Goodman ASXC160361A Manual de usuario

*SXC 16 SEER

Condensing Units

•RefertoServiceManualRS6200006forinstallation,operation,andtroubleshootinginformation.

•Allsafetyinformation must be followedasprovided in the ServiceManual.

•RefertotheappropriatePartsCatalogfor part number information.

•See models on page 3.

TECHNICAL MANUTECHNICAL MANU

TECHNICAL MANUALAL

ALAL

RT6114004r11

August2014

This manual is to be used by qualified, professionally trained HVAC technicians only. Goodman does

not assume any responsibility for property damage or personal injury due to improper service

procedures or services performed by an unqualified person.

PRODUCT IDENTIFICATION

The model number is used for positive identification of component parts used in manufacturing. Please use this number

whenrequestingserviceorpartsinformation.

WARNING

WARNING HIGH VOLTAGE!

Disconnect ALL power before servicing or installing this unit. Multiple power

sources may be present. Failure to do so may cause property damage, personal

injury or death.

ONLY individuals meeting (at a

minimum) the requirements of

an "entry level technician" as specified by the Air-Condi-

tioning, Heating, and Refrigeration Institute (AHRI) may

use this information. Attempting to install or repair this

unit without such background may result in product

damage, personal injury or death.

Goodman will not be responsible

for any injury or property damage

arising from improper service or service procedures. If

you install or perform service on this unit, you assume

responsibility for any personal injury or property damage

which may result. Many jurisdictions require a license to

install or service heating and air conditioning equipment.

WARNING

WARNING WARNING

WARNING

DSXC160241AA

PRODUCT TYPE:

C:CondenserR-22

H:Heat Pump R-22

X: Condenser R-410A

Z: Heat Pump R-410A

PRODUCT

FAMILY:

S: Split System

SEER:

SEER Rating

BRAND:

D: Deluxe

Goodman®

Brand

A: Amana®

Brand MAJOR

REVISION:

A:Initial Release

MINOR

REVISION:

A: Initial Release

ELECTRICAL:

1: 208-230V/1ph/60Hz

3: 208-230v/3ph/60Hz

4: 460v/3ph/60Hz

NOMINAL

CAPACITY:

024: 2 Tons

036: 3 Tons

048: 4 Tons

060: 5 Tons

COMMUNICATION

FEATURE:

C: 4-wire

Communication

Ready

PRODUCT IDENTIFICATION

The model number is used for positive identification of component parts used in manufacturing. Please use this number

whenrequestingserviceorpartsinformation.

* Indicates minor revision & is not used for order entry or inventory management

ASXC160241A*

ASXC160361A*

ASXC160481A*

ASXC160601A*

ASXC160241B*

ASXC160361B*

ASXC160481B*

ASXC160601B*

The United States Environmental Protection Agency (“EPA”) has issued various regulations re-

garding the introduction and disposal of refrigerants introduced into this unit. Failure to follow

these regulations may harm the environment and can lead to the imposition of substantial fines.

These regulations may vary by jurisdiction. Should questions arise, contact your local EPA office.

WARNING

Do not connect or use any device

that is not design certified by

Goodman for use with this unit.

Serious property damage, personal injury, reduced unit

performance and/or hazardous conditions may result

from the use of such non-approved devices.

WARNING

WARNING To prevent the risk of property

damage, personal injury, or death,

do not store combustible materials or use gasoline or

other flammable liquids or vapors in the vicinity of this

appliance.

WARNING

DSXC160241A*

DSXC160361A*

DSXC160481A*

DSXC160601A*

DSXC160481B*

DSXC160601B*

PRODUCT DESIGN

Modelscovered by this manualcomewithanew4-wirecom-

municatingPCB. When paired with a compatiblecommuni-

cating indoor unit and a communicating thermostat, these

modelscansupport4-wirecommunicationprotocolandpro-

videmoretroubleshootinginformation.Thesemodelsarealso

backwardcompatible with the legacythermostat wiring.

*SXC16 models are available in 2, 3, 4 and 5 ton sizes and

use R-410A refrigerant. They are designed for 208/230 volt

singlephaseapplications.

