Gira System 3000 Manual de usuario

System 3000

Presence and motion detector 360° top unit BT

Order no.: 5377 02

Operating instructions

1 Safety instructions

Electrical devices may only be mounted and connected by electrically skilled persons.

Serious injuries, fire or property damage possible. Please read and follow manual fully.

Danger of electric shock. Always disconnect before carrying out work on the device or load. In

so doing, take all the circuit breakers into account, which support dangerous voltages to the

device and or load.

Danger of electric shock. The device is not suitable for disconnection from supply voltage. De-

pending on the insert used, the load is not electrically isolated from the mains, even when the

device is switched off.

Do not press on the sensor window. Device can be damaged.

The device is not suitable for use as a burglar alarm or other alarm.

These instructions are an integral part of the product, and must remain with the end customer.

2 Device components

Figure1: Device components

(1) FMinsert

(2) Sensor top

(3) Brightness sensor

(4) Button Bluetooth Ʃ

(5) Sensor window and status LEDs

(6) Decor ring

(7) Push-on cover

Status LED

Red LED lights up Self-test

Red LED flashes 3 s on / 3 s off Alarm function active

1 / 13

82599322 24.10.2019

System 3000

Presence and motion detector 360° top unit BT

Red LED flashes 0.5 s on / 0.5 s off Alarm was triggered

Red LED flashes three times followed by a 1 s

pause

Cover was previously connected to another in-

sert

Yellow LED lights up "Off" or "Off for 0.5 - 5 hours" function active

Yellow LED flashes Presence simulation active

Green LED lights up "On" or "On for 0.5 - 5 hours" function active

Blue LED lights up Device is coupled with a mobile end device

and active app

Blue LED flashes 0.5 s on / 0.5 s off Bluetooth coupling mode active

3 Intended use

– Automatic switching of lighting depending on the heat motion and ambient brightness

– Operation with flush-mounted insert for dimming or switching or 3-wire extension

– Ceiling installation on flush-mounted insert.

Product characteristics

Functions directly on the cover

– Extension of the detection area in combination with 3-wire extension

– Operation with 2-wire or 3-wire extension, rotary dimmer extension or push-button

– Dimming light via extension with dimming insert

– Resetting to factory setting

– Push-on cover for limiting the detection field

Functions via app

– Setting the device as presence detector or motion detector

– Setting the brightness threshold

– Separate adjustment of the sensitivity of the three PIR sensors

– Setting the run-on time

– Continuous ON, Continuous OFF

– Timer ON or OFF for 0.5 - 5 hours

– Switch-off pre-warning

– Dynamic run-on time

– Presence simulation

– Alarm function

– Timer function

– Walking test

In combination with a switch insert

– Short time operation

In combination with a dimming insert

– Switch on with last saved brightness or saved switch-on brightness

– Adjusting the minimum brightness

– Adjusting the maximum brightness

– Basic light function

– Night light function

– Constant light regulation

Automatic operation

The device detects heat motions of people, animals and objects.

2 / 13

82599322 24.10.2019

System 3000

Presence and motion detector 360° top unit BT

– The light is switched on if a person enters the detection field and the brightness threshold

is below the set brightness threshold.

– The run-on time restarts with each detected motion.

– The light is switched off, if:

no more movement is detected in the detection field and the run-on time has elapsed or

the ambient light is too bright and the run-on time has elapsed.

To avoid any switch-on caused by a cooling illuminant, no movement signals are evaluated for a

brief lockout time after switching off. The motion detector adjusts itself to the ambient conditions

to keep the time as short as possible.

Behaviour after a mains voltage failure

After mains voltage return, the device performs a self-test for a maximum of 20 seconds. After

the self-test has been completed, the device is ready for operation.

If the red status LED flashes three times at repeated intervals, the cover was previously

connected to another insert. To enable the function again, either place the cover onto the

respective insert or press the Bluetooth button (4) for longer than 4 seconds.

The following applies during the self-test:

– The red status LED is illuminated.

– The load is switched off.

– Movements are not detected

– The device can be operated via extensions

4 Commissioning

Install app on a mobile end device

Requirement for operation via app is a mobile end device with Bluetooth interface, running the

Android operating system or iOS.

￭ Download and install the Gira System 3000 app from the iTunes App Store (iOS) or the

Google Play Store (Android).

Couple mobile end devices via Bluetooth

Precondition: insert and cover must be ready for operation. The mobile end device is located

close to the cover.

￭ Activate coupling mode: Press the Bluetooth Ʃ button (4) (Figure 1) for more than 4

seconds.

The blue LED flashes. The coupling mode is active for one minute.

￭ Start the app and search for device to be coupled.

Cover is coupled with the end device and shown in the app.

The coupling mode is automatically exited after successful coupling. The blue LED lights

up to confirm an active connection.

