Granite Digital USB 2.0 to SATA/IDE Manual de usuario
Owner’
Owner’s Manual
s Manual
USB 2.0 to SA
USB 2.0 to SAT
TA / IDE
A / IDE
Bridge
Bridge Adapter
Adapter
W
Win, Mac, Linux
in, Mac, Linux
Universal USB to SATA / IDE Drive Bridge Adapter and Kit
Granite Digital • 3101 Whipple Rd. • Union City, Ca. 94587 www.granitedigital.com
Table of Contents Page
User Guide
Included in the Complete Kit 3
Bridge & Power Supply Features 4
Bridge Adapter, Power Supply, Aux. Cable
Connecting to the USB Bus 5
Connecting SATA 3.5” Hard Drives 6
Connecting IDE 3.5” Drives 7
Connecting IDE 5.25” CD / DVD Drives 8
Connecting IDE 2.5” Hard Drives 9
Using the Dual Output Power Supply 10
Formatting & Partitioning Drives 11
Diagnosing Problems 12-13
Warranty & Service 14
Granite Digital • 3101 Whipple Rd. • Union City, Ca. 94587 www.granitedigital.com
Page 3
Included in the complete kit
Included in the Kit
The Granite USB to SATA / IDE Bridge Adapter Complete Kit includes the
items listed below. The Bridge Adapter and Power Supply can also be
purchased seperately.
USB to SATA / IDE Bridge Adapter
The Bridge Adapter is powered from the
USB bus. It can connect to three different
types of drive mechanisms. SATA drives connect
to the small SATA patch cable. This cable can be
replaced with a longer cable should it be
required. IDE drives connect through the 2.5”
connector or the 3.5”, 5.25” connector.
Dual Output Drive Power Supply
The Dual Output Power Supply provides
standard 4 Pin power output and new
SATA power output switched connectors.
Plug the drive mechanism in and then turn the
switched power connector on.
AC Power Cable
Uses standard IDC Connector (like computers) to
connect to AC outlet. Generic international
cables can be substituted for 220v operation.
Auxiliary Power For Floppy Drives
The Auxiliary Power Cable provides power to
small 4 pin powered devices like Floppy Drives.
This cable also provides additional 4 pin pass
through power for bridge boards or other devices.
USB 2.0 or 1.1 Port
SATA I or II Port
SATA Power
Connector
AC Power
Cable
IDE Power
Connector
Aux. Power Cable for
Floppy & Other Devices
3.5” or 5.25”
IDE Port
2.5” IDE Port
Granite Digital • 3101 Whipple Rd. • Union City, Ca. 94587 www.granitedigital.com
Bridge & Power Supply Features
Page 4
Bridge Features
The USB Universal Bridge Adapter provides three different drive connectors.
The 7 pin connector allows any SATA mechanism to be used. The 2.5” IDE
connector works with all small laptop
mechanisms. The 3.5” or 5.25” large
IDE connector provides connectivity to
all IDE / ATA Atapi type mechanisms.
These mechanisms should be set to
(master without a slave) in order to
function properly. The USB 2.0
connector is backwards compatible
with slower version 1.1.
SATA & IDE Power
Switched Outputs
The Switched Dual Output Power Supply provides two switched power
connectors. The first is SATA Power for any SATA drive mechanism. The
second is 4 Pin IDE Power which is used on all 3.5” and 5.25” drive
mechanisms. Simply plug the connector into the drive mechanism and turn
the power on. The green LED indicates that the power is being supplied to
the drive. The IEC Power Cable provides easy connection to any AC outlet.
SATA
USB 1.1 or 2.0
2.5” IDE
3.5” & 5.25” IDE
Dual Power Switch
Power Supply Features
Granite Digital • 3101 Whipple Rd. • Union City, Ca. 94587 www.granitedigital.com
Page 5
Connecting to the USB Bus
The Universal USB
to SATA IDE Bridge Adapter
connects to most USB 1.1 or
USB 2.0 Ports. Since USB is
hot-pluggable you can connect
to any port at any time,
computer power on or
power off makes no
difference in the
operation.
Many Operating Systems immediately
indicate that the USB Bridge Adapter and
drive have been recognized and if the drive
is already formatted and partitioned in a
compabile file structure the drive will
automatically mount itself. That being said,
this is not true for all Operating Systems and
a good knowledge of how your OS works is
needed. In some systems a drive utility is
needed to format or partition the mechanism
and or mount the drive. New mechanisms
all need to go through the format and
partition routine in order to be used. Also
note that drives from different computers, i.e.