The condenser air is pulled through the condenser coil by a

direct drive propeller fan. This condenser air is then dis-

charged out of the top of the cabinet.

These units are designed for free air discharge, so no addi-

tional resistance like duct work shall be attached.

The suction and liquid line connections on present models

areofthe sweat type for field piping withrefrigeranttypecop-

per. Front seating valves are factory installed to accept the

fieldruncopper. The total refrigerantcharge for a normal in-

stallation is factory installed in the condensing unit. *SXC

units are charged for the matching evaporator coil and a 15

footrefrigerantlineset.

Systems should be properly sized by heat gain and loss

calculations made according to methods of the Air Condi-

tioning Contractors Association (ACCA) or equivalent. It is

the contractors responsibility to ensure the system has ad-

equate capacity to heat or cool the conditioned space.

*SXC16 models use the Copeland Scroll "Ultratech" Series

compressorswhichare specifically designed for R-410Are-

frigerant. Thereare anumberofdesign characteristics which

are different from the traditional reciprocating and/or scroll

compressors.

"Ultratech" Series scroll compressors with Copeland®

ComfortAlert diagnostics will not have a discharge thermo-

stat, some of the early model scroll compressors required

dischargethermostats.

Due to their design Scroll compressors are inherently more

tolerantofsmall quantities of liquid refrigerant.

NOTE: Eventhough the compressorsectionofaScroll com-

pressor is more tolerant of liquid refrigerant, continued

floodback or flooded start conditions may wash oil from the

bearingsurfacescausing premature bearing failure.

"Ultratech" Series scroll compressors use "POE" or

polyolesteroil whichis NOT compatiblewithmineraloilbased

lubricants like 3GS. "POE" oil must be used if additional oil

isrequired.

WARNING

To avoid possible injury, explosion or death, practice

safe handling of refrigerants.

Operating pressures and amp draws may differ from stan-

dardreciprocatingand/orscroll compressors. This informa-

tion may be found in the "Cooling Performance Data" sec-

tion.

This unit is for outdoor installation only. Refer to figure for

minimum clearances from the sides of the unit to full walls

andother objects.

NOTE: This unit cannot be completely enclosed. At least

one side must be unrestricted.

Theseclearanceswillhelpavoidairrecirculation.Ifinstalling

two or more units at the same location, allow at least 24

inches between units. If only one side is restricted (for ex-

ample, against the outside wall of a house), the unit may be

placed as close as 8" to that one wall.

DO NOT locate the unit:

* Directlyundera vent termination fora gas appliance.

* Within 3 feet of a clothes drier vent

* Wheretherefreezingofdefrostwaterwould create

ahazard

* Where water may rise into the unit.

OK!

AA AAA

CCOK!

OK!

NOT

RECOMMENDED

AA AA

B B B

Model Type A B C AA

Residential 10" 10" 18" 20"

Light Commercial 12' 12" 18" 24"

CONDENSING UNIT SPECIFICATIONS

NOTE: This data is provided as a guide, it is important to electrically connect the unit and properly size fuses/circuit breakers and

wires in accordance with all national and/or local electrical codes. Use copper wire only.

Unit specifications are subject to change without notice. ALWAYS refer to the unit's serial plate for the most up-to-date general

and electrical information.

Model Dimensions - W x Dx H

*SXC160241A* 29 x29 x32¼

*SXC160361A* 29 x29 x38¼

*SXC160481A* 35½ x35½ x38¼

*SXC160601A* 35½ x35½ x38¼

A/DSXC160241A* - A/DSXC160601A*

* Up to 24' in equivalent line length

(1) Wire size should be determined in accordance with National Electrical Codes; extensive wire runs will require larger wire sizes.

(2) Maximum Overcurrent Protection Device: MUST use Time Delay Fuse or HACR type Circuit Breaker of the same size as noted.

NOTES:

• Always check the S & R plate for electrical data on the unit being installed.

• Installer will need to supply 7/8" to 1-1/8" adapters for suction line connections (4 & 5 ton units).

• Installer will need to supply 3/4" to 7/8" adapters for suction line connections (3 ton unit).

