Gigabyte GA-8IE2004P Manual de usuario

Whenyou installing AGPcard,please make surethefollow

ing notice isfullyunderstood and practiced.IfyourAGP

cardhas "AGP4Xnotch"(showbelow),please make sure

yourAGPcardisAGP4X(1.5V).

Caution:AGP2X(3.3V)cardisnotsupportedbyIntel®845

(E/G)/Intel®850(E).You mightexperience systemunableto

bootup normally.Please insertanAGP4X(1.5V)card

Example1:Diamond VipperV770 golden fingeriscompatible

with2X/4Xmode AGPslot. It can be switched between AGP2X

(3.3V)or4X(1.5V)mode byadjusting the jumper.The factory

defaultforthiscardis2X(3.3V).The GA-8IE2004P(-L)(orany

AGP4Xonly)motherboardsmightnotfunction properly,ifyou install

thiscardwithoutswitching the jumperto4X(1.5)mode init.

Example2:SomeATiRage 128 Prographics cardsmade by

"PowerColor",the graphics cardmanufacturer&someSiS305

cards,theirgolden fingeriscompatiblewith2X/4Xmode AGP

slot, buttheysupport2X(3.3V)only.The GA-8IE2004P(-L)(orany

AGP4Xonly)motherboardsmightnotfunction properly,If you install

this cardinit.

Note:Although Gigabyte'sAG32S(G)graphics cardisbased on

ATiRage 128 Prochip,the design ofAG32S(G)iscompliance

withAGP4X(1.5V)specification.Therefore,AG32S(G)will work

fine withIntel®845(E/G)/850(E)based motherboards.

MTheauthorassumes no responsibilityforanyerrorsoromissions

thatmay appearinthisdocumentnordoes theauthormake a

commitmenttoupdatetheinformation containedherein.

MThird-partybrandsand names arethepropertyoftheirrespective

owners.

MPlease do notremove anylabelson motherboard,thismay voidthe

warrantyofthismotherboard.

MDuetorapidchangeintechnology,someofthespecificationsmight

beoutofdatebeforepublication ofthisbooklet.

Declaration ofConformity

We,Manufacturer/Importer

(full address)

G.B.T.TechnologyTräding GMbH

AusschlagerWeg41,1F,20537 Hamburg,Germany

declarethatthe product

(description ofthe apparatus,sy stem,installation towhichitrefers)

MotherBoard

GA-8IE2004P

isinconformitywith

(referencetothe specification underwhichconformityisdeclared)

inaccordancewith89/336 EEC-EMCDirective

oEN55011 Limitsand methodsofmeasurement

ofradiodisturbancecharacteristics of

industrial,scientificand medical(ISM

high frequency equipment

oEN61000-3-2*

TEN60555-2

Disturbancesinsupplysystemscause

byhouseholdappliancesand similar

electricalequipment“Harmonics”

oEN55013 Limitsand methodsofmeasurement

ofradiodisturbancecharacteristics of

broadcastreceiversand associated

equipment

oEN61000-3-3*Disturbancesinsupplysystemscause

byhouseholdappliancesand similar

electricalequipment“Voltage fluctuations”

oEN55014 Limitsand methodsofmeasurement

ofradiodisturbancecharacteristics of

householdelectricalappliances,

portabletoolsand similarelectrical

apparatus

TEN50081-1Genericemission standardPart1:

Residualcommercialand lightindustry

TEN50082-1GenericimmunitystandardPart1:

Residualcommercialand lightindustry

oEN55015 Limitsand methodsofmeasurement

ofradiodisturbancecharacteristics of

fluorescentlampsand luminaries

Genericemission standardPart2:

Industrialenvironment

oEN55081-2

Immunityfromradiointerferenceof

broadcastreceiversand associated

equipment

Genericemission standardPart2:

