Gigatrak Intermec CS40 Manual de usuario

Intermec CS40 Handheld Information

IntermecCS40HandheldInformation080511.doc Page1

Home Screen – View 1

Home Screen – View 2

Interacting with the Screen:

Touchscreen Calibration

If the touchscreen is not responding properly to stylus touch taps, the touchscreen may need to be

recalibrated.

1) Tap the Start > Settings > System > Screen

2) Follow the instructions on the screen

USE ONLY the STYLUS to complete the alignment.

Intermec CS40 Handheld Information

IntermecCS40HandheldInformation080511.doc Page2

Set Date/Time/Time Zone

1) Tap the Start button in the system tray.

2) Select “Settings”, then “Clock and Alarms”.

3) Set your time zone.

4) Set the current date, time.

5) OK to Exit.

Set Backlight Power

(The unit has an ambient light sensor, and will turn off when there is no activity.

Tap screen or press a key to resume)

1) Tap the Title bar at the top of the Home screen. Horizontal scroll bar appears under the Title bar.

2) Tap the Battery icon. Power screen appears.

3) From the horizontal scroll bar at the top, select Advanced

On Battery Power – Make your choices.. Turn off screen, check or uncheck box, Set Timer

On External Power – Make your choices..Turn off screen, check or uncheck box, Set Timer

. 4) Select OK at the bottom right of the screen to save.

Set Screen Brightness

1) Tap Start > Settings > System > Backlight

2) Adjust the slider to desired brightness

3) Check or uncheck box for “turn off backlight”… Set Timer”

4) Check or uncheck box for “turn on backlight” if button pressed, or screen tapped”

5) Tap OK at bottom right of the screen to save.

Check Power Settings

1) Start | Settings

2) Tap the Power icon – power settings display

Intermec CS40 Handheld Information

IntermecCS40HandheldInformation080511.doc Page3

Turn on ScanWedge

1) The ScanWedge Utility is active by default.

2) If the imager/scanner does not scan, it might be “disabled”.

3) To check the setting: Start > Settings > Systems > Intermec Settings > Data Collection >

Internal Scanner

4) “Enable scanner port” should be “on”…….

5) If not, Tap Enable Scanner Port , and check box to enable scanner.

6) Tap OK at bottom of screen to save setting.

Enable Barcode Symbology for Scanning:

1) While many typical barcode symbologies are enabled by default, others may need to be

enabled for particular applications.

2) To enable or configure barcode symbologies: Start > Settings > Systems > Intermec

Settings > Data Collection > Internal Scanner > Symbologies

3) Check and enable/configure the Symbologies required.

Append Carriage Return to Barcode scan

If the screen cursor does not advance to the next data field in your application after scanning a

barcode, you need to append a carriage return to the barcode scan.

Internal Scanner | Symbology Options | Post Amble

Intermec Settings Main Menu

2) Enter ”\x0D” for a Carriage Return

3) Tap OK at the bottom of the screen to Save your changes

Intermec CS40 Handheld Information

IntermecCS40HandheldInformation080511.doc Page4

Enable Wireless 802.11 (WiFi) Radio:

1) Tap: Start > Settings > Systems > Intermec Settings > Communications >802.11 Radio

> Radio Enabled

2) Select the Radio Enabled check box and Tap OK.

3) Use Intermec Settings to configure communication parameters (including security) for your

network.

Turn On/Off Bluetooth (opt 1):

1) Tap: Start > Settings > Connections | Wireless Center |

2) Tap Bluetooth to turn on/off the Bluetooth radio

3) Tap OK to close the wireless center

Turn On/Off & Configure Bluetooth (opt 2)

| Note: Reference the Intermec CS40 User’s Guide for specifics to connect to BT

devices.

Turning the Phone On and Off (Enable the phone):

1) From the Home Screen, Start | Settings | Connections | Wireless Center |

2) Tap Phone to turn on the Phone

3) Tap OK to close the wireless center

Intermec CS40 Handheld Information

IntermecCS40HandheldInformation080511.doc Page5

Make a Phone Call:

1) Press Phone from the Home screen (or) Tap the green phone key on the upper left side of

the keypad.

2) Tap the keys to enter the phone number you want to call

3) Tap Talk

Take a Picture:

1) Tap Start > Pictures & Video

2) Tap the Camera icon in the grid (or) the Camera button on the Title bar

3) Press Enter to take and save the picture.