• Unit is charged with refrigerant for 15' of 3/8" liquid line. System charge must be adjusted per Installation Instructions Final Charge

Procedure.

• Installation of these units requires the specified TXV Kit to be installed on the indoor coil. THE SPECIFIED TXV IS DETERMINED BY THE

OUTDOORUNIT,NOTTHEINDOORCOIL.

Dimensions

*SXC160241A* *SXC16036A* *SXC160481A* *SXC160601A*

Cooling Capacity, BTUH 24,000 36,000 48,000 60,000

Compressor

R.L. Amps 10.3 16.7 21.2 25.6

L.R. Amps 52.0 82.0 96.0 118.0

Low Pressure Switch

Open 22 PSIG 22 PSIG 22 PSIG 22 PSIG

Close 50 PSIG 50 PSIG 50 PSIG 50 PSIG

High Pressure Switch

Open 610 PSIG 610 PSIG 610 PSIG 610 PSIG

Close 420 PSIG 420 PSIG 420 PSIG 420 PSIG

Condenser Fan Motor

Horsepower 1/12 1/6 1/6 1/6

F.L. Amps 0.6 1.0 1.0 1.0

Liquid Line, Inches O.D.* 3/8" 3/8" 3/8" 3/8"

Suction Line, Inches O.D.* 3/4" 7/8" 1-1/8" 1-1/8"

Refrigerant Charge 137.0 157.0 202.0 197.0

Power Supply 208/230-60-1 208/230-60-1 208/230-60-1 208/230-60-1

Minimum Circuit Ampacity(1) 13.5 21.9 27.5 33.0

Maximum Overcurrent Device(2) 20 35 45 50

Electrical Conduit Size

Power Supply (Inches) 1/2 or 3/4 1/2 or 3/4 1/2 or 3/4 1/2 or 3/4

Approximate Shipping Weight 282 282 296 296

A/DSXC160[24-60]1A*

CONDENSING UNIT SPECIFICATIONS

NOTE: This data is provided as a guide, it is important to electrically connect the unit and properly size fuses/circuit

breakers and wires in accordance with all national and/or local electrical codes. Use copper wire only.

ASXC160[24-36]1B*

Dimensions

* Up to 24' in equivalent line length

(1) Wire size should be determined in accordance with National Electrical Codes; extensive wire runs will require larger wire sizes.

(2) Maximum Overcurrent Protection Device: MUST use Time Delay Fuse or HACR type Circuit Breaker of the same size as noted.

NOTES:

• Always check the S & R plate for electrical data on the unit being installed.

• Installer will need to supply 7/8" to 1-1/8" adapters for suction line connections (4 & 5 ton units).

• Installer will need to supply 3/4" to 7/8" adapters for suction line connections (3 ton unit).

• Unit is charged with refrigerant for 15' of 3/8" liquid line. System charge must be adjusted per Installation Instructions Final Charge

Procedure.

• Installation of these units requires the specified TXV Kit to be installed on the indoor coil. THE SPECIFIED TXV IS DETERMINED BY THE

OUTDOORUNIT,NOTTHEINDOORCOIL.

Model Dimensions - Wx D x H

ASXC160241B* 29 x 29 x 30¼

ASXC160361B* 29 x 29 x 30¼

ASXC160241BB ASXC160241BC ASXC160361BB ASXC160361BC

Cooling Capacity, BTUH 24,000 24,000 36,000 36,000

Compressor

R.L. Amps 10.3 11.7 16.7 15.3

L.R. Amps 52.0 58.3 82.0 83.0

Low Pressure Switch

Open 22 PSIG 22 PSIG 22 PSIG 22 PSIG

Close 50 PSIG 50 PSIG 50 PSIG 50 PSIG

High Pressure Switch

Open 610 PSIG 610 PSIG 610 PSIG 610 PSIG

Close 420 PSIG 420 PSIG 420 PSIG 420 PSIG

Condenser Fan Motor

Horsepower 1/6 1/6 1/6 1/6

F.L. Amps 1.1 1.1 0.9 0.9

Liquid Line, Inches O.D.* 3/8" 3/8" 3/8" 3/8"

