Graco 15H885 Manual de usuario
Graco Inc. P.O. Box 1441 Minneapolis, MN 55440-1441
Copyright 2007, Graco Inc. is registered to I.S. EN ISO 9001
Allows a computer to communicate with the Graco Variable Frequency Drive
(VFD).
Important Safety Instructions
Read all warnings and instructions in this manual
and in Variable Frequency Drive manual 311596.
Save these instructions.
Refer to SM-Ethernet User Guide by Control Techniques
for detailed installation and operation instructions.
311612 rev.A
Instructions
15H885 Ethernet
Upgrade Kit
Installation and Operation
2311612A
Installation and Operation
1. Disconnect power to the VFD.
2. Disable the Hardware Enable input (press Secure
Disable switch).
3. Install Ethernet Module (C) into slot 2 on the VFD
(or slot 1 if slot 2 is not available).
4. Apply power to the VFD.
5. If this is the first time Ethernet module is installed
into the VFD, “SL2.dF” fault becomes active. Reset
the fault by pressing the red Stop/Reset switch.
6. Set IP address:
IP address is located in Pr MM.10, MM.11, MM.12,
and MM.13 (Pr 16.10, 16.11, 16.12, and 16.13 if slot
2 is used).
For a Fixed IP address:
a. Default IP address is 192.168.1.100. If default
IP address is acceptable, navigate to Pr MM.00
(Pr 16.00 if installed in slot 2), set its value to
1000, and press the red Stop/Reset switch to
save the default address, which will allow the
Ethernet module to use it at every power-up.
b. If IP address must be changed from the default,
change the address, then navigate to Pr MM.00
(Pr 16.00 if installed in slot 2), set its value to
1000, and press the red Stop/Reset switch.
c. For the module to start using the new address,
the module needs to be reset. Navigate to Pr
MM.00 (Pr 16.00 if installed in slot 2), set its
value to 1070, and press the red Stop/Reset
switch to reset the module.
DHCP (Dynamic Host Configuration Protocol)
DHCP server can provide the SM-Ethernet module
with an IP address:
a. Navigate to Pr MM.05 (Pr 16.05 if installed in
slot 2) and set it to 1, allowing use of DHCP.
b. Navigate to Pr MM.00 (Pr 16.00 if installed in
slot 2), set its value to 1000, and press the red
Stop/Reset switch to save the change, which
will allow the Ethernet module to use DHCP.
c. For the module to start using DHCP and to
acquire the IP address, the module needs to be
reset. Navigate to Pr MM.00 (Pr 16.00 if
installed in slot 2), set its value to 1070, and
press the red Stop/Reset switch to reset the
module.
Never install or remove the Ethernet module while
power is applied to the VFD.
C
Note that Code 1070 will cause the AppsLite mod-
ule to reset as well, which will cause the pump to
stop running if it was not stopped prior to the reset.
Note that Code 1070 will cause the AppsLite mod-
ule to reset as well, which will cause the pump to
stop running if it was not stopped prior to the reset.
E-Flo Plus Software
311612A 3
E-Flo Plus Software
The CD supplied with the kit includes zipfile 15K581,
which contains the E-Flo Plus software (Visual Basic
application). Install the CD into your computer, extract
the files from the zipfile, and follow the software installa-
tion instructions as they appear on the screen.
Once the installation is complete the icon will
appear on the screen.
See the instruction in the VFD manual 311596 to com-
plete the software installation and for operating instruc-
tions.
Graco uses a Visual Basic program to display the
run screen on the computer. This software and
program is not supported by Graco.
All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
MM 311612
Graco Headquarters: Minneapolis
International Offices: Belgium, China, Japan, Korea
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440-1441
www.graco.com
1/2007
Graco Standard Warranty
Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in
material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty
published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by
Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written
recommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty
installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of
non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with
structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or
maintenance of structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of
the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned
to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will
be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED
TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy
(including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or
consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.
GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT
MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to
the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these
warranties.
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or
the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the
negligence of Graco, or otherwise.
FOR GRACO CANADA CUSTOMERS
The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into,
given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la
rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite
de ou en rapport, directement ou indirectement, avec les procédures concernées.
Graco Information
TO PLACE AN ORDER, contact your Graco distributor or call to identify the nearest distributor.
Phone: 612-623-6921 or Toll Free: 1-800-328-0211 Fax: 612-378-3505
Otros manuales de Hardware de red de Graco
Manuales populares de Hardware de red de otras marcas
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Manual de usuario
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Manual de usuario
Yudor
Yudor YDS-16 Manual de usuario
D-Link
D-Link ShareCenter DNS-320L Manual de usuario
Samsung
Samsung ES1642dc Instrucciones de uso
Honeywell Home
Honeywell Home LTEM-PV Instrucciones de montaje
