Gold Note B-5.1 Manual de usuario
B-5.1
PRECISION TONEARM
USER MANUAL
2
DESCRIPTION AND SPECIFICATIONS
..........................................................................................................................
INSTALLATION
...........................................................................................................................................................
OVERVIEW AND ANTI-SKATING
..................................................................................................................................
VTA AND AZIMUTH
...................................................................................................................................................
WARRANTY AND SERVICE..................................................................................................................................
TROUBLESHOOTING..........................................................................................................................
IMPORTANT SAFETY INFORMATION...................................................................................................................
P. 3
P. 5
P. 6
P. 7
P. 8
P. 9
P. 10
INDEX
DESCRIPTION AND SPECIFICATIONS
B-5.1 is an elegant high-performance tonearm completely designed and handmade in Italy with the greatest attention to
details to achieve maximum precision and to deliver the truly best sonic results.
The B-5.1 is powered by high-precision micro ball-bearings made in Germany by GRW -exclusively manufactured for Gold
Note - singularly sealed and packed to preserve their perfect integrity.
The B-5.1’s effective length of 242mm with a 19mm overhang makes it easy to install on any turntable.
The tonearm features a double counterweight for perfect set up adjustment for virtually all phono cartridges.
Optionally, extra weights are available to handle phono cartridges of higher mass.
The B-5.1 ultra precisely engineered tonearm will bring to life your favorite music getting natural, extra detailed and
refined audio performances.
3
SPECIFICATIONS
Typology: 9” Ball Bearing Tonearm
Overhang: 19mm
Offset: 24°
Arm wand: straight aluminum 6000 alloy
Inserting Plinth Shaft: 23mm
Dynamic effective mass: 10g
VTF: 0.186N (19g)
VTA: adjustable on collar
Lift: hydraulic
Anti-skating: wire/5 positions
Anti-skating force: from the center to the outside the effect is 0.5g each step = 0.5 - 1.0 - 1.5 - 2.0 - 2.5
Azimuth: adjustable on the headshell
CABLES
Internal cables: AWG36 Hyper Litz shielded 99,99% OFC
External cable supplied: 1,5m custom 4 pole DIN/RCA
DIMENSIONS AND WEIGHT
Effective length: 242 mm
Weight: 195g without counterweight
FINISHES
Shell and pivot: Black anodised Aluminium
Arm wand: Black anodised Aluminium
Counterweight: Stainless Steel
Hydraulic lift board: Black
DESCRIPTION AND SPECIFICATIONS
4
5
INSTALLATION
STEP 1
Insert the tonearm into the arm collar on the turntable and block it with the hex-bolts on the collar while adjusting the
VTA (requires the cartridge to be already installed).
Insert the Phono Cable into the arm collar of the turntable as suggested in the picture. Insert the arm into the base and
then proceed to screw the 3 grains arranged on the external circumference at intervals of 120 °.
STEP 2
Connect the Phono Cable to the tonearm.
To align the female DIN connector of the tonearm to the male
DIN connector of the cable correctly refer to the ground slot.
1
2
3
4
1
2
+_
1-ANTI-SKATING nylon wire with bullet counterweight
3
2
4
- ANTI-SKATING adjustment bar
- TONEARM COUNTERWEIGHT: to set up the correct tracking force depending on the phono cartridge in use
- SHELL AZIMUTH ADJUSTMENT: to adjust the alignment of the tonearm head-shell (0,9mm Allen Wrench)
INSTALLING THE ANTI-SKATING SYSTEM
1- Slip the loop of the ANTI-SKATING nylon wire over the groove of the ADJUSTMENT BAR
2- Feed the wire through the loop of the SUPPORT HOOP
3- Adjust the ANTI-SKATING force choosing the correct groove on the ADJUSTMENT BAR
6
OVERVIEW AND ANTI-SKATING
3
7
VTA AND AZIMUTH
VTA SETUP
Loose the Hex
-bolt indicated by the arrow on the collar using
the 1,5mm Allen Wrench supplied to lift up or down the arm
correctly adjusting the VTA as necessary.
Allen-key 1,5 mm
Arm board
AZIMUTH
After the cartridge has been properly installed on the tone arm,
adjust the Azimuth of the shell with the supplied 0,9mm Allen
Wrench.