Suction Line, Inches O.D.* 3/4" 3/4" 7/8" 7/8"

Refrigerant Charge 100.0 88.0 110.0 96.0

Power Supply 208/230-60-1 208/230-60-1 208/230-60-1 208/230-60-1

Minimum Circuit Ampacity(1) 14.0 15.7 21.8 20.0

Maximum Overcurrent Device(2) 20 20 35 35

Electrical Conduit Size

Power Supply (Inches) 1/2 or 3/4 1/2 or 3/4 1/2 or 3/4 1/2 or 3/4

Approximate Shipping Weight 198 198 202 202

CONDENSING UNIT SPECIFICATIONS

NOTE: This data is provided as a guide, it is important to electrically connect the unit and properly size fuses/circuit breakers and

wires in accordance with all national and/or local electrical codes. Use copper wire only.

Unit specifications are subject to change without notice. ALWAYS refer to the unit's serial plate for the most up-to-date general

and electrical information.

Model Dimensions - Wx D x H

ASXC160481B* 35½ x 35½ x 36¼

ASXC160601B* 35½ x 35½ x 38¼

* Upto24'inequivalentline length

(1) Wire size should be determined in accordance with National Electrical Codes; extensive wire runs will require larger wire sizes.

(2) Maximum Overcurrent Protection Device: MUST use Time Delay Fuse or HACR type Circuit Breaker of the same size as noted.

NOTES:

• Always check the S & R plate for electrical data on the unit being installed.

• Installer will need to supply 7/8" to 1-1/8" adapters for suction line connections (4 & 5 ton units).

• Installer will need to supply 3/4" to 7/8" adapters for suction line connections (3 ton unit).

• Unit is charged with refrigerant for 15' of 3/8" liquid line. System charge must be adjusted per Installation Instructions Final Charge

Procedure.

• Installation of these units requires the specified TXV Kit to be installed on the indoor coil. THE SPECIFIED TXV IS DETERMINED BY THE

OUTDOORUNIT,NOTTHEINDOORCOIL.

Dimensions

ASXC160[48-60]1B*

ASXC160481B* ASXC160481BC ASXC160601B* ASXC160601BC

Cooling Capacity, BTUH 48,000 48,000 60,000 60,000

Compressor

R.L. Amps 21.2 21.2 25.6 28.8

L.R. Amps 96.0 104.0 118.0 152.9

Low Pressure Switch

Open 55 PSIG 55 PSIG 22 PSIG 22 PSIG

Close 95 PSIG 95 PSIG 50 PSIG 50 PSIG

High Pressure Switch

Open 610 PSIG 610 PSIG 610 PSIG 610 PSIG

Close 420 PSIG 420 PSIG 420 PSIG 420 PSIG

Condenser Fan Motor

Horsepower 1/6 1/6 1/6 1/6

F.L. Amps 1.0 1.2 1.0 1.2

Liquid Line, Inches O.D.* 3/8" 3/8" 3/8" 3/8"

Suction Line, Inches O.D.* 1 1/8" 1 1/8" 1 1/8" 1 1/8"

Refrigerant Charge 135.0 135.0 200.0 200.0

Power Supply 208/230-60-1 208/230-60-1 208/230-60-1 208/230-60-1

Minimum Circuit Ampacity(1) 27.5 27.7 33.0 37.2

Maximum Overcurrent Device(2) 45 45 50 60

Electrical Conduit Size

Power Supply (Inches) 1/2 or 3/4 1/2 or 3/4 1/2 or 3/4 1/2 or 3/4

Approximate Shipping Weight 241 241 301 301

CONDENSING UNIT SPECIFICATIONS

NOTE: This data is provided as a guide, it is important to electrically connect the unit and properly size fuses/circuit

breakers and wires in accordance with all national and/or local electrical codes. Use copper wire only.

