Graco Idler 257817 Manual de usuario

313900A

Repair Kit

Idler Repair Kit 257817

- For servicing FinishPro 290 Sprayers -

Pressure Relief Procedure

Important Safety Instructions

For detailed instructions and warnings,

see sprayer manual.

To reduce the risk of injury from injection, always follow

this procedure when instructed to relieve pressure,

stop spraying, service equipment, or install or clean

spray tip.

1. Set power/function selection switch to OFF and

unplug sprayer.

2. Turn pressure knob to lowest setting.

3. Hold gun to side of grounded metal pail. Trigger the

gun to relieve pressure.

4. Turn prime valve to PRIME.

If you suspect spray tip or hose is completely clogged, or

that pressure has not been fully relieved after following

these steps, VERY SLOWLY loosen tip guard retaining

nut or hose end coupling to relieve pressure gradually,

then loosen completely. Clear tip or hose obstruction.

ti9346a

ti14351a

2313900A

Disassembly

1. Relieve Pressure (see cover) and unplug sprayer.

2. Loosen IEC cord clamp screw and remove IEC plug

from compressor.

3. Remove air hose from compressor and remove out-

let fitting from compressor.

4. Remove four screws. Tip compressor assembly

down and forward to remove from sprayer. Place

compressor on workbench.

5. Remove two screws and IEC cord clamp. Remove

two screws and compressor shroud.

6. Remove three screws and belt cover.

7. Remove top and bottom idler pulley bracket screws

and remove idler assembly.

8. Remove three screws and motor belt guide plate.

9. Remove belt from pulleys.

ti13409a

ti13411a

ti13416a

Belt Cover

ti13414a ti13664a

ti13413a

ti14352a

ti13407a

313900A 3

Reassembly

1. Install new belt and guide plate with three screws.

2. Install idler assembly with two screws and washer

as shown. Do not fully tighten screws.

3. Place torque wrench in square hole and torque to

60 in-lb to properly tension belt. Tighten top and bot-

tom idler screws.

4. Torque top and bottom idler screws to 120 in-lb.

5. Install belt cover with three screws.

6. Install compressor shroud with two screws. Install

IEC cord clamp with two screws.

7. Install compressor outlet fitting.

8. Tip compressor assembly up and back into frame.

Install four screws.

9. Install IEC connector and tighten cord clamp. Install

air hose to outlet fitting. Make sure cord is pushed in

as far as it can go to ensure a good connection and

the screw is tightened securely.

ti13443a

ti14352a

ti13417a

ti13418a ti13419a

ti13413a

ti13414a ti13664a

ti13411a

ti13442a

ti13420a

4313900A

All written and visual data contained in this document reflects the latest product information available at the time of publication.

Graco reserves the right to make changes at any time without notice.

This manual contains English. MM 313900

Graco Headquarters: Minneapolis

International Offices: Belgium, China, Japan, Korea

GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440-1441

www.graco.com

Otros manuales de Pistola pulverizadora de pintura de Graco

Graco

Graco ti2652a Manual de usuario

Graco

Graco 231979 Manual de operación

Graco

Graco 311365G Instrucciones de funcionamiento

Graco

Graco XTR7+ XTR720 Manual de usuario

Graco

Graco 309410 Guía de inicio rápido

Graco

Graco XHF Manual de lista de piezas

Graco

Graco HYDRA-SPRAY KING Manual de operación

Graco

Graco 16R955 Guía

Graco

Graco SaniSpray HP 750 Manual de usuario

Graco

Graco 232630 Instrucciones de funcionamiento

Graco

Graco TrueCoat 360 Manual de usuario

Graco

Graco Reactor E-10 Manual de operación

Graco

Graco GMax 232611 Instrucciones de funcionamiento

Graco

Graco 245866 Manual de usuario

Graco

Graco TexSpray RTX 750 Instrucciones de funcionamiento

Graco

Graco AirPro 237413 Series A Manual de operación

Graco

Graco PT2500 Manual de operación

Graco

Graco 240539 Manual de usuario

Graco

Graco 700N Manual de usuario

Graco

Graco ti2652b Manual de usuario

Graco

Graco AirPro 312414 Manual de lista de piezas

Graco

Graco Reactor 2 H-30 Manual de uso y cuidado

Graco

Graco 231-547 Manual de operación

Graco

Graco Reactor A-20 Manual de uso y cuidado

Manuales populares de Pistola pulverizadora de pintura de otras marcas

SNOWJOE

SNOWJOE Sunjoe 24V-GS-LTW-RM Manual de usuario

Binks

Binks SV100 Manual de usuario

Fimco

Fimco LG-4-3-1 Manual de usuario

AG SPRAY

AG SPRAY FS-ATV-25BL Manual de usuario

Nordson

Nordson MicroMax 2 Manual de usuario

Bonide

Bonide 051 Manual de operación

zogics

zogics Z-DAS Manual de usuario

KISANKRAFT

KISANKRAFT KK-KBS-165 Manual de usuario

Matrix

Matrix SG 650 Manual de usuario

Anest Iwata

Anest Iwata SGA-3 Guía de inicio rápido

paasche

paasche VV Hoja de datos

Carlisle

Carlisle DeVilbiss JGA-510 Manual de usuario

Gardena

Gardena 11120 Manual de usuario

Conrad

Conrad Hobby Airbrush K3 Manual de usuario

wiwa

wiwa 14025 R/F Manual de usuario

DeVilbiss

DeVilbiss LUNA2i Manual de usuario

WAGNER

WAGNER W 125 Manual de usuario

My Clean Buddy

My Clean Buddy PW018 Manual de usuario