Gigabyte GA-8IR533 Manual de usuario

When you installing A G P card, please make sure the following

notice is fully understood and practiced. If your AGP card has

"AGP 4X notch"(show below), please make sure your AGP cardis

AGP 4X (1.5V).

Do not use AGP 2Xcard (3.3V) in this motherboard. It will

burn and damage the motherboard due to Intel ®845(E/G) / 850(E)

chipset can't support AGP 2X(3.3V).

Example 1: Diamond Vipper V770 golden finger is compatible with 2X/

4X mode AGP slot. It can be switched between AGP 2X(3.3V) or

4X (1.5V) mode by adjusting the jumper. The factory default for this card

is 2X (3.3V). If you install this card in GA-8IR533 Series (or any AGP 4X

only) motherboards without switching the jumper to 4X mode (1.5V), it

will burn the motherboard.

Example 2: Some ATi Rage 128 Pro graphics cards made by “Power

Color”, the graphics card manufacturer & some SiS 305 cards, their

golden finger is compatible with 2X/4X mode AGP slot, but they support

2X(3.3V) only. If you install this card in GA-8IR533 Series (or any AGP

4X only) motherboards, it will burn the motherboard.

Note : Although Gigabyte's AG32S(G) graphics card is based on ATi Rage

128 Pro chip, the design of AG32S(G) is compliance with AGP 4X (1.5V)

specification. Therefore, AG32S(G) will work fine with Intel®845(E/G) /

850(E) based motherboards.

0The author assumes no responsibility for any errors

or omissions that may appear in this document nor

does the author make a commitment to update the

information contained herein.

0Third-party brands and names are the property of

their respective owners.

0Please do not remove any labels on motherboard, this

may void the warranty of this motherboard.

0Due to rapid change in technology, some of the

specifications might be out of date before publication

of this booklet.

Declaration of Conformity

We, Manufacturer/Importer

(full address)

G.B.T. Technology Träding GMbH

Ausschlager Weg 41, 1F, 20537 Hamburg, Germany

declare that the product

( description of the apparatus, system, installation to which it refers)

Mother Board

GA-8IR533

is in conformity with

(reference to the specification under which conformity is declared)

in accordance with 89/336 EEC-EMC Directive



EN 55011 Limits and methods of measurement

of radio disturbance characteristics of

industrial,scientific and medical (ISM

high frequency equipment



EN 61000-3-2*

7EN 60555-2

Disturbances in supply systems cause

by household appliances and similar

electrical equipment “Harmonics”



EN 55013 Limits and methods of measurement

of radio disturbance characteristics of

broadcast receivers and associated

equipment



EN 61000-3-3* Disturbances in supply systems cause

by household appliances and similar

electrical equipment “Voltage fluctuations”



EN 55014 Limits and methods of measurement

of radio disturbance characteristics of

household electrical appliances,

portable tools and similar electrical

apparatus

7EN 50081-1 Generic emission standard Part 1:

Residual commercial and light industry

7EN 50082-1 Generic immunity standard Part 1:

Residual commercial and light industry



EN 55015 Limits and methods of measurement

of radio disturbance characteristics of

fluorescent lamps and luminaries

Generic emission standard Part 2:

Industrial environment



EN 55081-2

Immunity from radio interference of

broadcast receivers and associated

equipment

Generic emission standard Part 2:

Industrial environment



EN 55082-2

7EN 55022 Limits and methods of measurement

of radio disturbance characteristics of

information technology equipment

lmmunity requirements for household

appliances tools and similar apparatus



ENV 55104

Cabled distribution systems; Equipment

for receiving and/or distribution from

sound and television signals

EMC requirements for uninterruptible

power systems (UPS)



EN50091-2



EN 55020



DIN VDE 0855



part 10



part 12

(EC conformity marking)

7CE marking

The manufacturer also declares the conformity of above mentioned product

with the actual required safety standards in accordance with LVD 73/23 EEC

Safety requirements for mains operated

electronic and related apparatus for

household and similar general use



EN 60950



EN 60065

Safety of household and similar

electrical appliances



EN 60335

Manufacturer/Importer

Signature:

Name:

(Stamp) Date : May. 17, 2002

7EN 60555-3

Timmy Huang



EN 50091-1

FCC Part 15, Subpart B, Section 15.107(a) and Section 15.109

(a),Class B Digital Device

DECLARATION OF CONFORMITY

Per FCC Part 2 Section 2.1077(a)

Responsible Party Name:

Address:

Phone/Fax No:

hereby declares that the product

Product Name:

Conforms to the following specifications:

This device complies with part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) This device may not

cause harmful and (2) this device must accept any inference received,

including that may cause undesired operation.