DSXC160241AB DSXC160241AC DSXC160361AB DSXC160361AC

Cooling Capacity, BTUH 24,000 24,000 36,000 36,000

Compressor

R.L. Amps 10.3 11.7 16.7 15.3

L.R. Amps 52.0 58.3 82.0 83.0

Low Pressure Switch

Open 22 PSIG 22 PSIG 22 PSIG 22 PSIG

Close 50 PSIG 50 PSIG 50 PSIG 50 PSIG

High Pressure Switch

Open 610 PSIG 610 PSIG 610 PSIG 610 PSIG

Close 420 PSIG 420 PSIG 420 PSIG 420 PSIG

Condenser Fan Motor

Horsepower 1/6 1/6 1/6 1/6

F.L. Amps 1.1 1.1 0.9 0.9

Liquid Line, Inches O.D.* 3/8" 3/8" 3/8" 3/8"

Suction Line, Inches O.D.* 3/4" 3/4" 7/8" 7/8"

Refrigerant Charge 100.0 88.0 110.0 96.0

Power Supply 208/230-60-1 208/230-60-1 208/230-60-1 208/230-60-1

Minimum Circuit Ampacity(1) 14.0 15.7 21.8 20.0

Maximum Overcurrent Device(2) 20 20 35 35

Electrical Conduit Size

Power Supply (Inches) 1/2 or 3/4 1/2 or 3/4 1/2 or 3/4 1/2 or 3/4

Approximate Shipping Weight 198 198 202 202

DSXC160[24-36]1A*

Dimensions Model Dimensions - W x D x H

DSXC160241A* 29 x 29 x 30¼

DSXC160361A* 29 x 29 x 30¼

* Up to 24' in equivalent line length

(1) Wire size should be determined in accordance with National Electrical Codes; extensive wire runs will require larger wire sizes.

(2) Maximum Overcurrent Protection Device: MUST use Time Delay Fuse or HACR type Circuit Breaker of the same size as noted.

NOTES:

• Always check the S & R plate for electrical data on the unit being installed.

• Installer will need to supply 7/8" to 1-1/8" adapters for suction line connections (4 & 5 ton units).

• Installer will need to supply 3/4" to 7/8" adapters for suction line connections (3 ton unit).

• Unit is charged with refrigerant for 15' of 3/8" liquid line. System charge must be adjusted per Installation Instructions Final Charge

Procedure.

• Installation of these units requires the specified TXV Kit to be installed on the indoor coil. THE SPECIFIED TXV IS DETERMINED BY THE

OUTDOORUNIT,NOTTHEINDOORCOIL.

CONDENSING UNIT SPECIFICATIONS

NOTE: This data is provided as a guide, it is important to electrically connect the unit and properly size fuses/circuit breakers and

wires in accordance with all national and/or local electrical codes. Use copper wire only.

Unit specifications are subject to change without notice. ALWAYS refer to the unit's serial plate for the most up-to-date general

and electrical information.

DSXC160[48-60]1B*

Dimensions Model Dimensions - W x D x H

DSXC160481B* 35½ x 35½ x 36¼

DSXC160601B* 35½ x 35½ x 38¼

* Upto24'inequivalentline length

(1) Wire size should be determined in accordance with National Electrical Codes; extensive wire runs will require larger wire sizes.

(2) Maximum Overcurrent Protection Device: MUST use Time Delay Fuse or HACR type Circuit Breaker of the same size as noted.

NOTES:

• Always check the S & R plate for electrical data on the unit being installed.

• Installer will need to supply 7/8" to 1-1/8" adapters for suction line connections (4 & 5 ton units).

• Installer will need to supply 3/4" to 7/8" adapters for suction line connections (3 ton unit).

• Unit is charged with refrigerant for 15' of 3/8" liquid line. System charge must be adjusted per Installation Instructions Final Charge

Procedure.

• Installation of these units requires the specified TXV Kit to be installed on the indoor coil. THE SPECIFIED TXV IS DETERMINED BY THE

OUTDOORUNIT,NOTTHEINDOORCOIL.

