Graco RentalPro 230PC HDR Manual de usuario

Read Operation manual 334641 for complete instructions and warnings.

Manuals are available from your rental associate, calling Graco at 1-800-690-2894, or at

www.graco.com.

This guide is not a substitute for reading and understanding all operation manuals and warning labels supplied with

the equipment. It is important that you read and understand all warnings and instructions before operating this

equipment.

SKIN INJECTION HAZARD: High-pressure spray is able to inject toxins into the body and cause serious bodily

injury. In the event that injection occurs, get immediate surgical treatment. Keep clear of spray tip and leaks.

Engage trigger lock when not spraying.

Follow the pressure relief procedure

and wear protective equipment including but not limited to protective eye wear.

FIRE/EXPLOSION HAZARD: Sprayer generates sparks. Use only in well ventilated areas.

FAILURE TO FOLLOW ALL WARNINGS CAN RESULT IN SERIOUS INJURY, AMPUTATION OR DEATH.

PREPARE SPRAYER FOR RENTAL

Pre-Rental Check List

Operational check, start unit and check for

proper operation, follow SETUP and PRIME

instructions, page 2.

Use water to test sprayer and spray a test

pattern. Perform Pressure Relief Procedure.

Verify proper operation of gun trigger lock. Offer renter a copy of Operation Manual 334641.

Demonstrate to renter:

• Use of trigger lock

• How to clear a tip clog

• Pressure relief procedure

Provide renter a copy of the Customer

Operation Guide.

PRESSURE RELIEF PROCEDURE - WATER-BASED MATERIALS

Follow the pressure relief procedure whenever you see this symbol.

ti25643a

5 6

321 7

Tool Turn Guide

Pro Painter Sprayer (RentalPro®230PC HDR)

Tool Rental Center Technical Assistance 1.800.543.0339

www.graco.com

WARNING

RENTAL PREPARATION – WHEN USING WATER-BASED MATERIALS.

When using oil-based materials read and follow the Operation manual.

Recommended for rental only with water based materials due to sprayer maintenance

and clean up difficulties which can result in machine damage and associated costs.

335016B

Electric Airless Sprayer

PREPARE SPRAYER FOR RENTAL (continued)

SETUP - WATER-BASED MATERIALS

Steps 1 & 2: Connect hose connections and tighten. Steps 3 – 6: Engage trigger lock, install tip guard, turn switch OFF,

and plug unit in. Steps 7 – 12: Flush with clean water until clear water comes out of the drain tube.

Step 13: Perform Pressure Relief Procedure.

PRIME - WATER-BASED MATERIALS

Step 2: Place fluid intake in water. Step 6:Trigger gun until water appears. Release gun trigger and allow pressure to build. Engage

trigger lock. Inspect for leaks. If leaks occur, perform Pressure Relief Procedure then tighten all fittings and repeat this procedure.

Step 7: Perform Pressure Relief Procedure.

1234 5 6

ti25645a

8 9 10 11 12

ti25645b

ti26172a

15 s

620 s

Technical Assistance:1 (800) 543-0339

Customer Service: 1 (800) 690-2894

2335016B

PREPARE SPRAYER FOR STORAGE

Storage Check List

Perform Cleanup procedure, follow CLEANUP

instructions, page 3. Inspect sprayer for safety labels, replace as

necessary.

To prevent corrosion flush with Pump Armor™.

Pump Armor

243103 1 quart/0.95 liter

Pump Armor

245133 1 gallon/3.8 liter

Inspect motor shield vents for blockage.

Fill throat packing nut with TSL™.

TSL 206995 1 quart/0.95 liter

TSL 206995 1 gallon/3.8 liter

If used, remove disposable hose cover and

inspect hose for kinks and bulges. Replace

damaged hose.

Throat packing adjustment

When pump packings begin to leak after much use,

tighten packing nut down until leakage stops or lessens.

This allows approximately 100 gallons of additional

operation before a repacking is required. Packing nut can

be tightened without o-ring removal.

Inspect power cord and plug, make certain that

they are not damaged. Make certain ground pin

is on the plug and not damaged. If cord or plug

is damaged replace cord.

Wipe sprayer off with a clean dry rag. Do not

use a pressure washer to clean the sprayer. Check trigger lock operation.

Verify trigger stop adjustment, page 4.

Replace trigger guard if damaged or missing.

Clean and inspect filters. Complete inspection tag and attach to sprayer.