Representative Person’s Name:

Signature: Eric Lu

Supplementary Information:

Model Number:

17358 Railroad Street

City of Industry, CA 91748

G.B.T. INC. (U.S.A.)

(818) 854-9338/ (818) 854-9339

Motherboard

GA-8IR533

Date:

ERIC LU

May 17, 2002

USER’S MANUAL

GA-8IR533 Series

P4 Titan DDR Motherboard

Pentium®4 Processor Motherboard

Rev. 1003

12ME-8IR533-1003

GA-8IR533 Series Motherboard

Table of Content

Item Checklist ......................................................................................... 4

WARNING! ............................................................................................... 4

Chapter 1 Introduction ............................................................................. 5

Features Summary ...................................................................................... 5

GA-8IR533 Series Motherboard Layout ...................................................... 7

Chapter 2 Hardware Installation Process ................................................ 8

Step 1: Install the Central Processing Unit (CPU)....................................... 9

CPU Installation ................................................................................................................. 9

CPU Heat Sink Installation .............................................................................................. 10

Step 2: Install memory modules ................................................................ 11

Step 3: Install expansion cards ................................................................. 13

Step 4: Connect ribbon cables, cabinet wires, and powersupply ............ 14

Step4-1: I/O Back Panel Introduction ............................................................................. 14

Step4-2: Connectors Introduction ................................................................................... 16

Step4-3: Jumper Introduction .......................................................................................... 22

Chapter 3BIOS Setup ........................................................................... 23

The Main Menu (For example: BIOS Ver. :F1) ......................................... 24

Standard CMOS Features......................................................................... 26

Advanced BIOS Features .......................................................................... 29

Integrated Peripherals .............................................................................. 31

Power Management Setup ....................................................................... 36

PnP/PCI Configurations ............................................................................. 39

Table of Content

Q-Flash Introduction.................................................................................. 50

@ BIOSTM Introduction............................................................................... 52

Easy TuneTM 4 Introduction ....................................................................... 53

Chapter 5 Appendix .............................................................................. 54

PC Health Status........................................................................................ 40

Frequency/Voltage Control ........................................................................ 41

Top Performance ...................................................................................... 43

Load Fail-Safe Defaults ............................................................................. 44

Load Optimized Defaults ........................................................................... 45

Set Supervisor/User Password .................................................................. 46

Save & Exit Setup ....................................................................................... 47

Exit Without Saving ................................................................................... 48

Chapter 4 Technical Reference ............................................................ 49

Block Diagram ........................................................................................... 49

GA-8IR533 Series Motherboard

Computer motherboards and expansion cards contain very delicate Integrated Circuit (IC) chips. To

protect them against damage from static electricity, you should follow some precautions whenever you

work on your computer.

1. Unplug your computer when working on the inside.

2. Use a grounded wrist strap before handling computer components. If you do not have

one, touch both of your hands to a safely grounded object or to a metal object, such as

the power supply case.

3. Hold components by the edges and try not touch the IC chips, leads or connectors, or

othercomponents.

4. Place components on a grounded antistatic pad or on the bag that came with the

components whenever the components are separated from the system.

5. Ensure that the ATX power supply is switched off before you plug in or remove the ATX

power connector on the motherboard.

If the motherboard has mounting holes, but they don’t line up with the holes on the base and there are

no slots to attach the spacers, do not become alarmed you can still attach the spacers to the mounting

holes. Just cut the bottom portion of the spacers (the spacer may be a little hard to cut off, so be careful

of your hands). In this way you can still attach the motherboard to the base without worrying about short

circuits. Sometimes you may need to use the plastic springs to isolate the screw from the motherboard

PCB surface, because the circuit wire may be near by the hole. Be careful, don’t let the screw contact

any printed circuit write or parts on the PCB that are near the fixing hole, otherwise it may damage the

board or cause board malfunctioning.

Installing the motherboard to the chassis…

WARNING!

The GA-8IR533 Series motherboard GA-8IR533 Series user’s manual

IDE cable x 1/ Floppy cable x 1 Quick PC Installation Guide

CD for motherboard driver & utility

Item Checklist

Introduction

Form Factor 19.6cm x 29.5cm ATX size form factor, 4 layers PCB.