DSXC160481B* DSXC160481BC DSXC160601B* DSXC160601BC

Cooling Capacity, BTUH 48,000 48,000 60,000 60,000

Compressor

R.L. Amps 21.2 21.2 25.6 28.8

L.R. Amps 96.0 104.0 118.0 152.9

Low Pressure Switch

Open 55 PSIG 55 PSIG 22 PSIG 22 PSIG

Close 95 PSIG 95 PSIG 50 PSIG 50 PSIG

High Pressure Switch

Open 610 PSIG 610 PSIG 610 PSIG 610 PSIG

Close 420 PSIG 420 PSIG 420 PSIG 420 PSIG

Condenser Fan Motor

Horsepower 1/6 1/6 1/6 1/6

F.L. Amps 1.0 1.2 1.0 1.2

Liquid Line, Inches O.D.* 3/8" 3/8" 3/8" 3/8"

Suction Line, Inches O.D.* 1 1/8" 1 1/8" 1 1/8" 1 1/8"

Refrigerant Charge 135.0 135.0 200.0 200.0

Power Supply 208/230-60-1 208/230-60-1 208/230-60-1 208/230-60-1

Minimum Circuit Ampacity(1) 27.5 27.7 33.0 37.7

Maximum Overcurrent Device(2) 45 45 50 60

Electrical Conduit Size

Power Supply (Inches) 1/2 or 3/4 1/2 or 3/4 1/2 or 3/4 1/2 or 3/4

Approximate Shipping Weight 241 241 301 301

PERFORMANCE DATA ASXC160241A*-LOW STAGE

EXPANDED PERFORMANCE DATA COOLING OPERATION

MODEL: *SXC160241A* /CA*F3636C6** + TXV/ MBVC1200**-1**, Design Subcooling @AHRI 95°F Conditions,5°F @Serv. Vlv.

Outdoor Ambient Temperature

85 95 10

115

Entering Indoor Wet Bulb Temperature

IDB*

MBh 16.1 16.7 18.3 - 15.8 16.3 17.9 - 15.4 15.9 17.5 - 15.0 15.6 17.0 - 14.3 14.8 16.2 - 13.2 13.7 15.0 -

S/T 0.69 0.58 0.40 - 0.71 0.60 0.41 - 0.73 0.61 0.42 - 0.76 0.63 0.44

0.78 0.65 0.45

0.79 0.66 0.46

Delta T 19 17 13 - 20 17 13 - 20 17 13 - 20 17 13

20 17 13

18 16 12

525 KW 1.08 1.10 1.14 - 1.17 1.19 1.23 - 1.24 1.27 1.31 - 1.31 1.34 1.39

1.37 1.40 1.45

1.42 1.45 1.50

MPS 4.4 4.5 4.6 - 4.7 4.8 5.0 - 5.1 5.3 5.4 - 5.5 5.6 5.8

5.8 6.0 6.2

6.2 6.3 6.5

HI PR 223 240 244 - 252 271 275 - 287 309 313 - 327 352 357

368 396 401

412 443 449

LO P

119 123 134 - 123 127 138 - 127 131 143 - 130 134 147

133 137 150

136 140 153

MBh 17.5 18.1 19.8 - 17.1 17.7 19.4 - 16.7 17.3 18.9 - 16.3 16.8 18.5 - 15.4 16.0 17.5 - 14.3 14.8 16.2 -

S/T 0.71 0.60 0.41 - 0.74 0.62 0.43 - 0.76 0.63 0.44 - 0.78 0.65 0.45

0.81 0.68 0.47

0.82 0.68 0.47

Delta T 19 17 13 - 19 17 13 - 19 17 13 - 20 17 13

19 17 13

18 16 12

70 600 KW 1.09 1.11 1.15 - 1.18 1.20 1.24 - 1.25 1.28 1.33 - 1.32 1.35 1.40

1.38 1.41 1.46

1.43 1.47 1.52

MPS 4.4 4.5 4.7 - 4.8 4.9 5.0 - 5.2 5.3 5.5 - 5.5 5.7 5.8

5.9 6.0 6.2

6.2 6.4 6.6

HI PR 226 243 246 - 255 274 278 - 290 312 316 - 330 355 360

372 400 405

416 447 454

LO P

120 124 136 - 124 128 140 - 128 132 144 - 132 136 148

134 138 151

137 142 155

MBh 18.0 18.7 20.4 - 17.6 18.2 20.0 - 17.2 17.8 19.5 - 16.7 17.4 19.0 - 15.9 16.5 18.1 - 14.7 15.3 16.7 -

