Globel 6' Wide Manual de usuario
GARDEN SHED
Assembly Instructions
Suitable for Models
6'Wide 8'Wide 10'Wide
© Globel Industries Pty Ltd
GI00034 September 1 2014
WITH VARYING DEPTHS
Choking Hazard - This product contains small parts.
It's Not That Difficult!
IMPORTANT! Read These Instructions FIRST.
The construction of your shed isn't as complicated as it may first appear.
Our step by step, illustrated instructions are easy to follow, and we provide hints
to make the assembly even easier. Simply follow our recommendations and carefully study
our illustrations, then your garden shed will be assembled quickly and accurately.
Make sure the site you choose for your garden shed is firm and level, and water drains away from the site.
Do not install the garden shed in areas subject to high winds.
Do not assemble the garden shed on a windy day.
Your garden shed should be assembled on a specifically prepared base, ie concrete slab or pavers (or a suitable
Garden Shed Foundation Kit) and then secured using the recommended dyna bolts as listed in the "Tools Required" page.
A heavy duty polythene sheet should be placed under the foundation to assist in reducing rising dampness from the soil,
thus reducing condensation build up in your garden shed.
Once secured, we highly recommend applying silicone along the inside of the base rail to prevent water from seeping under
the base frame and into your shed.
Do not backfill against the shed's walls or base, as this will cause corrosion and void the warranty.
Check the labelling on the Parts Cartons to ensure you have the shed model you ordered, and the correct
number of Parts Cartons.
For simplicity, in most part, this manual illustrates the construction of a 6' wide garden shed, with additional
instructions for 8' and 10' wide garden sheds inserted where applicable.
TOOLS INFORMATION:
The tools you need are shown in the "TOOLS REQUIRED" section.As all the holes for screws and nuts and bolts are
pre-drilled, you will only need a power screw driver or a cordless drill with a magnetic Phillips-head tip to make
the assembly quicker and easier.
Do not over-tighten self-tapping screws.
Nuts can be tightened by holding your finger on them as you tighten the bolt with the power screw driver -
no spanner needed.
CHECK THE PARTS:
Before you start, separate and identify all the parts and hardware. (Refer to Parts List diagrams in the following pages).
WARNING: Edges are sharp - Handle with care.
WE RECOMMEND you get a second pair of hands to assist you with the assembly.
INSTALLATION ADVICE
Garden Shed Specifications -
Examples of specific shed sizes listed - will vary for other sizes
SHED TYPE / SIZE BASE DIMENSIONS
(Front x Sides mm) ROOF DIMENSIONS
(Front x Sides mm) WALL SHEET
HEIGHT
mm Sides Pitch
OVERALL HEIGHT
mm DOOR OPENING
(Height x Width mm) No. CARTONS
(Weight Kg)
Size (Feet)Type
Double Sliding Doors 6 x 5 1710 x 1440 1840 x 1540 1780 1790 1700 x 625 1 (56)1930
Double Sliding Doors 8 x 6 2340 x 1750 2455 x 1850 1780 1790 1700 x 1050 2 (73)1980
