Gigabyte GA-8SG667 Manual de usuario

When you installing AGPcard, please make sure the following

notice is fully understood and practiced. If your A G P card has

"AGP 4X/8X(1.5V) notch"(show below), please make sure your AG P

cardis AGP 4X/8X(1.5V).

Caution: A G P 2X card is not supported by SiS ®648. You might

experience system unable to boot up normally. Please insert an

AGP 4X/8X card.

Example 1: Diamond Vipper V770 golden finger is compatible with 2X/4X

mode AGP slot. It can be switched between AGP 2X(3.3V) or 4X(1.5V)

mode by adjusting the jumper. The factory default for this card is

2X(3.3V). The GA-8SG667 (or any AGP 4X only) motherboards might

not function properly, if you install this card without switching the jumper

to 4X(1.5) mode in it.

Example 2: Some ATi Rage 128 Pro graphics cards made by “Power

Color”, the graphics card manufacturer & some SiS 305 cards, their

golden finger is compatible with 2X(3.3V)/4X(1.5V) mode AGP slot, but

they support 2X(3.3V) only. The GA-8SG667 (or any AGP 4X only)

motherboards might not function properly, If you install this card in it.

Note : Although Gigabyte's AG32S(G) graphics card is based on

ATi Rage 128 Pro chip, the design of AG32S(G) is compliance

with AGP 4X(1.5V) specification. Therefore, AG32S (G)will work

fine with SiS®648 based motherboards.

AGP 4X/8X notch

0The author assumes no responsibility for any errors

or omissions that may appear in this document nor

does the author make a commitment to update the

information contained herein.

0Third-party brands and names are the property of

their respective owners.

0Please do not remove any labels on motherboard, this

may void the warranty of this motherboard.

0Due to rapid change in technology, some of the

specifications might be out of date before publication

of this booklet.

Declaration of Conformity

We, Manufacturer/Importer

(full address)

G.B.T. Technology Träding GMbH

Ausschlager Weg 41, 1F, 20537 Hamburg, Germany

declare that the product

( description of the apparatus, system, installation to which it refers)

Mother Board

GA-8SG667

is in conformity with

(reference to the specification under which conformity is declared)

in accordance with 89/336 EEC-EMC Directive



EN 55011 Limits and methods of measurement

of radio disturbance characteristics of

industrial,scientific and medical (ISM

high frequency equipment



EN 61000-3-2*

7EN 60555-2

Disturbances in supply systems cause

by household appliances and similar

electrical equipment “Harmonics”



EN 55013 Limits and methods of measurement

of radio disturbance characteristics of

broadcast receivers and associated

equipment



EN 61000-3-3* Disturbances in supply systems cause

by household appliances and similar

electrical equipment “Voltage fluctuations”



EN 55014 Limits and methods of measurement

of radio disturbance characteristics of

household electrical appliances,

portable tools and similar electrical

apparatus

7EN 50081-1 Generic emission standard Part 1:

Residual commercial and light industry

7EN 50082-1 Generic immunity standard Part 1:

Residual commercial and light industry



EN 55015 Limits and methods of measurement

of radio disturbance characteristics of

fluorescent lamps and luminaries

Generic emission standard Part 2:

Industrial environment



EN 55081-2

Immunity from radio interference of

broadcast receivers and associated

equipment

Generic emission standard Part 2:

Industrial environment



EN 55082-2

7EN 55022 Limits and methods of measurement

of radio disturbance characteristics of

information technology equipment

lmmunity requirements for household

appliances tools and similar apparatus



ENV 55104

Cabled distribution systems; Equipment

for receiving and/or distribution from

sound and television signals

EMC requirements for uninterruptible

power systems (UPS)



EN50091-2



EN 55020



DIN VDE 0855



part 10



part 12

(EC conformity marking)

7CE marking

The manufacturer also declares the conformity of above mentioned product

with the actual required safety standards in accordance with LVD 73/23 EEC

Safety requirements for mains operated

electronic and related apparatus for

household and similar general use



EN 60950



EN 60065

Safety of household and similar

electrical appliances



EN 60335

Manufacturer/Importer

Signature:

Name:

(Stamp) Date : August 26, 2002

7EN 60555-3

Timmy Huang



EN 50091-1

FCC Part 15, Subpart B, Section 15.107(a) and Section 15.109

(a),Class B Digital Device

DECLARATION OF CONFORMITY

Per FCC Part 2 Section 2.1077(a)

Responsible Party Name:

Address:

Phone/Fax No:

hereby declares that the product

Product Name:

Conforms to the following specifications:

This device complies with part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) This device may not

cause harmful and (2) this device must accept any inference received,

including that may cause undesired operation.