(Macintosh to/from Windows) will not be
recognized unless a third party
utility is used. Without such a
utility the OS may think that
the drive has no data on it
and ask to be re-formatted. This
of course would destroy all the data on it.
See page 12 & 13 for additional information.
Granite Digital • 3101 Whipple Rd. • Union City, Ca. 94587 www.granitedigital.com
Connecting SATA 3.5” Hard Drives
Page 6
3.5” SATA
Mechanism
3.5” SATA Mechanisms
The 3.5” SATA drive has two
connectors on the rear. The first and
larger connector is SATA Power while
the second smaller connector is for
SATA Data.
First connect the Power Supply to
the drive mechanism
using the large
SATA Power
Connector. The
connector has an “L” shape to it that needs
to be installed in the correct direction.
Make sure the power switches are in the off position and that the LED’s in
the switch box are not illuminated.
Next install the smaller SATA Data cable to the “L” shaped smaller
connector. The USB to SATA IDE Bridge Adapter comes with a very short
SATA Cable that can be replaced with a longer one should additional cable
length be necessary. Granite has a variety of longer length cables available.
The type of connection is SATA “L” type. This is the generic connector and
not the shielded external eSATA “I” type
used on many external SATA storage
systems. Lastly, connect the USB Cable to
the computer and turn the switch on.
SATA Power SATA Data
Granite Digital • 3101 Whipple Rd. • Union City, Ca. 94587 www.granitedigital.com
Page 7
Connecting IDE 3.5” Hard Drives
3.5” IDE
Mechanism
3.5” IDE
Mechanisms
The 3.5” IDE drive has two connectors on the rear. The larger, 40 pin
connector is IDE DATA while the smaller, 4 pin connector is for
Drive Power. Plug in the DrivePower connector. This connector has cut
corners and must be installed with the correct orientation. Make sure the
power switches are in the off position and
that the LED’s in the switch box are not
illuminated.
Next plug in the larger IDE Data
connector located on the Bridge Adapter.
This 40 pin connector is keyed and can
only be inserted in one direction. Plug
the USB Connector into the computer
and turn the power switch on.
IDE Drive jumpers
should be set to
Cable Select
or Master.
It the drive
doesn’t show up
try the both setting.
Granite Digital • 3101 Whipple Rd. • Union City, Ca. 94587 www.granitedigital.com
Connecting IDE 5.25” CD / DVD
Page 8
5.25” CD / DVD
Mechanism
The 5.25” IDE CD/DVD drive has two connectors on the rear. The larger, 40
pin connector is IDE DATA while the smaller, 4 pin connector is for
Drive Power. Plug in the DrivePower connector. This connector has cut
corners and must be installed with the correct orientation. Make sure the
power switches are in the off position and
that the LED’s in the switch box are not
illuminated.
Next plug in the larger IDE Data
connector located on the Bridge Adapter.
This 40 pin connector is keyed and can
only be inserted in one direction. Plug
the USB Connector into the computer
and turn the power switch on.
5.25” IDE
CD / DVD
Mechanisms
Granite Digital • 3101 Whipple Rd. • Union City, Ca. 94587 www.granitedigital.com
Page 9
Connecting IDE 2.5” Hard Drives
Laptop
NoteBook
2.5” Mechanism
The 2.5” IDE Drive has one connector on
the rear. This 44 pin connector is IDE
DATA and IDE Power combined. This
connector has a blocked socket and must
be installed in the correct orientation.
Match the blocked socket with the missing
pin on the drive mechanism.
2.5” IDE Drive Mechanisms get their
power from the USB port. In this case, the
Universal Power Supply is not needed.
2.5” IDE
Mechanisms
Granite Digital • 3101 Whipple Rd. • Union City, Ca. 94587 www.granitedigital.com
Using the Dual Output Pwr Supply
Page 10
The Dual Output Power Supply is capable of supplying power to all types of
drives. When used with the included Auxiliary Power Cable, IDE, SATA, and
Floppy Drives can all be connected to the power supply.
The SATA Drive Power connector plugs into any SATA Drive Mechanism.
The “L” type connector must be oriented correctly before it is plugged in.
Power should only be supplied to the SATA Drive Mechanism after all the
cables have been connected including the SATA Data Cable from the Bridge
Adapter.
The IDE Drive Power connector plugs into any standard IDE, ATAPI, ATA, or
SCSI type of drive mechanism. Power should only be supplied to the Drive
Mechanism after the Data Cable has been connected to the Bridge Adapter.
Standard IDE Drive
Power 4-Pin Connector
SATA Drive Power
15 Contact Connector
Dual Output Switch
with LED Power ON
Indicators
Tabla de contenidos