A maximum of 8 mobile end devices can be coupled with a cover. When coupling the 9th

device, the oldest device will be deleted.

5 Operation

The app is used for the configuration and operation of the device. Some basic functions can

also be operated via connected extensions.

Operation using 2-wire or 3-wire extension with button cover or push-button

Multiple extensions can be combined with each other. All operations described here are also

possible via the app. Operation with the rotary dimmer extension is described in the rotary dim-

mer extension instructions.

3 / 13

82599322 24.10.2019

System 3000

Presence and motion detector 360° top unit BT

Switching on light for the duration of the run-on time

Short-time operation: When pressed, pulses are generated approx. every 3 seconds for 1

minute. Exception for 3-wire extension: only one pulse is generated.

￭ Press the button cover or push-button briefly.

Motion detector operation: If the button cover or push-button is pressed again after

switching on, the run-on time is restarted. In combination with a dimming insert, switch-on

brightness is switched on again.

Switching the light off for 3 minutes

This function can only be used in presence detector operation.

￭ Press the button cover at the bottom or push-button briefly.

The light is switched off for the period of 3 minutes. When movements are detected, the

time is restarted.

Adjust the brightness, only in combination with dimming insert

￭ Long press on button cover at the top or bottom or push-button.

Save switch-on brightness, only in combination with dimming insert

￭ Adjust the brightness.

￭ Press the button cover over entire surface for longer than 4 seconds.

An push-button cannot be used to save the switch-on brightness.

Delete switch-on brightness, only in combination with dimming insert

￭ Press the button cover briefly: Light switches on at the saved switch-on brightness.

￭ Press the button cover over the entire surface for longer than 4 seconds: Switch-on

brightness is deleted. Switching on takes place at the last brightness value set.

A push-button cannot be used to delete the switch-on brightness.

6 Information for electrically skilled persons

DANGER!

Mortal danger of electric shock.

Disconnect the device. Cover up live parts.

Detection field and range

The device has a detection field of 360°. The diameter of the detection field depends on the in-

stallation height and the direction of motion of persons in the detection field. The detection field

becomes larger the greater the installation height, while the detection density and sensitivity are

reduced at the same time.

4 / 13

82599322 24.10.2019

System 3000

Presence and motion detector 360° top unit BT

Figure2: Detection range depending on the direction of movement

Diameter of detection field for direction of movement

Installation height 1: 2: 3: 4:

2.20 m 14.50 m 11.50 m 8.00 m 6.00 m

2.50 m 16.50 m 13.00 m 10.00 m 7.00 m

3.00 m 20.00 m 16.00 m 12.00 m 8.00 m

3.50 m 23.00 m 18.50 m 14.00 m 9.00 m

4.00 m 26.00 m 17.00 m 14.50 m *) – *)

5.00 m 28.00 m 18.00 m 15.00 m *) – *)

6.00 m 29.00 m 19.00 m – *) – *)

1: Range for tangential movement on the ground

2: Range for radial movement on the ground

3: Range for typical movements at desks, e.g. torso movement

4: Range of fine detection at desks, e.g. mouse movements

*) When used as a presence detector: Installation height should not be more than 3.5

m, otherwise fine detection is not possible.

Selecting installation location

For use as a presence detector, the device is installed, for example, above a workplace and

monitors the surface below it. For use as a motion detector, the device is installed, for example,

in the hallway.

￭ Select a vibration-free installation location. Vibrations can lead to unwanted switching.

￭ Avoid interference sources in the detection area. Interference sources can trigger the mo-

tion detector, e.g. heat sources such as heating units, outlets from ventilation openings or

air conditioners, copiers, printers, coffee machines, draughty doorways, animals etc.

The detection field can be limited in order to minimise the influence of interference

sources. For this, use the push-on cover (see Limiting the detection field using the push-

on cover) or switch off individual sensors (see Configuring device settings).

Aligning cover

The device has three independent sensors for motion detection. The arrangement of the areas

A, B and C is clearly evident under the decor ring (Figure 4).

5 / 13

82599322 24.10.2019

System 3000

Presence and motion detector 360° top unit BT

Figure3: Detection field: areas A, B and C; installation height 2.20 m

Figure4: Arrangement of the areas A, B and C

￭ Pay attention to correct alignment when mounting the appliance box and flush-mounted

insert.

￭ Align the cover so that the brightness sensor is on the side away from the windows. This

reduces the effects of scattered light.

Fitting the cover

￭ Connect flush-mounted insert properly and mount in accordance with the desired orienta-

tion of the cover (see instructions for flush-mounted insert).

￭ Fit the cover on the flush-mounted insert

￭ Switch on mains voltage.

If the red status LED flashes three times at repeated intervals, the cover was previously

connected to another insert. If the cover is to remain on the insert, press the Bluetooth

button (4) for longer than 4 seconds.