S/T 0.75 0.63 0.43 - 0.78 0.65 0.45 - 0.80 0.66 0.46 - 0.82 0.69 0.48

0.85 0.71 0.49

0.86 0.72 0.50

Delta T 18 16 12 - 19 16 12 - 19 16 12 - 19 16 12

18 16 12

17 15 11

675 KW 1.10 1.12 1.16 - 1.19 1.21 1.25 - 1.26 1.29 1.34 - 1.33 1.37 1.41

1.39 1.43 1.48

1.44 1.48 1.53

MPS 4.5 4.6 4.7 - 4.8 4.9 5.1 - 5.2 5.3 5.5 - 5.6 5.7 5.9

5.9 6.1 6.3

6.3 6.4 6.6

HI PR 228 245 248 - 258 277 281 - 293 315 319 - 334 359 364

375 404 409

420 452 458

LO P

122 125 137 - 125 129 141 - 129 133 146 - 133 137 150

135 140 153

139 143 156

MBh 16.416.918.319.616.016.517.919.215.616.117.418.715.3 15.7 17.0 18.2 14.5 14.9 16.2 17.3 13.4 13.8 15.0 16.1

S/T 0.78 0.70 0.53 0.34 0.81 0.73 0.55 0.35 0.83 0.74 0.56 0.36 0.86 0.77 0.58 0.37 0.89 0.80 0.60 0.39 0.90 0.80 0.61 0.39

DeltaT22211712232117122321171223 21 17 12 23 21 17 12 21 19 16 11

525 KW 1.08 1.10 1.14 1.18 1.17 1.19 1.23 1.27 1.24 1.27 1.31 1.36 1.31 1.34 1.39 1.44 1.37 1.40 1.45 1.50 1.42 1.45 1.50 1.56

MPS 4.4 4.5 4.6 4.8 4.7 4.8 5.0 5.2 5.1 5.3 5.4 5.6 5.5 5.

5.8 6.0 5.8 6.0 6.2 6.4 6.2 6.3 6.5 6.8

HI PR 223 240 244 249 252 271 275 281 287 309 313 320 327 352 357 364 368 396 401 410 412 443 449 459

LO P

119 123 134 143 123 127 138 147 127 131 143 152 130 134 147 156 133 137 150 159 136 140 153 163

MBh 17.818.319.821.317.417.919.320.816.917.418.920.316.5 17.0 18.4 19.8 15.7 16.2 17.5 18.8 14.5 15.0 16.2 17.4

S/T 0.81 0.73 0.55 0.35 0.84 0.75 0.57 0.37 0.86 0.77 0.58 0.38 0.89 0.80 0.60 0.39 0.92 0.83 0.63 0.40 0.93 0.83 0.63 0.41

DeltaT22201712222117122221171223 21 17 12 22 20 17 12 21 19 16 11

75 600 KW 1.09 1.11 1.15 1.19 1.18 1.20 1.24 1.29 1.25 1.28 1.33 1.37 1.32 1.35 1.40 1.45 1.38 1.41 1.46 1.51 1.43 1.47 1.52 1.57

MPS 4.4 4.5 4.7 4.8 4.8 4.9 5.0 5.2 5.2 5.3 5.5 5.7 5.5 5.

5.8 6.1 5.9 6.0 6.2 6.4 6.2 6.4 6.6 6.8

HI PR 226 243 246 251 255 274 278 284 290 312 316 323 330 355 360 368 372 400 405 414 416 447 454 464

LO P

120 124 136 144 124 128 140 149 128 132 144 154 132 136 148 158 134 138 151 161 137 142 155 165

MBh 18.318.820.421.917.918.419.921.417.518.019.420.917.0 17.5 19.0 20.4 16.2 16.7 18.0 19.3 15.0 15.4 16.7 17.9

S/T 0.85 0.76 0.58 0.37 0.88 0.79 0.60 0.38 0.90 0.81 0.61 0.39 0.93 0.84 0.63 0.41 0.97 0.87 0.66 0.42 0.98 0.87 0.66 0.43

DeltaT21201611212016112220161122 2

16 11 21 20 16 11 20 18 15 10

675 KW 1.10 1.12 1.16 1.20 1.19 1.21 1.25 1.30 1.26 1.29 1.34 1.38 1.33 1.37 1.41 1.46 1.39 1.43 1.48 1.53 1.44 1.48 1.53 1.58

MPS 4.5 4.6 4.7 4.9 4.8 4.9 5.1 5.3 5.2 5.3 5.5 5.7 5.6 5.

