Graco T-MAX 506 Manual

T-MAX™506/657

www.graco.com

STARTUP

STARTUP Spray with Air <= 1.5 mm

Fill material hopper

with pre-mixed texture

material.

Turn pressure control

knop until a steady

stream flows from

material hose. Turn pump OFF.

Turn applicator OFF,

Turn ON/OFF switch

to ON

Lossen nut on bottom

of pump

two to three turns to

relieve pressure

Turn pressure control

to maximum. To spray,

aim applicator with a

distance of 0,5 m to the

wall and open applictor.

To clean a tip clog, turn

applicator OFF, turn Tip 180°

to Clean position, aim in waste

area, turn applicator ON, when

clog clears, turn applictor OFF

and tip in spray postion.

Turn pressure

control off (0).

Point applicator

into hopper.

Turn applicator ON.

DO NOT USE WITH

QUICK-SET MATERIALS

Pressure Relief

DO NOT USE WITH

QUICK-SET MATERIALS

Pressure

Relief

Use different tip size

for different flow

Install filter and tip

extension.

Connect applicator

to material hose.

Add water if thinning is

required. Mix thoroughly.

HDA531

HDA535

HDA541

HDA545

HDA651

HDA661

HDA671

mc03 m

Spray without Air < .25 mm

Srew tip assembley

onto applicator

Fill material hopper with

mixed texture material.

Place material hose in Hopper turn ON/OFF switch to ON Turn

control in the “green” segment, allow material to circulate 30 sec.

Turn pump control to

shut pump off

Screw air hose and valve to applicator.

Connect material hose to gun kit

Turn applicator valve OFF.

Install air nozzle.

Hold applicator over

material hopper and turn

applicator ON.

Turn air compressor ON. Turn pump

control in the “green” area, until

desired material rate is achieved.

Regulate the air valve to

get a good atomization.

To stop spraying,

turn applicator OFF

Quick Operator’s Guide

SETUP

This procedure is for water-base paints and flushing fluids. For solvent-base paints and flushing

fluids (i.e. mineral spirits), you must read Fire and Explosion Hazard in the Operating Instructions.

* check the Graco operations manual delivered with the unit for more details.

WARNING

Turn pump control off (0).

Connect power cord.Connect pump module to hopper cart.

Remove pump plug.

Connect material hose to pump outlet.

PRESSURE RELIEF PROCESS

Turn pump control counter clockwise,

to shut pump off.

Close applictor after pressure release,

close air valve

Scrape material remaining in

hopper into pump to be pumped

from sprayer.

Rotate pump control to

(0) to shut pump off.

Shut OFF air compressor if spraying with air.

Remove applicator from material hose.

Clean applicator.

Rotate pump control

clockwise to start pump.

Rotate pump control to (0) to

shut pump off.

Clean applicator, spray tips and

guard with brush.ON/OFF switch to OFF

Turn pump control

clockwise and pump

unused texture material

from material hopper

and hose.

Run pump until

cleaning ball exits

material hose.Save

cleaning ball. Repeat

it till the water that

comes out is clear.

Insert wet cleaning ball into pump.

Connect material hose to pump outlet.

Clean hardened material

from applicator nozzles

with air nozzle cleaner.

Remove drain plug from Hopper

Clean hopper with water, brush

and sponge, install drain plug. fill

hopper 1/3 with clear water.

GRACO DISTRIBUTION BVBA Industrieterrein Oude Bunders

Slakweidestraat 31 • B-3630 Maasmechelen

Tel: +32 (89) 770 700 • Fax: +32 (89) 770 777

www.graco.com

Graco is certified ISO 9001.

All information, illustrations, and specifications in this document are based on the latest product information

available at the time of publication. The right is reserved to make changes at any time without notice.

CHOOSE THE RIGHT TIP (HDA-XXX)

CLEANUP

XTRA LIGHT LIGHT MEDIUM HEAVY

HDA531 HDA541 HDA651 HDA671

HDA535 HDA545 HDA661 -

VERY FINE - 3MM FINE - 4MM MEDIUM - 6MM MEDIUM HEAVY - 8MM HEAVY - 10MM

248888 248524 248525 248526 248527

Otros manuales para T-MAX 506

Este manual sirve para los siguientes modelos

Otros manuales de Pistola pulverizadora de pintura de Graco

Graco

Graco 232833 Manual de usuario

Graco

Graco 207-945 Manual de operación

Graco

Graco 231-323 Manual de operación

Graco

Graco 190ES 261825 Manual de usuario

Graco

Graco Monark 03289A Manual de usuario

Graco

Graco EM 5000 Manual de operación

Graco

Graco 311286C Manual de instrucciones

Graco

Graco PRO AA5500SC Manual de usuario

Graco

Graco 278675 Manual de instrucciones

Graco

Graco 313483A Manual de uso y cuidado

Graco

Graco GH 200 Manual de instrucciones

Graco

Graco XPs-hf Series Manual de uso y cuidado

Graco

Graco Ultra Max 309273 Manual de usuario

Graco

Graco EM 480 Hydra-Spray Manual

Graco

Graco T Series Manual de operación

Graco

Graco 224200 Manual de operación

Graco

Graco ULTRA R MAX 695 309067 Manual de operación

Graco

Graco EH 333 HYDRA-SPRAY A Series Manual de operación

Graco

Graco RS Instrucciones de funcionamiento

Graco

Graco Finex 24C308 Manual de usuario

Graco

Graco C59519 Manual de operación

Graco

Graco 255963 Manual de lista de piezas

Graco

Graco Pro 230ES Manual de usuario

Graco

Graco ProShot 258865 Manual de usuario

Manuales populares de Pistola pulverizadora de pintura de otras marcas

SNOWJOE

SNOWJOE Sunjoe 24V-GS-LTW-RM Manual de usuario

Binks

Binks SV100 Manual de usuario

Fimco

Fimco LG-4-3-1 Manual de usuario

AG SPRAY

AG SPRAY FS-ATV-25BL Manual de usuario

Nordson

Nordson MicroMax 2 Manual de usuario

Bonide

Bonide 051 Manual de operación

zogics

zogics Z-DAS Manual de usuario

KISANKRAFT

KISANKRAFT KK-KBS-165 Manual de usuario

Matrix

Matrix SG 650 Manual de usuario

Anest Iwata

Anest Iwata SGA-3 Guía de inicio rápido

paasche

paasche VV Hoja de datos

Carlisle

Carlisle DeVilbiss JGA-510 Manual de usuario

Gardena

Gardena 11120 Manual de usuario

Conrad

Conrad Hobby Airbrush K3 Manual de usuario

wiwa

wiwa 14025 R/F Manual de usuario

DeVilbiss

DeVilbiss LUNA2i Manual de usuario

WAGNER

WAGNER W 125 Manual de usuario

My Clean Buddy

My Clean Buddy PW018 Manual de usuario