6 / 13

82599322 24.10.2019

System 3000

Presence and motion detector 360° top unit BT

Limiting the detection field using the push-on cover

The push-on cover can be used to limit the detection field, e.g. in order to mask out interference

sources.

Figure5: Push-on cover

Size Range on the ground (mounting height 3 m)

Complete push-on cover Ø approx. 4.5 m

Area I cut out Ø approx. 7.5 m

Areas I + II cut out Ø approx. 12 m

without push-on cover Ø approx. 20 m

￭ Pull off push-on cover.

￭ Using scissors, cut out push-on cover along the marked lines as required.

￭ Push on push-on cover.

Alternatively, the detection field can also be limited via the app by reducing the sensitivity

or switching off individual sensors.

Expanding the detection field

To expand the detection field, connect a 3-wire extension with presence or motion detector

cover. The main device also evaluates signals of the extension and, if necessary, switches the

lighting on.

Configuring device settings

Settings are configured via the app

Default settings

Function Setting

Operating mode Motion detector

Operating mode Automatic operation

7 / 13

82599322 24.10.2019

System 3000

Presence and motion detector 360° top unit BT

Function Setting

Sensitivity of sensors A-C 100 %

Detection angle 360°, sensors A-C active

Brightness threshold 10lux

Run-on time 2 minutes

Supplementary function switched-off

Checking detection field

Any motions detected are displayed in the app and by the red LED. The lighting is switched on

for approx. 1 second. If the light is not to be switched dependent on motion, the Continuous ON

or Continuous OFF function should also be activated.

3-wire extension: detected motions are sent to the main device. This switches according

to its settings.

￭ Activate the walking test via the app and pace off the detection field. The function is auto-

matically terminated after approx 5 minutes.

Restoring the device to factory settings

After resetting the device to the default setting, it has to be removed from the app. On iOS

equipment, the device also has to be removed from the list of paired Bluetooth devices

(Settings/Bluetooth). Otherwise, re-pairing will not be possible.

￭ Briefly disconnect the device from the mains voltage.

Red LED lights up, self-test runs.

￭ Within 1 minute after switching on the mains voltage, press the Bluetooth Ʃ button for

longer than 20 seconds.

At the conclusion of the self-test or after 4 seconds, the blue LED flashes slowly. Coupling

mode is active; keep the Bluetooth Ʃ button pressed. After approx. 20 seconds, the blue

LED goes out and the red LED flashes quickly.

￭ Within 10 seconds, release the Bluetooth Ʃ button and press briefly once again.

The red LED flashes more slowly, device is reset to the factory settings and restarts.

7 Technical data

Ambient temperature -5 ... +45 °C

Storage/transport temperature -25 ... +70 °C

Dimensions Ø×H 103 × 66 mm

Installation height 3 m

Detection area Ø approx. 20 m (installation height 3m)

Detection angle 360 °

Sensitivity 0, 25, 50, 75, 100%

Brightness threshold

Motion detector operation approx. 5 ... 500lx (and day operation)

Presence detector operation approx. 5 ... 1000lx (and day operation)

Short time operation

pulse duration approx. 0.5 s

pulse stop approx. 3 s

Bluetooth

Radio frequency 2.402 ... 2.480 GHz

Transmission capacity max. 2.5 mW, Class 2

8 / 13

82599322 24.10.2019

System 3000

Presence and motion detector 360° top unit BT

Transmitting range typ. 10 m

8 Parameter list

Adjustable parameter list via app

Depending on the insert, the following parameters can be changed with the app.

Settings for switch and dimming inserts

Parameters Setting options, default set-

ting

Explanation

Operating mode Motion detector operation

Presence detector opera-

tion

Default setting: motion de-

tector operation

Setting whether the device operates as a mo-

tion detector or presence detector.

Operating mode Automatic mode

Timer OFF

Timer ON

Continuous OFF, Continu-

ous ON

Default setting: automatic

mode

Automatic: The load is switched depending on

motion and brightness.

Continuous OFF or ON: The load is perman-

ently switched off or on.

Timer OFF or ON: The load is switched off or

on for the specified time. Afterwards, the

device is in automatic mode again.

Setting timer ON 0.5 - 5 hours

Default setting: 2 h

Time for which the load remains switched on

when the "Timer ON" function is activated.

Setting timer OFF 0.5 - 5 hours

Default setting: 2 h

Time for which the load remains switched off

when the "Timer OFF" function is activated.

Run-on time 10 s ... 60 min

Default setting: 2 min

The load remains switched on for this time,

even if no more motion is detected or the am-

bient light is bright enough.