5.9 6.1 5.9 6.1 6.3 6.5 6.3 6.4 6.6 6.9

HI PR 228 245 248 254 258 277 281 287 293 315 319 326 334 359 364 372 375 404 409 418 420 452 458 468

LO P

122 125 137 146 125 129 141 150 129 133 146 155 133 137 150 159 135 140 153 162 139 143 156 166

* EnteringIndoor DryBulbTemperature NOTE: Shadedarea is ACCA(TVA) conditions KW=Total system power

h and low

ressures are measured atthe li

uid and suction service valves.

MPS=outdoor unit am

(

com

.+fan

)

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Bomba de calor de Goodman

Goodman

Goodman GPH1336M43 Series Manual de usuario

Goodman

Goodman Condencing Unit Manual de usuario

Goodman

Goodman CONDENSING UNIT HEAT PUMP Manual de usuario

Goodman

Goodman DSX16 Manual de usuario

Goodman

Goodman IO-259U Manual de usuario

Goodman

Goodman CPC036XXX3BXJXBA Manual de uso y cuidado

Goodman

Goodman PH 15 SEER Series Manual de usuario

Goodman

Goodman CPLE090 Manual

Goodman

Goodman GPH13H Manual de usuario

Goodman

Goodman SSZ 14 SEER Manual de usuario

Goodman

Goodman SS-CPKF50 SS-CPKF50 Instrucciones de instalación

Goodman

Goodman GSZ 14 SEER Manual de usuario

Goodman

Goodman ASX Instrucciones de funcionamiento

Goodman

Goodman GPH 13 M Series Manual de usuario

Goodman

Goodman GSZ140311 Manual de usuario

Goodman

Goodman GPH13 Instrucciones de funcionamiento

Goodman

Goodman SSZ 14 SEER Manual de usuario

Goodman

Goodman SSZ 16 SEER Documento técnico

Goodman

Goodman CONDENSING UNIT Manual de usuario

Goodman

Goodman SS-GSH10C Manual de usuario

Goodman

Goodman DSX18 Manual de usuario

Goodman

Goodman GSZ16 Manual de usuario

Goodman

Goodman GPH1324M41AB Manual de uso y cuidado

Goodman

Goodman GSH 10 SEER Manual de uso y cuidado

Manuales populares de Bomba de calor de otras marcas

MICROWELL

MICROWELL HP 1000 GREEN Manual de usuario

Sanyo

Sanyo SAP120FCH Manual de usuario

Daikin

Daikin EHYHBH05AA Manual de usuario

Panasonic

Panasonic WH-SDF03E3E5 Guía

Bryant

Bryant 544B Manual de usuario

Airxcel

Airxcel 45000 Series Manual

Mitsubishi Electric

Mitsubishi Electric PUZ-SWM60VAA Manual de usuario

Dimplex

Dimplex LI 16I-TUR Guía del usuario

Carrier

Carrier WSHP Open v3 Guía de configuración rápida

TGM

TGM CTV14CN018A Manual de usuario

Carrier

Carrier 38MGQ Series Manual de usuario

Kokido

Kokido K2O K880BX/EU Guía de solución de problemas

Viessmann

Viessmann VITOCAL 300-G PRO Type BW 2150 Guía rápida

Carrier

Carrier 48EZN Manual de usuario

Viessmann

Viessmann KWT Vitocal 350-G Pro Series Instrucciones de funcionamiento

Ariston

Ariston NIMBUS Manual de usuario

Weishaupt

Weishaupt WWP L 7 Guía del usuario

GE Zoneline AZ85H09EAC Manual de usuario