Representative Person’s Name:

Signature: Eric Lu

Supplementary Information:

Model Number:

17358 Railroad Street

City of Industry, CA 91748

G.B.T. INC. (U.S.A.)

(818) 854-9338/ (818) 854-9339

Motherboard

GA-8SG667

Date:

ERIC LU

August 26, 2002

USER’S MANUAL

GA-8SG667

P4 Titan DDR Motherboard

Pentium®4 Processor Motherboard

Rev. 1001

12ME-8SG667-1001

- 2 -GA-8SG667 Motherboard

English

Table of Content

Item Checklist ......................................................................................... 4

WARNING! ............................................................................................... 4

Chapter 1 Introduction ............................................................................. 5

Features Summary ...................................................................................... 5

GA-8SG667 Motherboard Layout ............................................................... 7

Chapter 2 Hardware Installation Process ................................................ 8

Step 1: Install the Central Processing Unit (CPU)....................................... 9

Step1-1 : CPU Installation ................................................................................................. 9

Step1-2 : CPU Heat Sink Installation ............................................................................. 10

Step 2: Install memory modules ................................................................ 11

Step 3: Install expansion cards ................................................................. 12

Step 4: Connect ribbon cables, cabinet wires, and power supply ........... 13

Step4-1:I/O Back Panel Introduction .............................................................................. 13

Step 4-2 : Connectors Introduction ................................................................................. 15

Chapter 3 BIOS Setup .......................................................................... 23

The Main Menu (For example: BIOS Ver. : E12) ...................................... 24

Standard CMOS Features......................................................................... 26

Advanced BIOS Features .......................................................................... 29

Integrated Peripherals .............................................................................. 31

Power Management Setup ....................................................................... 35

Table of Content

English

- 3 -

PnP/PCI Configurations ............................................................................. 37

PC Health Status........................................................................................ 38

Frequency/Voltage Control ........................................................................ 39

Top Performance ...................................................................................... 41

Load Fail-Safe Defaults ............................................................................. 42

Load Optimized Defaults ........................................................................... 43

Set Supervisor/User Password .................................................................. 44

Save & Exit Setup ....................................................................................... 45

Exit Without Saving ................................................................................... 46

Chapter 4 Technical Reference ............................................................ 49

Block Diagram ........................................................................................... 49

@ BIOSTM Introduction............................................................................... 50

Easy TuneTM 4 Introduction ....................................................................... 51

BIOS Flash Introduction ............................................................................ 52

2-/4-/6-Channel Audio Function Introuction .............................................. 67

Chapter 5 Appendix .............................................................................. 75

- 4 -GA-8SG667 Motherboard

English

The GA-8SG667 motherboard 2 Port USB Cable x 1

IDE cable x 2/ Floppy cable x 1 4 Port USB Cable x 1

CD for motherboard driver & utility (TUCD) SPDIF-KIT x 1 (SPD-KIT)

GA-8SG667 user’s manual IEEE 1394 Cable x1

I/O Shield Center/Subwoofer Cable x1 (SURROUND-KIT)

Quick PC Installation Guide Motherboard Settings Label

RAID Manual

Item Checklist

Computer motherboards and expansion cards contain very delicate Integrated Circuit (IC) chips. To

protect them against damage from static electricity, you should follow some precautions whenever you

work on your computer.

1. Unplug your computer when working on the inside.

2. Use a grounded wrist strap before handling computer components. If you do not have

one, touch both of your hands to a safely grounded object or to a metal object, such as

the power supply case.

3. Hold components by the edges and try not touch the IC chips, leads or connectors, or

othercomponents.

4. Place components on a grounded antistatic pad or on the bag that came with the

components whenever the components are separated from the system.

5. Ensure that the ATX power supply is switched off before you plug in or remove the ATX

power connector on the motherboard.

If the motherboard has mounting holes, but they don’t line up with the holes on the base and there are

no slots to attach the spacers, do not become alarmed you can still attach the spacers to the mounting

holes. Just cut the bottom portion of the spacers (the spacer may be a little hard to cut off, so be careful

of your hands). In this way you can still attach the motherboard to the base without worrying about short

circuits. Sometimes you may need to use the plastic springs to isolate the screw from the motherboard

PCB surface, because the circuit wire may be near by the hole. Be careful, don’t let the screw contact

any printed circuit write or parts on the PCB that are near the fixing hole, otherwise it may damage the

board or cause board malfunctioning.

Installing the motherboard to the chassis…

WARNING!

Introduction

English

- 5 -

Chapter 1 Introduction

to be continued......

Features Summary

Form Factor y29.5cm x 20cm ATX size form factor, 4 layers PCB.