Double Sliding Doors 10 x 8 2950 x 2370 3070 x 2470 1780 1790 1700 x 1050 2 (100)2020
© Globel Industries Pty Ltd
GI00034 September 1 2014 1
TOOLS REQUIRED
Step Ladder
Masonry Drill Bit
6.5mm
Tape Measure
Phillips-Head
Screw Driver Bit
(P2)
Battery Power Drill
Dyna Bolts
(not supplied)
6.5mm x 36mm
recommended
© Globel Industries Pty Ltd
GI00034 September 1 2014 2
PARTS LIST
CARTON '2' - (8' wide & 10' wide models only)
4
6
-
2
4
-
2
4
1
2 of each
2
2
4
7
4
2
4
2
2
4
1
2 of each
2
2
4
12
2
2
6
2
2
4
1
2 of each
2
2
1
1
1
1
1
1
2
1
2
2
2
-
2
1
1
1
1
1
1
1
2
1
2
2
2
-
2
1
1
1
1
1
1
1
2
1
2
2
2
2
2
1
QTY QTY QTY
6' x 5'
MODEL
8' x 6'
MODEL
10' x 8'
MODEL
Base Rail (Front)
Base Rail (Back)
Side Base Rail (Left)
Side Base Rail (Right)
Front Mid-Wall Brace (Left)
Front Mid-Wall Brace (Right)
Side Mid-Wall Brace
Back Mid-Wall Brace
Side Top-Wall Rail
Top Rail - (Front & Back)
Roof Beam
Mid Roof Beam
Side Roof Trim
Entry/Exit Ramp
Corner Panel
Wall Sheet (Full)
Wall Sheet (Half)
Door Jamb
Roof Sheet (Full)
Roof Sheet (Half)
Door
Roof Starter
Above Door Fascia
Door Brace (Top & Bottom)
Gable (Left)
Gable (Right)
SPECIFIC TO 3 SIZES LISTED
Roof Corner Cap
Corner Brace
Left Top-Wall Rail Bracket
Right Top-Wall Rail Bracket
Door Glide
Door Glide Roller
Door Spacer
Gable Name Plate
Door Handle
Screws
Nuts
Bolts
Washers
Left Mid Roof Beam Bracket
Right Mid Roof Beam Bracket
4
6
2
2
4
16
4
2
2
1 x bag
1 x bag
1 x bag
YES
-
-
4
6
2
2
4
16
4
2
2
1 x bag
1 x bag
1 x bag
YES
-
-
4
6
2
2
4
16
4
2
2
1 x bag
1 x bag
1 x bag
YES
2
2
HARDWARE KIT
NOTE: Hardware Kit is packed in Carton '1' for all models
NOTE:
Carton '2' parts as listed below for 6' wide models are packed in Carton '1'.
(This refers to all 6' wide models with a depth not exceeding 6').
2 2 2
Roof Cap (Standard)
- 1 3
Roof Cap (Short)
3
CARTON '1'
*Quantity will vary depending on depth of shed
*Quantity will vary depending on depth of shed
- - 2
Roof Strut
© Globel Industries Pty Ltd
GI00034 September 1 2014
PARTS LIST - Hardware Kit
WASHERS
SCREW BOLT NUT
GABLE NAME PLATE
CORNER BRACE
LEFT
TOP-WALL RAIL
BRACKET
RIGHT
TOP-WALL RAIL
BRACKET
DOOR GLIDE DOOR SPACER
DOOR ROLLER
ROOF
CORNER CAP
DOOR HANDLE
MID ROOF BEAM
BRACKETS
(10' WIDE SHED ONLY)
LEFT RIGHT
4
CHOKING HAZARD -
This product contains small parts.
WARNING
© Globel Industries Pty Ltd
GI00034 September 1 2014
ABOVE DOOR FASCIA DOOR BRACE
PARTS LIST - Carton '1'
CORNER
PANEL
FULL
WALL SHEET HALF
WALL SHEET DOOR JAMB
(6' WIDE
SHED ONLY)
DOORDOOR JAMB
(8' & 10' WIDE
SHEDS ONLY)
ROOF STARTER
RIGHT GABLELEFT GABLE
RIGHT GABLE
(10' WIDE SHED ONLY)
LEFT GABLE
(10' WIDE SHED ONLY)
NOTE: 8' wide shed gables not shown
NOTE:
Hole configurations shown
are for 6' wide sheds
(unless otherwise noted).
8' and 10' wide sheds will have
varying hole configurations.
HALF
ROOF SHEET
FULL
ROOF SHEET
5
© Globel Industries Pty Ltd
GI00034 September 1 2014
NOTE:
Hole configurations shown
are for 6' wide sheds
(unless otherwise noted).
8' and 10' wide sheds will have
varying hole configurations.