Turn off the Terminal:

Press and hold the Power Button, at the upper right of the keypad (red phone icon on key

OR)

Select Start | Shutdown icon

Intermec CS40 Handheld Information

IntermecCS40HandheldInformation080511.doc Page6

APPENDIX 1 – Embedded Intermec Functions

iSpy WiFi v: Use iSpy WiFi to check 802.11 radio status and diagnose

connection issues.

Scan Diagnostic:

Use ScanDiagnostic application to diagnose problems with scanner.

Wireless Center:

Profile Settings:

Intermec Settings:

Intermec CS40 Handheld Information

IntermecCS40HandheldInformation080511.doc Page7

APPENDIX 2 –

Configure Wireless 802.11 Radio/ Security/Network

Enable Wireless 802.11 (WiFi) Radio:

4) Tap: Start > Settings > System > Intermec Settings > Communications >802.11 Radio >

Radio Enabled

5) Select the Radio Enabled check box and Tap OK.

6) Use Intermec Settings to configure communication parameters (including security) for your

network.

Select Wireless Security Choice for 802.11 (WiFi) Radio:

1) Tap: Start > Settings > System > Intermec Settings > Communications >802.11 Radio >

Security Choice

2) Select the Funk Security check box and Tap OK.

3) Use Intermec Settings to configure communication parameters (including security) for your

network.

Setup Wireless Security Choice for 802.11 (WiFi) Radio (If USING Static WEP):

1) Tap: Start > Settings > System > Intermec Settings > Communications >802.11 Radio >

Funk Security

2) Select the Profile 1. (or 2, 3 or 4 if adding additional Profiles)

3) Enter Profile Label (name)

4) Check radio Box for Network type:

a. Infrastructure for Access Points (this is the typical choice)

b Ad Hoc for PC to PC, or Device to Device, or Device to PC

5) Enter SSID (unique wireless network name)

6) Check radio Box for Power Mode: check CAM (for constant awake mode)

7) Select 802.1x security type (if used): none

8) Select Association: Open

9) Set Encryption: WEP

Define a value for the keys you want to use. You can define up to

four keys (Key 1 through Key 4).

Enter an ASCII key or a hex key that is either 5 bytes or 13 bytes long depending

on the capability of the radio. Set a 5- byte value for 64-bit WEP or a 13-byte value

for 128-bit WEP. Hex keys must be preceded by 0x and contain 5 or 13 hex pairs.

For Transmit key, if used, choose the key you want to use for transmitting

your data

10) The rest of the screen requires scrolling through to set any necessary security options.

If you don’t know what these are – contact the IT staff.

11) To Save your settings, Select OK at the bottom menu panel if no additional changes are

needed.

Intermec CS40 Handheld Information

IntermecCS40HandheldInformation080511.doc Page8

Setup Wireless Security Choice for 802.11 (WiFi) Radio (If USING Personal WPA/WPA2):

1) Tap: Start > Settings > System > Intermec Settings > Communications >802.11 Radio >

Funk Security

2) Select the Profile 1. (or 2, 3 or 4 if adding additional Profiles)

3) Enter Profile Label (name)

4) Check radio Box for Network type:

a. Infrastructure for Access Points (this is the typical choice)

b Ad Hoc for PC to PC, or Device to Device, or Device to PC

5) Enter SSID (unique wireless network name)

6) Check radio Box for Power Mode: check CAM (for constant awake mode)

7) Select 802.1x security type (if used): none

8) Select Association: WPA or WPA2

9) Set your PSK (aka, Pre-shared key)

The pre-shared key must be a value of 32 hex pairs preceded by 0x

for a total of 66 characters. The value must match the key value on

the access point. The passphrase must be from 8 to 63 characters.

After you enter a passphrase, the 70 Series internally converts it to

a pre-shared key. This value must match the passphrase on the

authenticator.

10) The rest of the screen requires scrolling through to set any necessary security options.

If you don’t know what these are – contact the IT staff.

11) To Save your settings, Select OK at the bottom menu panel if no additional changes are

needed.

Setup Wireless Security Choice for 802.11 (WiFi) Radio (USING Any OTHER Security

Option)……

Reference the supplement document located on the GigaTrak website:

Personal WPA/WPA2): IntermecCK_CN_SC Series WirelessConfigSupplement

Select Active Profile for Wireless Security for 802.11 WiFi) Radio:

1) Tap: Start > Settings > System > Intermec Settings > Communications >802.11 Radio >

Funk Security

2) Select Active Profile

3) Check desired Profile (1, 2, 3 or 4)

4) Enter Profile Label (name)

5) Select OK at the bottom menu panel.