Setting a correct Azimuth will provide a better audio
performance.
Allen-key 0,9 mm
WARRANTY AND SERVICE
WARRANTY
To validate the warranty is necessary to register the unit on the Gold Note internet web site within 15 days from the
purchase on the appropriate area of the web site: www.goldnote.it/warranty
If the unit is not registered correctly or has been purchased from a different country of the purchaser home address
the unit will not be covered by any warranty and the registration will be refused.
The warranty does not cover in any case: Tubes, Phono Cartridge Stylus and Batteries.
SERVICE
Every GOLD NOTE® product is the result of meticulous technological research, and consequently their correct
functioning is guaranteed. In spite of this it is possible that problems may emerge which non-specialist users cannot
resolve.
In this case, contact your dealer to be advised on how the fault can be solved.
Do not return any object directly to the factory or to the distributor without being authorised to do so.
In such cases both GOLD NOTE® and the distribution agents decline responsibility of any kind.
For more information please visit www.goldnote.it/service
PLEASE NOTE
Descriptions and technical characteristics may vary at any time and without notice.
8
9
For spare parts visit the official Gold Note store at:
TROUBLESHOOTING
FAQ
ACTION DESCRIPTION HOW TO ADJUST IT
CLEANING THE UNIT • Use EXTREME care and ONLY very soft cotton
cloth to clean the unit.
Any acid will irreversibly damage the unit fine
finishes.
Do not use any alcohol to clean the unit. Only
dry cloth is allowed.
SYMPTOM DESCRIPTION CAUSE REMEDY
SPEAKER HUMMING
PROBLEMS
• The tone arm is not correctly
grounded.
The speakers hum
when the cable is
connected to the
amplifier.
• The cartridge connectors are not
well inserted.
• The Ground DIN connector slots
do not touch each other.
• Verify the cartridge connectors
are well inserted.
• Be sure the DIN slot contacts touch
each other well.
• Adjust the Azimuth of the Head-Shell
with the supplied 0,9mm Allen Wrench
as described in the specific chapter of
this manual.
• The interconnect input and/or
output cables of the amplifiers are
not shielded.
• Be sure the Phono Cable DIN
Connector is well inserted in the tone
arm female DIN.
• Be sure to always use shielded
cables for the amp connections.
TONE ARM TRACKS BAD The Headshell is bent.
The Vertical Tracking
Angle of the arm is
wrong.
• Adjust the VTA moving the arm shaft by
loosing the three hex-bolts placed on the
edge on the arm board collar with the
help of the 1,5mm Allen Wrench supplied.
http://www.akamaiaudio.it/
TROUBLESHOOTING
Otros manuales para B-5.1
2
Tabla de contenidos
Otros manuales de Placa giratoria de Gold Note
Gold Note
Gold Note Vasari Series Manual de usuario
Gold Note
Gold Note Shibata Manual de usuario
Gold Note
Gold Note Bellagio Conquest Manual de usuario
Gold Note
Gold Note Machiavelli Gold MKII Manual de usuario
Gold Note
Gold Note PIANOSA Manual de usuario
Gold Note
Gold Note MEDITERRANEO X Manual de usuario
Gold Note
Gold Note VASARI RED Manual de usuario
Gold Note
Gold Note VALORE 425 Lite Manual de usuario
Gold Note
Gold Note VALORE Plus 425 Manual de usuario
Gold Note
Gold Note Bellagio Reference Manual de usuario
Gold Note
Gold Note VALORE Plus 425 Manual de usuario
Gold Note
Gold Note VALORE 425 Lite Manual de usuario
Gold Note
Gold Note GIGLIO Manual de usuario
Gold Note
Gold Note MACHIAVELLI RED MKII Manual de usuario
Gold Note
Gold Note ES78 Manual de usuario
Gold Note
Gold Note B-5.1 Manual de usuario
Gold Note
Gold Note Machiavelli Red Manual de usuario
Gold Note
Gold Note VALORE Plus 425 Manual de usuario
Gold Note
Gold Note VALORE Plus 425 Manual de usuario
Gold Note
Gold Note VALORE 425 Lite Manual de usuario