FRONTAND BACK
TOP RAIL
ENTRY/EXIT RAMP
FRONT
BASE RAIL
LEFT
SIDE BASE RAIL
RIGHT
SIDE BASE RAIL
LEFT FRONT MID-WALL
BRACE
RIGHT FRONT MID-WALL
BRACE
SIDE
TOP-WALL RAIL
BACK
MID-WALL BRACE
BACK
BASE
RAIL
SIDE
MID-WALL BRACE
ROOF
BEAM
PARTS LIST - Carton '2'
MID ROOF BEAM
(10' WIDE SHED
ONLY)
6
SIDE
ROOF TRIM
STANDARD ROOF CAP SHORT ROOF CAP
ROOF STRUT
(ONLY)
10' WIDE SHED
© Globel Industries Pty Ltd
GI00034 September 1 2014
FORMWORK
FORMWORK
FOUNDATIONS
Your shed requires a solid foundation.
If you need to construct a concrete slab, this page shows the method and dimensions we recommend.
Make sure the slab area is square
by ensuring diagonal corner dimensions
are equal.
(Diagram B)
Formwork
must be100mm thick and level. (Diagram C)
First, lay builders plastic on the ground as a
barrier to rising moisture. (Diagram D)
Then place F52 reinforcing steel mesh on top of
the builders plastic, ensuring the steel mesh is
raised off the plastic to a depth of approximately
half the thickness of the formwork. (Diagram E)
Then pour the concrete and allow five days to cure.
ROOF WIDTH
SLAB WIDTH
ROOF
DEPTH SLAB
DEPTH
SLAB DIMENSIONS
100mm
100mm
Diagram A
Determine the size of the concrete slab
by adding 100mm to the width and 100mm
to the depth of the roof size of the shed.
(See Diagram A).
Adding the additional 100mm prevents
rainwater from the roof creating a trench,
and splashing soil against the walls of the
shed, which could cause corrosion.
A
B
C
MEASUREMENT 'X' = MEASUREMENT 'Y'
SLAB
AREA
X
Y
Y
X
Diagram B
Diagram C
FORMWORK
SPIRIT LEVEL
FORMWORK
BUILDERS
PLASTIC
Diagram D F52 REINFORCING
STEEL MESH
MESH RAISED TO
APPROXIMATELY HALF
THICKNESS OF FORMWORK
F52
REINFORCING
STEEL MESH
Diagram E
7
© Globel Industries Pty Ltd
GI00034 September 1 2014
Pre-Assembly
GABLES
Front and back gables assembly:
Attach the gables to a top rail
by sliding the gable bottom
flange under the protruding
flange of the top rail.
Secure using three
screws per gable,
along the top edge
of the rail as shown
in Diagram 1.
Note:
Diagram shown is 6' wide shed.
8' wide shed: use four screws per gable.
10' wide shed: use five screws per gable.
(i)
(You will be making two gable assemblies)
(ii)
(iii) Repeat for other top rail and gables.
Join the two gables together by
inserting a nut and bolt in each of
the BOTTOM two holes in the
side flanges as shown in Diagram 2.
Diagram 2
SIDE
FLANGE
BOTTOM
2 HOLES
LEAVE
TOP HOLE
EMPTY
ON ALL
MODELS
6' Wide Shed
LEAVE
TOP HOLE
EMPTY
LEAVE
BOTTOM HOLE
EMPTY
LEAVE
TOP HOLE
EMPTY
10' Wide Shed8' Wide Shed
Diagram 1
GABLE GABLE
FLANGE ON
TOP RAIL
FLANGE ON
GABLE
TOP
RAIL
6' Wide Shed
8
© Globel Industries Pty Ltd
GI00034 September 1 2014
Attach two mid beam brackets to
the gable assembly as shown, and
secure using two nuts and bolts in
each. See Diagram 3.
Repeat for other gable assembly,
using the remaining two mid beam brackets.
(i)
(ii)
Pre-Assembly
GABLES - 10' wide shed only:
IMPORTANT:
Study diagrams and brackets to ensure correct
brackets are used at each side.
Left
Mid Beam
Bracket
Right
Mid Beam
Bracket
Gable
Gable
Diagram 3
9
© Globel Industries Pty Ltd
GI00034 September 1 2014
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