Motherboard GA-8IR533 Series include:

 GA-8IR & GA-8IR533

CPU Socket 478 for Intel®Micro FC-PGA2 Pentium®4 processor

 Support Intel®Pentium®4 (Northwood, 0.13

m) processor

Intel Pentium®4 400MHz FSB

Auto detect and optimized setting for Pentium ®4 FSB 533MHZ

processor (8IR533 only)

2nd cache depends on CPU

Chipset Chipset Intel 845D HOST/AGP/Controller

ICH2 I/O Controller Hub

Memory 3 184-pin DDR DIMM sockets

Supports PC2100 DDR or PC1600 DDR DIMM

Supports up to 2GB DRAM (Max)

Supports only 2.5V DDR DIMM

Supports 64bit ECC type DRAM integrity mode

I/O Control ITE8702

Slots 1 AGP slot 4X (1.5V) device support

5 PCI slot supports 33MHz & PCI 2.2 compliant

On-Board IDE 2 IDE bus master (DMA33/ATA66/ATA100) IDE ports for up to 4

ATAPI devices

Supports PIO mode3,4 (UDMA 33/ATA66/ATA100) IDE & ATAPI

CD-ROM

On-Board Peripherals 1 Floppy port supports 2 FDD with 360K, 720K,1.2M, 1.44M

and 2.88M bytes.

1 Parallel port supports Normal/EPP/ECP mode

2 Serial ports (COMA & COMB)

4 x USB 1.1 (2 by cable )

1 Front Audio connector

Chapter 1 Introduction

to be continued......

Features Summary

GA-8IR533 Series Motherboard

On-Board Sound Realtek ALC650 CODEC

Line Out / 2 front speaker

Line In / 2 rear speaker(by s/w switch)

Mic In / center & woofer(by s/w switch)

SPDIF out : by s/w switch

CD In / AUX In / Game port

PS/2 Connector PS/2 Keyboard interface and PS/2 Mouse interface

BIOS Licensed AWARD BIOS, 2M bit FWH

Supports Q-Flash

AdditionalFeatures PS/2 Keyboard password power on

PS/2 Mouse power on

STR(Suspend-To-RAM)

AC Recovery

USB KB/Mouse wake up from S3

Poly fuse for keyboard,USB,game port over-current protection

Supports @BIOS

Supports EasyTune 4

Jumper less Over Clock (CPU/DDR/AGP) by BIOS

Overclocking

Please set the CPU host frequency in accordance with your processor’s specifications.

We don’t recommend you to set the system bus frequency over the CPU’s specification

because these specific bus frequencies are not the standard specifications for CPU,

chipset and most of the peripherals. Whether your system can run under these specific

bus frequencies properly will depend on your hardware configurations, including CPU,

Chipsets,SDRAM,Cards….etc.

Otros manuales para GA-8IR533

Tabla de contenidos

Otros manuales de Placa madre de Gigabyte

Gigabyte

Gigabyte GA-586MS Manual de usuario

Gigabyte

Gigabyte Z390 AORUS XTREME Manual de usuario

Gigabyte

Gigabyte GA-A55M-DS2 Manual de usuario

Gigabyte

Gigabyte GA-Z77X-UP7 Manual de usuario

Gigabyte

Gigabyte GA-E2100N Manual de usuario

Gigabyte

Gigabyte GA-MA790GP-DS4H Manual de usuario

Gigabyte

Gigabyte GA-F2A88XM-DS2P Manual de usuario

Gigabyte

Gigabyte Z590 AORUS PRO AX Manual de usuario

Gigabyte

Gigabyte MZ73-LM0 Manual de usuario

Gigabyte

Gigabyte R280-F2O Manual de usuario

Gigabyte

Gigabyte GA-Z97M-D3HP Manual de usuario

Gigabyte

Gigabyte GA-990FXA-UD5 Manual de usuario

Gigabyte

Gigabyte GA-7PESH3 Manual de usuario

Gigabyte

Gigabyte GA-P61A-D3 Manual de usuario

Gigabyte

Gigabyte GA-M52LT-D3P Manual de usuario

Gigabyte

Gigabyte GA-945PL-S3E Manual de usuario

Gigabyte

Gigabyte GA-880GA-UD3H Manual de usuario

Gigabyte

Gigabyte GA-MA770T-ES3 Manual de usuario

Gigabyte

Gigabyte B650M GAMING X AX Manual de usuario

Gigabyte

Gigabyte GA-K8VT800-RH Manual de usuario

Gigabyte

Gigabyte 5AA Manual de usuario

Gigabyte

Gigabyte GA-7DXR Manual de usuario

Gigabyte

Gigabyte GA-H61M-S2P-B3 Manual de usuario

Gigabyte

Gigabyte GA-MA770T-UD3P Manual de usuario

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manual de usuario