CPU ySocket 478 for Intel®Micro FC-PGA2 Pentium®4 processor

y Support Intel ®Pentium ®4 (Northwood, 0.13 m) processor

yIntel Pentium®4 400/533MHz FSB

y2nd cache depends on CPU

Chipset ySiS 648 Host/Memory controller

ySiS 963 MuTIOL Media I/O

Memory y3 184-pin DDR DIMM sockets

ySupports DDR400<Note 1>/DDR333/DDR266/DDR200 DIMM

ySupports Up to 2 un-buffer DIMM DDR333 or up to 3 un-buffer

Double-sided DIMM DDR266/200

ySupports up to 3GB DRAM (Max)

ySupports only 2.5V DDR DIMM

I/O Control yIT8700

Slots y1 AGP slot 4X/8X (1.5V) device support

y5 PCI slot supports 33MHz & PCI 2.2 compliant

On-Board IDE y2 IDE bus master (UDMA33/ATA66/ATA100/ATA133) IDE ports

for up to 4 ATAPI devices

ySupports PIO mode3,4 (UDMA 33/ATA66/ATA100/ATA133) IDE

& ATAPICD-ROM

On-Board Peripherals y1 Floppy port supports 2 FDD with 360K, 720K,1.2M, 1.44M

and 2.88M bytes.

y1 Parallel port supports Normal/EPP/ECP mode

y2 Serial ports (COMA&COMB)

y6 USB 2.0/1.1 ports (2 x Rear, 4 xFront by cable)

y1 Front Audio Connector

Hardware Monitor yCPU/System Fan Revolution detect

yCPU/System Fan Fail Warning

<Note 1> DDR400 only support by SAMSUNG, ADATA, Winbond DDR module as we verified, more

detail pls refer to P82.

- 6 -GA-8SG667 Motherboard

English

Please set the CPU host frequency in accordance with your processor’s specifications.

We don’t recommend you to set the system bus frequency over the CPU’s specification

because these specific bus frequencies are not the standard specifications for CPU,

chipset and most of the peripherals. Whether your system can run under these specific

bus frequencies properly will depend on your hardware configurations, including CPU,

Chipsets,SDRAM,Cards….etc.

On-Board Sound yRealtek ALC650 CODEC

yLine Out / 2 front speaker

yLine In / 2 rear speaker(by s/w switch)

yMic In / center& subwoofer(by s/w switch)

ySPDIF out

yCD In/ AUX_IN/ Game Port

PS/2 Connector yPS/2 Keyboard interface and PS/2 Mouse interface

BIOS yLicensed AWARD BIOS, 2M bit Flash ROM

ySupports Q-Flash

AdditionalFeatures yPS/2 Keyboard power on by password

yPS/2 Mouse power on

ySTR(Suspend-To-RAM)

yAC Recovery

yUSB KB/Mouse wake up from S3

ySupports EasyTune 4

ySupports @BIOS

Tabla de contenidos

Otros manuales de Placa madre de Gigabyte

Gigabyte

Gigabyte GA-8I945GMF Manual de usuario

Gigabyte

Gigabyte GA-965P-DQ6 Manual de usuario

Gigabyte

Gigabyte GA-B85-D3V-A Manual de usuario

Gigabyte

Gigabyte X670E AORUS PRO X Manual de usuario

Gigabyte

Gigabyte Z790 EAGLE AX Manual de usuario

Gigabyte

Gigabyte GA-880GM-D2H Manual de usuario

Gigabyte

Gigabyte GA-8I915MD-GV Manual de usuario

Gigabyte

Gigabyte 6CX7 Series Manual de usuario

Gigabyte

Gigabyte GA-Z270MX-Gaming 5 Manual de usuario

Gigabyte

Gigabyte GA-7BESH Manual de usuario

Gigabyte

Gigabyte R152-Z31 Manual de usuario

Gigabyte

Gigabyte GA-M61PME-S2 Manual de usuario

Gigabyte

Gigabyte GA-4MXSV Manual de usuario

Gigabyte

Gigabyte GA-AX370-Gaming 5 Manual de usuario

Gigabyte

Gigabyte GA-870A-UD3 Manual de usuario

Gigabyte

Gigabyte GA-880GMA-USB3 Manual de usuario

Gigabyte

Gigabyte GA-M68MT-S2P Manual de usuario

Gigabyte

Gigabyte B460 AORUS PRO AC Manual de usuario

Gigabyte

Gigabyte GA-770T-USB3 Manual de usuario

Gigabyte

Gigabyte GA-P55A-UD7 Manual de usuario

Gigabyte

Gigabyte GA-B150M-HD3 DDR3 Manual de usuario

Gigabyte

Gigabyte GA-Z68X-UD7-B3 Manual de usuario

Gigabyte

Gigabyte GA-K8NMF-9 Manual de usuario

Gigabyte

Gigabyte GA-990FX Manual de usuario

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manual de usuario