Glunz & Jensen PlateWriter 2000 Manual de usuario

Pre-installation Manual

PlateWriter™ 2000

Pre-installation Manual

PlateWriter™ 2000

Edition AC, December 2011

This book has part No. 51591

T11125

This manual is published by: GLUNZ & JENSEN A/S

Selandia Park 1

DK-4100 Ringsted

Denmark

Phone:+45 57 68 81 81

E-mail: [email protected]

Internet: www.glunz-jensen.com

Pre-installation Manual - PlateWriter™ 2000 0746

0-2

Table of contents

1036 Pre-installation Manual - PlateWriter™ 2000

Table of contents 0-3

Part 1: Introduction .................................... 1-1

About this manual ................................................1-1

Intended use of this manual .......................................1-1

Reservations ..................................................1-1

Important ......................................................1-1

Unintended use of the equipment....................................1-1

Installation ...................................................1-1

Notes, cautions, and warnings ! .......................................1-2

Part 2: When the crates arrive ............................2-1

Storing the crates .................................................2-1

Crate dimensions and weights ......................................2-1

Checking for damage ............................................2-1

Transporting the crates .............................................2-2

Handling the crates .............................................2-2

Lifting the crates ...............................................2-2

Available doorway width for transport .................................2-2

Part 3: Site requirements ................................ 3-1

General requirements ..............................................3-1

Environmental requirements .......................................3-1

Cleaning facilities ...............................................3-1

Space requirements ...............................................3-2

PlateWriter dimensions ...........................................3-2

Free space around the PlateWriter ...................................3-3

RIP workstation ..................................................3-4

Location .....................................................3-4

Network connection .............................................3-4

Power supply ....................................................3-5

Main power connection...........................................3-5

Power outlet requirements.........................................3-6

Power consumption .............................................3-6

Power cables ..................................................3-7

Part 4: Pre-installation checklist ...........................4-1

Pre-installation Manual - PlateWriter™ 2000 0746

Table of contents

0-4

Part 1: Introduction

About this manual

Intended use of this manual

•This manual describes how to prepare the installation site for the installation of the

PlateWriter 2000 System. The procedures described in this manual require a

reasonable level of technical skill and access to the proper tools.

Reservations

•This manual was written and illustrated using the best possible information

available at the time of publication.

•Any differences between this manual and the equipment reflect improvements

introduced after the publication of the manual.

•Changes, technical inaccuracies and typographical errors will be corrected in

subsequent editions.

•As a part of our policy of continuous improvement, we reserve the right to alter

design and specifications without further notice.

Important

Unintended use of the equipment

Glunz & Jensen A/S do not take any responsibility for any damage or accidents caused

by unintended use of the equipment:

•As the equipment is certified by accredited test laboratory (UL International Demko

A/S) it is absolutely prohibited to make any modifications, electrical nor mechanical,

of the equipment. If however this prohibition is disregarded, Glunz & Jensen's

warranty will no longer apply and the certification labels for UL, C-UL, and

CE certification of the equipment shall be removed as the certification will no longer

apply to the equipment.

Installation

•Never install the equipment in explosive environments.

•It is the responsibility of the owner and operator/s of the equipment, that the

installation is made in accordance with local regulations, and by engineers

authorized to carry out electrical installations.

•Installation must be performed only by service technicians who are trained in

installing the equipment.

•The manufacturer cannot be held responsible for any damage caused by incorrect

installation of this equipment.

1036 Pre-installation Manual - PlateWriter™ 2000

Introduction 1-1

About this manual

Notes, cautions, and warnings !

Throughout the manual notes, cautions, and warnings are written in bold like the

example below:

"The cover can only be positioned on the finishing unit if the front cover is not

in place.

Symbol Meaning Explanation

"Note

The operator should observe and/or act according to the

information in order to obtain the best possible function of

the equipment.

$Caution

The operator must observe and/or act according to the

information in order to avoid any mechanical or electrical

damage to the equipment.

#Warning

The operator must observe and/or act according to the

information in order to avoid any personal injury.

Pre-installation Manual - PlateWriterTM 2000 0746

Introduction

1-2 Important

Part 2: When the crates arrive

Storing the crates

The crates containing the PlateWriter System will usually arrive some time before the

arrival of the Service Technician. In such a case you should prepare an appropriate

place indoors to store the crates.

