legislation and the requirements of

the following directive/standards:

RED 2014/53/EU

FCC / CFR 47:Part 15 (Class A)

Federal Communications Commission Rules Part 15, Subpart B

Caution to the user that changes or modifications not expressly approved by the party

responsible for compliance could void the user's authority to operate the equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) this device may not cause harmful interference, and (2) this device must

accept any interference received, including interference that may cause undesired

operation.

following the provisions of:

• the RED directive 2014/53/EU

+Note

+ ☞ Note

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a

commercial environment.

EMC testing; EN 301 489-1 V2.2.3, EN 301 489-3 V2.1.1 and EN 301 489-19 V2.1.1.

EN 62311:2020N

Radio testing; EN 303 413 v1.1.1 (GPS)

Radio testing; EN 300 330 v2.1.1 (NFC)

This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instruction manual, may cause harmful

interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in

which case the user will be required to correct the interference at his own expense.

WARNING

Changes or modifications not expressly approved by the party responsible for compliance

could void the user's authority to operate the equipment.

OCP 400

Maintenance Manual

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Panel de control de GRASS VALLEY

GRASS VALLEY

GRASS VALLEY NV9649 Manual de usuario

GRASS VALLEY

GRASS VALLEY ATP-2000 Manual de usuario

GRASS VALLEY

GRASS VALLEY 6026 Series Manual de usuario

GRASS VALLEY

GRASS VALLEY Kaleido-RCP2 Manual de usuario

GRASS VALLEY

GRASS VALLEY L-S series Manual de usuario

GRASS VALLEY

GRASS VALLEY OCP 400 Manual de usuario

GRASS VALLEY

GRASS VALLEY NV9605 Manual de usuario

GRASS VALLEY

GRASS VALLEY JUPITER CONTROL PANEL LD16 - Manual de usuario

GRASS VALLEY

GRASS VALLEY IGNITE Manual de usuario

GRASS VALLEY

GRASS VALLEY JUPITER CONTROL PANEL SXY Manual de usuario

GRASS VALLEY

GRASS VALLEY JUPITER CONTROL PANEL S100 - Manual de usuario

GRASS VALLEY

GRASS VALLEY JUPITER LCD16 - Manual de usuario

GRASS VALLEY

GRASS VALLEY NV9640 Manual de usuario

GRASS VALLEY

GRASS VALLEY JUPITER CONTROL PANEL S25 - Manual de usuario

GRASS VALLEY

GRASS VALLEY NV9641A Manual de usuario

GRASS VALLEY

GRASS VALLEY JUPITER CONTROL PANEL LD4 - Manual de usuario

GRASS VALLEY

GRASS VALLEY JUPITER CONTROL PANEL L32 - Manual de usuario

GRASS VALLEY

GRASS VALLEY NV9680 Manual de usuario

GRASS VALLEY

GRASS VALLEY NV9000 Manual de usuario

GRASS VALLEY

GRASS VALLEY JUPITER L - S V2.1.0 Manual de usuario

GRASS VALLEY

GRASS VALLEY 6028 Series Manual de usuario

Manuales populares de Panel de control de otras marcas

RDZ

RDZ PC-HRX Manual de usuario

STG-BEIKIRCH

STG-BEIKIRCH MZ3 Manual técnico

Efka

Efka Variocontrol V810 Manual de usuario

Cebora

Cebora 208-10 Manual de usuario

AMX

AMX AutoPatch CP-15 Manual de usuario

Satel

Satel CA-6 KLED-S Manual de usuario

Evolution

Evolution IQ plus 800 Manual de usuario

Fagor

Fagor 8040 TCO CNC Manual de usuario

Trane

Trane ComfortLink II XL950 Control Manual de usuario

AKO

AKO PROCool AKO-17635-2 Manual de usuario

ABB

ABB 6136/30M-101 Manual de usuario

Telikou

Telikou BK-603 Belt Pack Manual de usuario

Mapei

Mapei Mapeheat Thermo Touch Manual de usuario

Bosch

Bosch D9412GV4 Manual de usuario

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 Manual de usuario

Sminn

Sminn BOX L VF1L EI Manual de usuario

Balboa

Balboa TP600 Manual de usuario

Nice

Nice HSCU1 Especificaciones técnicas