Intermec CS40 Handheld Information

IntermecCS40HandheldInformation080511.doc Page9

Setup IP Configuration for 802.11 (WiFi) Radio network communications:

1) Tap: Start > Settings > System > Intermec Settings > Communications >802.11 Radio >

IP Settingds

2) Select DHCP Check box if DHCP (dynamic host connect protocol) is used and IP address

will automatically be assigned by a server.

3) Enter DHCP client ID (name) if applicable

4) OR

5) Uncheck DHCP if IP is static and will be assigned based on specific IP address given.

6) If Static IP, then enter required additional network information:

a. IP Address

b. Subnet Mask

c. Default Router

d. Primary DNS (if applicable)

e. Secondary DNS (if applicable)

f. Primary WINS (if applicable)

g. Secondary WINS (if applicable)

h. Enter SSID (unique wireless network name)

7) Select OK at the bottom menu panel if no additional changes are needed.

Intermec CS40 Handheld Information

IntermecCS40HandheldInformation080511.doc Page10

APPENDIX 3 – GigaTrak Application Installation Notes

Microsoft Active Sync Installation (For Windows XP)

1) Locate a copy of the latest version of Active Sync for your computer system. The correct version

is available from Microsoft’s WEB site or a copy is included on your CD. Version 4.5 is the latest

from Microsoft as of this printing.

2) Look for the installation file (i.e. activesync_setup.msi) and run it. We recommend that you follow

the installation instructions and accept the standard default settings during your install.

3) Leave Active Sync running to install and connect your handheld computer.

NOTE: Some users may use a single PC to connect multiple handheld computers. If this is the case,

it is best to setup your PC to recognize each handheld as a “Guest”. This avoids having Active Sync

loading shared data from your Outlook and other PC applications. To set all connected handhelds as

a Guest, please double-click and run the provided “GuestOnly.reg” file. It will instantly update your

system for future connections.

Windows Mobile Device Center Installation (For Windows Vista or Windows 7)

1) Locate a copy of the latest version of Windows Mobile Device Center for your computer system.

The correct version is available from Microsoft’s WEB site or a copy is included on your CD.

2) Look for the installation file (i.e. drvupdate-x86.exe) and run it. We recommend that you follow

the installation instructions and accept the standard default settings during your install.

Install GigaTrak Handheld Application – WIRELESS and/or Batch versions

The handheld application files can be found in the PocketPC folder of your installation CD (or was

provided to you via email).

1) Connect the handheld docking station to your computer (typically a USB connection) and plug in

the AC power cable.

2) Put the handheld in the dock and wait for it to sync with the PC.

3) Copy the CAB file to the device using ActiveSync (XP) or Windows Mobile Device Center

(Vista/7). -- Any folder, it doesn't matter where.

4) Once the file(s) is(are) copied, disconnect the USB cable.

5) On the handheld itself, browse to the folder where you installed the *.CAB file and click on the

CAB file to install.

a. WIN_xxx-W.cab (for the Wireless Application

b. WIN_xxx.cab (for the Batch Application)

6) If prompted, select Device as the install location. On the handheld, click the file to run it – this

will install the application on the handheld.

7) Exit out to the main desktop screen on the handheld.

8) Start | Programs | xxx_xxx-W to run the Wireless version of the application

9) Start | Programs | xxx_xxx to run the Batch version of the application

Otros manuales de PDA de gigatrak

gigatrak

gigatrak Intermec CN3 Manual de usuario

Manuales populares de PDA de otras marcas

SPOT

SPOT SPOT Manual de usuario

Palm

Palm handheld Manual de usuario

Winmate

Winmate E500QK Manual de usuario

Getac

Getac PS236 Manual de usuario

Sharp

Sharp CE-1600P Manual de usuario

HTC

HTC PHAR100 Manual de usuario

Mindeo

Mindeo M40 Manual de usuario

Acer

Acer n30 Manual de usuario

ASCOM

ASCOM 9D24 EX Manual de usuario

Unitech

Unitech PA520BTNF Manual de usuario

HandHeld

HandHeld Nautiz X3 Manual de usuario

Casio

Casio PALM Manual de usuario

Sharp

Sharp TM-20 Guía de inicio rápido

Atid

Atid AT870 Manual de usuario

AML

AML M7225 Manual de usuario

Audiovox

Audiovox Maestro Manual técnico

Casio

Casio PV-750 Plus Manual de instrucciones y seguridad

Unitech

Unitech PT630 Manual de usuario

gigatrak Intermec CS40 Manual de usuario

Manuales populares de PDA de otras marcas