CLEANUP - WATER-BASED MATERIALS

Steps 4 – 6: Flush with clean water until clear water comes out of the drain tube. Step 8: Trigger gun until water comes out clear.

Step 9: Place fluid intake in to a pail of Pump Armor. Turn prime valve down. Turn pressure control to Fast Flush. Operate untilpump

runs steady and Pump Armor appears in the waste pail. Step 11: Fill throat packing nut with TSL.

Step 12: Perform Pressure Relief Procedure. Step 13: Clean and inspect filters. Step14: Wipe sprayer off with clean dry rag.

2 3 4 5 6

11 12 13

ti26181a

Technical Assistance:1 (800) 543-0339

Customer Service: 1 (800) 690-2894

335016B

GUN TRIGGER STOP ADLUSTMENT

Test Trigger Stop Adjustment

1. Trigger gun into a bucket until fluid flows from the gun.

2. Release trigger, fluid flow should stop immediately.

3. Engage trigger lock (A).

4. Aim gun into a bucket.

Trigger gun, no fluid should flow from the gun tip.

5. If the gun fails test, perform Pressure

Relief Procedure, disconnect hose, and adjust trigger stop.

Adjust Trigger Stop

1. Engage trigger lock (A).

2. Hold gun with nozzle tip facing up (B).

3. Tighten adjustment nut until trigger begins to rise. (C)

4. Loosen adjustment nut 3/4 turn (D).

5. Repeat trigger stop adjustment test.

ti26175a

3/4

Original Instructions. This manual contains English. MM 335016. Revision B, September 2015

Technical Assistance:1 (800) 543-0339

Customer Service: 1 (800) 690-2894

Otros manuales para RentalPro 230PC HDR

Tabla de contenidos

Otros manuales de Pistola pulverizadora de pintura de Graco

Graco

Graco 238256 Manual de operación

Graco

Graco LineLazer II 3900 Manual de usuario

Graco

Graco Series E Manual de operación

Graco

Graco PRO AA5500SC Hoja de datos

Graco

Graco 24V112 Manual de instrucciones

Graco

Graco 231-581 A Series Manual de operación

Graco

Graco HydraMax-225 233640 Manual de usuario

Graco

Graco ti2652a Manual de usuario

Graco

Graco TrueCoat 360 Manual de usuario

Graco

Graco 231-033 Manual de operación

Graco

Graco 17R236 Guía

Graco

Graco Pro 270GS Manual de instrucciones

Graco

Graco Project Series Manual de usuario

Graco

Graco PRO 3Z9296 Manual de usuario

Graco

Graco ti2652b Manual de usuario

Graco

Graco TrueCoat 360 DS Manual de usuario

Graco

Graco Contractor ST Manual de operación

Graco

Graco 240-349 Manual de operación

Graco

Graco XM 24W626 Manual de usuario

Graco

Graco Edge 256855 Manual de usuario

Graco

Graco 207-279 Manual de usuario

Graco

Graco HYDRA-CLEAN C Series Manual de operación

Graco

Graco Reactor 2 E-30 Manual de uso y cuidado

Graco

Graco LineLazer ll 5900 Manual de instrucciones

Manuales populares de Pistola pulverizadora de pintura de otras marcas

SNOWJOE

SNOWJOE Sunjoe 24V-GS-LTW-RM Manual de usuario

Binks

Binks SV100 Manual de usuario

Fimco

Fimco LG-4-3-1 Manual de usuario

AG SPRAY

AG SPRAY FS-ATV-25BL Manual de usuario

Nordson

Nordson MicroMax 2 Manual de usuario

Bonide

Bonide 051 Manual de operación

zogics

zogics Z-DAS Manual de usuario

KISANKRAFT

KISANKRAFT KK-KBS-165 Manual de usuario

Matrix

Matrix SG 650 Manual de usuario

Anest Iwata

Anest Iwata SGA-3 Guía de inicio rápido

paasche

paasche VV Hoja de datos

Carlisle

Carlisle DeVilbiss JGA-510 Manual de usuario

Gardena

Gardena 11120 Manual de usuario

Conrad

Conrad Hobby Airbrush K3 Manual de usuario

wiwa

wiwa 14025 R/F Manual de usuario

DeVilbiss

DeVilbiss LUNA2i Manual de usuario

WAGNER

WAGNER W 125 Manual de usuario

My Clean Buddy

My Clean Buddy PW018 Manual de usuario