Graco HVLP 2500 Manual

www.graco.be

HVLP 2500/3800/4900

Quick Operator’s Guide

SETUP

This procedure is for water-base paints and flushing fluids. For solvent-base paints and flushing

fluids (i.e. mineral spirits), you must read Fire and Explosion Hazard in the Operating Instructions.

* check the Graco operations manual delivered with the unit for more details.

WARNING

Remove cup. Fill 3/4 full. DO NOT

OVERFILL. Reattach and latch cup.

Turn fluid control out until trigger movement is not restricted.

Caution: Turning knob too far will remove it.

Connect air hose to gun and turbine.

CHOOSE THE RIGHT FLUID NOZZLE

For low flow rates or light

viscosity fluid, select smaller

nozzle sizes.

For high flow rates or high

viscosity fluid, select larger

nozzle sizes.

Installing the Fluid Set

Use your hand to loosen and remove the air cap retaining (A) and the air cap

housing (B).

While triggering the gun, use your hand to loosen and remove the nozzle (C)

from the gun.

Use your hand to loosen and remove the fluid knob assembly (D) and com-

pression spring (E) from back of gun and remove the old needle.

Insert the needle assembly (F) into the back of the gun. Replace the nozzle

(E,D) air cap housing (C,B,A) and air cap retaining ring and tighten by hand.

NOTE: O-ring (G) should always be on the nozzle.

Material

Part Number

Orifice Size

Fluid Set #2 Fluid Set #3 Fluid Set #4 Fluid Set #5 Fluid Set #6 Turbine Unit

244123 244124 244125 244126 244127

0.032 0.051 0.071 0.087 0.098

Dye

Ink 2500

Non-Wiping Stain

Automotive Finish

Lacquer

Stain

Enamel 3800

Epoxy

Urethane

Varnish

Primer

Industrial Finishers

Latex

Multi-Spec

Butyrate 4900

Nitrate Dope

Oil Wall Paint

NOTE: read gun manual for paint reduction recommendations.

All manuals and user guides at all-guides.com

SPRAYING

Plug turbine power cord into

a grounded outlet.

GRACO N.V. • Industrieterrein Oude Bunders

Slakweidestraat 31 • B-3630 Maasmechelen

Tel. (32) 89 770 700 • Fax (32) 89 770 777 All information, illustrations, and specifications in this document are based on the latest product information

available at the time of publication. The right is reserved to make changes at any time without notice.

Graco Inc. is registered to I.S. EN ISO 9001.

Open air control valve.

Turn air cap to obtain

desired direction. Lock air cap with retaining ring.

Turn turbine on.

Wait several minutes

prior to spraying to

allow warm-up time.

Nozzle

Air Cap

Air Control

Pattern Selection

Knob

Fluid Knob

Retaining Ring

SHUTDOWN

Turn off turbine. Unlatch cup.

CLEANING

Disassemble gun from cup and clean all parts with water.

Round Pattern

Set knob to RND Vertical or horizontal Pattern

Set knob to FAN

Select spray pattern by adjusting the fluid knob

and pattern selection knob. The air control

adjusts the TOTAL air to the pattern and gun.

Hold gun perpendicular, 6-8 inches

from surface. Move gun first, then

pull gun trigger to spray.

To control over-

spray, reduce

air flow or

reduce fluid

volume.

NOTE: If fluid is

not atomizing

properly, fluid

may need to be thinned further, or

a different tip size may be used.

All manuals and user guides at all-guides.com

Otros manuales para HVLP 2500

Este manual sirve para los siguientes modelos

Otros manuales de Pistola pulverizadora de pintura de Graco

Graco

Graco 231409 Manual de operación

Graco

Graco 223–390 Manual de operación

Graco

Graco 218-688 Manual de operación

Graco

Graco 310813D Instrucciones de funcionamiento

Graco

Graco 257369 Instrucciones de funcionamiento

Graco

Graco 262927 Manual de usuario

Graco

Graco REACTOR E-20 Instrucciones de montaje

Graco

Graco 232624 Manual de operación

Graco

Graco Monark Hydra-Spray D Series Manual de operación

Graco

Graco ToughTek M680a Manual de uso y cuidado

Graco

Graco ULTRA PLUS+ 750 Manual de operación

Graco

Graco ThermoLazer 258699 Instrucciones de funcionamiento

Graco

Graco Delta Spray 237409 Manual de operación

Graco

Graco 245924 Manual de usuario

Graco

Graco 241284 Manual de usuario

Graco

Graco SaniSpray HP 20 Manual de uso y cuidado

Graco

Graco ST Guía de configuración

Graco

Graco EM 490 Manual de operación

Graco

Graco 288048 Manual de lista de piezas

Graco

Graco ultra 750 Manual de usuario

Graco

Graco 3A4803A Guía

Graco

Graco 245924 Manual de usuario

Graco

Graco 288046 Manual de lista de piezas

Graco

Graco 239-766 Manual de usuario

Manuales populares de Pistola pulverizadora de pintura de otras marcas

SNOWJOE

SNOWJOE Sunjoe 24V-GS-LTW-RM Manual de usuario

Binks

Binks SV100 Manual de usuario

Fimco

Fimco LG-4-3-1 Manual de usuario

AG SPRAY

AG SPRAY FS-ATV-25BL Manual de usuario

Nordson

Nordson MicroMax 2 Manual de usuario

Bonide

Bonide 051 Manual de operación

zogics

zogics Z-DAS Manual de usuario

KISANKRAFT

KISANKRAFT KK-KBS-165 Manual de usuario

Matrix

Matrix SG 650 Manual de usuario

Anest Iwata

Anest Iwata SGA-3 Guía de inicio rápido

paasche

paasche VV Hoja de datos

Carlisle

Carlisle DeVilbiss JGA-510 Manual de usuario

Gardena

Gardena 11120 Manual de usuario

Conrad

Conrad Hobby Airbrush K3 Manual de usuario

wiwa

wiwa 14025 R/F Manual de usuario

DeVilbiss

DeVilbiss LUNA2i Manual de usuario

WAGNER

WAGNER W 125 Manual de usuario

My Clean Buddy

My Clean Buddy PW018 Manual de usuario