Glorystar TAD321-A Manual de usuario
Android Advertising
Displayer
TAD321-A
User Manual
Please read this instruction before
This device has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
device generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to
radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this device does cause harmful interference to radio or television
reception, which can be determined by turning the device off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the device and receiver.
--Connect the device into an outlet on a circuit different from that to which the
receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help
Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment
FCC Radiation Exposure Statement The antennas used for this transmitter must be in
stalled to provide a separation distance of at least 20 cm from all persons and must
not be co-located for operating in conjunction with any other antenna or transmitter.
Importation Safety Instructions
Read this user manual
All safety and operating instructions in this user manual should be read before operating the
product
Keep this user manual
This user manual should be retained for future references.
Head Warnings
Be cautious about warning signals on the product.
Follow Instructions
Please follow instructions in this user manual
Attachments
To avoid danger, please do not use attachments not recommended by the product
manufacturer.
Mounting
Do not place the product on any unstable cart, stand, tripod or table to avoid injury on
children and adult. Please only use attachments indicated by product manufacturer.
Temperature
Please use this product within operating temperature 32°F ~ 100°F (0°C ~ 45°C), relative
humidity 20%-80%. The product should be situated away from any heat source such as
radiators, heat registers, stoves or other products (including amplifier) to product heat.
Avoid Liquid Invasion
Avoid the invasion of any liquid. Avoid placing it near bathtub, sink, kitchen, wet basement or
swimming pool. Do not place product on any uneven surfaces and keep a distance of at least 6
inches from wall. Do not place heavy objects on top of the unit and at sealed areas to avoid
heat ventilation problems.
Product Protection
Please do not place any attachment or parts inside the product to avoid contacts with voltage
points that could result an electric shock or fire.
Heat Ventilation
There is no heat ventilation on the upper and lower part of the product, therefore to avoid
overheating, please do not block any ventilation openings with objects (e.g. carpet). Please
allow the opening to have 10cm distance for ventilation.
Grounding or Polarization
This product could be equipped with an alternate plug.
Power –Cord Protection
Power supply cords should be routed so that they are unlikely to be walked on or pitched by
items placed upon them. Pay attention to the connection of plugs.
Power Sources
This product should be operated only from the typeof power source indicated on the rear
panel. If you are unsure of the type of power supply to your home, consult your product
purchaser or local power company.
Lighting and storms
Unplug the outlet during lighting, storms or long unused periods. This will prevent damages
and power-line surges to the product.
Overloading
Do not overload wall outlets, extension cords or integral convenience receptacles as this can
result in a risk of fire or electric shock.
Damage Handling
Unplug this product from the outlet of wall and request qualified service personnel under the
following conditions:
• when the power supply cord or plug is damaged
• when the picture display gets dimmer
• when liquid has been spilled or objects have fallen on to the product
• when the product has been exposed to rain or water.
• Adjust only those controls that are in the instruction manual. For improper adjustments may
result in damage and will often require extensive work by a qualified technician to restore
the product to its normal operation.
• When the product exhibits a distinct change in performance-this indicates a need for repair
service.
Replacement parts
When replacement parts are required, be sure that the technician uses replacement parts
specified by the manufacturer or parts with same features. Unauthorized substitution may
result in fire, electric shock or other hazards.
Safety Check
Upon completion of any service or repair to this product, ensure technician for proper
operating condition performs safety checks.
Warnings
If the battery of remote control is incorrectly replaced, there will be a danger of explosion.
Storage
Keep the product at dim areas, room temperature and low humidity to maintain original
condition. This will avoid danger.
Transportation
Since the product consists of glass and delicate electronic components, excessive shock or
drop will result damages. Please handle the product carefully to minimize shock during
transportation.
Recycling
The product utilizes tin-lead solder, and has a fluorescent lamp containing a small amount of
mercury. For environmental considerations, disposal of these materials may be regulated in
your community. For disposal or recycling information, please contact your local authorities,
or Electronics Industries Alliance: http://www.eiae.org/
Cleaning
Unplug the product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol
cleaners. Use damp cloth for cleaning.
Spec. & Package
Package included:
-Please confirm all the items is included before the setup start.
Model TAD321-A
Sizes 32”
Resolution
(pixles)
1920x1080
Brightness 700 cd/m2
Aspect Ratio 16:9
CPU Dual-core Cortex-A72 up to 1.8GHz Quad-core Cortex-A53 up to 1.4GHz
RAM 4 GB LPDDR4
Operating System Android 9
Hardware Support Earphone, RJ45, Wi-Fi,BT, TYPE-C,USB,HDMI
Speaker 5Wx2
Memory Support SD Card
Introduction of Android
1. Start up and shut down
To start your device,put ACplug into AC jack,and push key to light up the screen. To
shut down your device,pull-out AC plug from AC jack.
2. The App Drawer – right top corner
Press in the bottom of the screen from down to up to open the App Drawer. The
“Apps” tab displays all applications that are available on the tablet.
To place a app shortcut on the desktop, touch and hold the icon until the App Drawer
fades and the desktop appears. Move your finger to the location where you want to place
the icon and release your touch to place the icon.
When using apps or other parts of the operating system you often will see the “Extra
Options” icon.
Pressing this icon will open a secondary menu with more options. Functions like opening
an advanced setting menu, switching to a different account or refreshing the displayed
information are often “Hidden” behind this icon.
3. Navigation icons – bottom of the screen
On the bottom side you will find icons: Use the navigation icons “Home”
Or “Return” to close the App Drawer and return to your desktop. The “Recent
Activity” icon will show an interview of the active and recently opened applications.
Click on the small displayed preview to open that application.
General Operation
1. Installation of Applications
You can install your own Apps by opening the Apps shop. This button can be found in the
screen. Note that not all applications may function properly for your tablet. Some are made
especially for small screen devices such as phones.
You can also install your own Apps by opening the File Manager with SD card. You can find
the File Manager in the “App drawer＂too. And please follow the below steps:
1)Copy the APK file to your SD memory card and insert the card into your Jarvis.
2)Open the File Manager and click the SD card icon.
3)Open the APK and click on the install button.
4)It will show the installing blocked because it is not from Apps store｀Google Play’ and then
please accept the permission.
5)The application is now installed.
2. Administer/remove apps
The｀Apps＇item in the｀Setting＇menu will display an overview of the installed apps.
There are four tabs available which filter the displayed app list. Select an app to view its
detailed information.
3. Add an account
The best way to fully make use of your Android tablet is by linking your Google/Gmail
account to your device. Open the｀Settings＇menu and choose the｀Accounts & sync＇
item.
Without any added accounts the right pane will display nothing. Instead select the option｀
Add account＇in the top right corner. To add a Google/Gmail account please select｀Google
＇in the pop-up and follow the instructions on the screen. After entering your Google
username and password you have the option to automatically back-up your apps, setting (i.e.
bookmarks and Wifi passwords) and other data.
Tabla de contenidos
Otros manuales de Monitor de Glorystar