Crate dimensions and weights

Below are the dimensions and weights of the crates included with the delivery:

LxWxH Weight

Imaging unit (1) 1000 x 800 x 720 mm

(39.4 x 31.5 x 28.4")

55 kg

(121 lb)

Finishing unit, ink dryer etc. (2) 1910 x 940 x 1030 mm

(75.2 x 37.0 x 40.6")

216 kg

(476 lb)

Checking for damage

When receiving the crates do the following:

•Check if the crates are damaged at the time of delivery.

•Report any damage to the crate(s) to the transport company.

•Take notes of the damage before you unpack the crates. Provide a detailed

description and/or take a photograph of the damage.

1036 Pre-installation Manual - PlateWriter™ 2000

When the crates arrive 2-1

Storing the crates

Dryer Unit

Understel

Curing Unit

Finisher Unit

Tables + Alignment Mat

Ink Dryer

RIP Workstation

T31751

Transporting the crates

Handling the crates

The icons on the crates indicate how to handle them during transport and storage:

Lifting the crates

To lift the crates, at least a fork-lift truck or two persons and a hand-powered pallet

mover are required.

Available doorway width for transport

If the width of the door(s) through which the crates have to be transported to the

installation site are too narrow, you will have to unpack the crates and transport all

parts to the installation site separately.

"Two or more persons are required for this operation.

Pre-installation Manual - PlateWriter™ 2000 0746

When the crates arrive

2-2 Transporting the crates

T31691

Ensure that the side

indicated by the

arrows is always up.

Handle the

crate with care.

Never expose the crate to

water, or place it in a

high-humidity area.

Otros manuales para PlateWriter 2000

Tabla de contenidos

Otros manuales de Impresora de Glunz & Jensen

Glunz & Jensen

Glunz & Jensen PlateWriter 2000 Manual de usuario

Glunz & Jensen

Glunz & Jensen PlateWriter 3000 Manual de usuario

Glunz & Jensen

Glunz & Jensen PlateWriter 8000 Manual de usuario

Glunz & Jensen

Glunz & Jensen Flex-In-One 260 Manual de usuario

Glunz & Jensen

Glunz & Jensen Concept 205 C Manual de usuario

Glunz & Jensen

Glunz & Jensen PlateWriter 3600 Pro Manual de usuario

Glunz & Jensen

Glunz & Jensen PlateWriter 2000 Manual de usuario

Glunz & Jensen

Glunz & Jensen PlateWriter 2500 Manual de usuario

Glunz & Jensen

Glunz & Jensen PlateWriter 3600 Pro Manual

Glunz & Jensen

Glunz & Jensen PlateWriter 2000 Manual de usuario

Glunz & Jensen

Glunz & Jensen MultiLine 950 Manual de usuario

Glunz & Jensen

Glunz & Jensen InterPlater MD 85 Thermal Manual de usuario

Glunz & Jensen

Glunz & Jensen PlateWriter 3000 Manual de usuario

Glunz & Jensen

Glunz & Jensen MultiLine 950 Manual de usuario

Glunz & Jensen

Glunz & Jensen PlateWriter 2000 Manual de usuario

Glunz & Jensen

Glunz & Jensen PlateWriter 8000 Manual

Glunz & Jensen

Glunz & Jensen PlateWriter 3000 Manual de usuario

Manuales populares de Impresora de otras marcas

Lexmark

Lexmark 1400 Series Manual

Canon

Canon i70 Series Manual de usuario

Evolis

Evolis Elypso Manual de usuario

Kyocera

Kyocera FS-9530DN Manual de usuario

Canon

Canon LASER SHOT LBP-1210 Manual de usuario

Samsung

Samsung BIXOLON SRP-350plusF Manual de usuario

Canon

Canon PIXMA PRO-1 Series Manual de usuario

Canon

Canon PIXMA G3560 Guía de configuración

Dell

Dell Color Laser Printer 2130cn Manual de usuario

Tektronix

Tektronix Phaser 840 Manual de usuario

Epson

Epson ET-7750 Instrucciones de funcionamiento

Canon

Canon CLBR 460ps Manual de usuario

Eltron

Eltron P210 Guide Manual de usuario

Ricoh

Ricoh MD-P1 Manual de usuario

Epson

Epson SC-F7100 series Manual de usuario

Epson

Epson Stylus C40UX Manual de usuario

Canon

Canon imagePASS-A2 Manual de usuario

Canon

Canon S820D Manual de usuario