Dynamic self-

learning run-on

time

On, Off

Default setting: Off

Dynamic self-learning run-on time On:

The device automatically determines a run-on

time within specified limits and dynamically

from detected motion. In so doing, the run-on

time is increased if presence continues or de-

creased if absence is detected. The maximum

run-on time is the set run-on time. The

shortest run-on time is 10 seconds. For run-on

times times from 5 minutes, the brief presence

detection function is also active.

Brightness

threshold

Motion detector:

5… 500 lx

Presence detector: 5…

1000 lx and day operation

Default setting: 10 lx

The load is switched on if the brightness value

falls below this value and if motion is detected.

9 / 13

82599322 24.10.2019

System 3000

Presence and motion detector 360° top unit BT

Parameters Setting options, default set-

ting

Explanation

Using the current

brightness

The current brightness can

be stored in a range of 5 to

500 lx or 1000 lx.

Sets the brightness threshold parameter in the

app to the current brightness.

Sensor sensitivity 0, 25, 50, 75, 100 %

Default setting: 100%

Individually adjust the sensitivity in 5 steps for

each sensor A–C.

To restrict the detection field, switch off indi-

vidual sensors. To do this, set the sensitivity to

0 %.

Reduced basic

sensitivity

On, Off

Default setting: Off

Reduced basic sensitivity On:

Reduced basic sensitivity for use in environ-

ments with interference sources.

Presence simula-

tion

On, Off

Default setting: Off

The function can only be activated after more

than 24 hours of time was saved. In automatic

mode, the times at which the lighting was

switched on are continuously saved. A max-

imum of 60 switching operations are saved

over a period of 24 hours. If more switching

operations take place, the oldest ones are

overwritten respectively. If the presence simu-

lation is activated, the lighting is switched on

at the saved times depending on the bright-

ness. Switch-off takes place after the run-on

time has elapsed. Detected motions prolong

the run-on time or the light is switched on de-

pending on brightness. Times are not saved.

The dynamic run-on time is not taken into ac-

count.

Activating the day

operation

On, Off

Default setting: Off

In the setting day operation the device oper-

ates independently of the brightness.

Activating the

walking test

On, Off

Default setting: Off

Function for checking the detection field. The

function automatically terminates after

5 minutes.

Activate alarm

operation

On, Off

Default setting: Off

This function is used to monitor an area for un-

authorised access during absence. If this is

the case, the lighting flashes (1 second on, 1

second off) for the duration of the run-on time.

In addition, a message is sent via the

Bluetooth interface. When motions are detec-

ted, the run-on time is restarted.

Time change On, Off

Default setting: On

Activates automatic summer/wintertime

changeover

Settings only for switch inserts

Parameters Setting options,

default setting

Explanation

Switch-off pre-

warning

On, Off

Default setting:

Off

If the switch-off pre-warning is activated, the light is not

switched off immediately after the run-on time has

elapsed. Triple flashing at an interval of 10 seconds

shows that the light will be switched off soon. The run-

10 / 13

82599322 24.10.2019

Otros manuales para System 3000

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Sensor de seguridad de Gira

Gira

Gira 0335 00 Manual de usuario

Gira

Gira 5373 Series Manual de usuario

Gira

Gira 2105 02 Manual de usuario

Gira

Gira 0318 04 Manual de usuario

Gira

Gira 2399 02 Manual de usuario

Gira

Gira 180 plus Manual de usuario

Gira

Gira Cube 120 Manual de usuario

Gira

Gira Tectiv 220 Manual de usuario

Gira

Gira System 3000 5373 Series Manual de usuario

Gira

Gira 2050 Series Manual de usuario

Gira

Gira System 3000 Manual de usuario

Gira

Gira Cube 240 2194 Series Manual de usuario

Manuales populares de Sensor de seguridad de otras marcas

THORLABS

THORLABS PDA10JT Manual de usuario

Waeco

Waeco UV-DETECT Manual de usuario

Intermatic

Intermatic IOS-DSIMF Manual de usuario

urmet domus

urmet domus 1083 Manual de usuario

Siemens

Siemens AZL66 Series Manual de usuario

BTI

BTI Profiline Multi Finder Manual de usuario

Challenger

Challenger SL01 Manual de usuario

DMP Electronics

DMP Electronics 1122INT Manual de usuario

Rielta

Rielta Ladoga MK-RK Manual de usuario

Mirion Technologies

Mirion Technologies ACCURAD PRD Manual de usuario

Bosch

Bosch DS835 Manual de usuario

DBI SALA

DBI SALA EZ Stop Manual del operador

Lamptime

Lamptime ST05C Manual de usuario

Ubiquiti

Ubiquiti MFI-MSC Manual de usuario

Subsite

Subsite 910R Instrucciones de instalación

Satel

Satel OPAL Pro Manual de usuario

Aleph

Aleph XC-1XTEU Manual de usuario

Pima

Pima LARIS QUAD Manual de usuario