Industrialenvironment

oEN55082-2

TEN55022 Limitsand methodsofmeasurement

ofradiodisturbancecharacteristics of

information technologyequipment

lmmunityrequirementsforhousehold

appliancestoolsand similarapparatus

oENV55104

Cabled distribution systems;Equipment

forreceiving and/ordistribution from

sound and television signals

EMCrequirementsforuninterruptible

powersystems(UPS)

oEN50091-2

oEN55020

oDINVDE0855

opart10

opart12

(ECconformitymarking)

TCEmarking

Themanufactureralsodeclares theconformityofabove mentionedproduct

withtheactualrequiredsafetystandardsinaccordance withLVD73/23 EEC

Safetyrequirementsformainsoperated

electronicand related apparatusfor

householdand similargeneraluse

oEN60950

oEN60065

Safetyofhouseholdand similar

electricalappliances

oEN60335

Manufacturer/Importer

Signature:

Name:

Date:July9,2003

TEN60555-3

TimmyHuang

oEN50091-1

TimmyHuang

Safetyforinformation technologyequipment

including electricalbussiness equipment

Generaland Safetyrequirmentsfor

uninterruptiblepowersystems(UPS)

FCC Part15,SubpartB,Section 15.107(a)and Section 15.109

(a),Class BDigitalDevice

DECLARATIONOFCONFORMITY

PerFCC Part2Section 2.1077(a)

ResponsiblePartName:

Address:

Phone/FaxNo:

hereby declaresthattheproduct

ProductName:

Conformstothefollowing specifications:

Thisdevice complieswithpart15 oftheFCC Rules.Operation is

subjecttothefollowing twoconditions:(1)Thisdevice maynot

causeharmfuland (2)thisdevicemustacceptanyinference received,

including thatmaycauseundesiredoperation.

RepresentativePerson’sName:

Signature:EricLu

SupplementaryInformation:

ModelNumber:

17358RailroadStreet

CityofIndustry,CA 91748

G.B.T.INC.(U.S.A.)

(818)854-9338/(818)854-9339

Motherboard

GA-8IE2004P

Date:

ERICLU

July9,2003

USER'S MANUAL

GA-8IE2004P(-L)

P4 Titan Motherboard

Pentium®4 Processor Motherboard

Rev.1001

12ME-8IE04P-1001

- 2 -GA-8IE2004P(-L) Motherboard

English

Table of Content

Item Checklist.........................................................................................4

WARNING! ..............................................................................................4

Chapter 1 Introduction.............................................................................5

Features Summary....................................................................................... 5

GA-8IE2004P(-L) Motherboard Layout ........................................................ 7

Chapter 2 Hardware Installation Process................................................8

Step 1: Install the Central Processing Unit (CPU)........................................ 9

Step 1-1 CPU Installation .................................................................................. 9

Step 1-2 : CPU Heat Sink Installation.............................................................. 10

Step 2: Install memory modules................................................................. 11

Step 3: Install expansion cards .................................................................. 12

Step 4: Connect ribbon cables, cabinet wires, and power supply.............. 13

Step 4-1 : I/O Back Panel Introduction ............................................................ 13

Step 4-2 :Connectors & Jumper Setting Introduction....................................... 15

Chapter 3 BIOS Setup ..........................................................................27

The Main Menu (For example: BIOS Ver. :E3)........................................... 28

Standard CMOS Features.......................................................................... 30

Advanced BIOS Features........................................................................... 33

Integrated Peripherals............................................................................... 35

Table of Content

English

- 3 -

Power Management Setup......................................................................... 39

PnP/PCI Configurations ............................................................................. 42

PC Health Status........................................................................................ 43

Frequency/Voltage Control......................................................................... 45

Top Performance ........................................................................................ 47

Load Fail-Safe Defaults.............................................................................. 48

Load Optimized Defaults ............................................................................ 49

Set Supervisor/User Password .................................................................. 50

Save & Exit Setup ...................................................................................... 51

Exit Without Saving ................................................................................... 52

Chapter 4 Technical Reference .............................................................55

Block Diagram ............................................................................................ 55

@ BIOS Introduction .................................................................................. 56

Easy Tune 4TM Introduction......................................................................... 57

BIOS Flash PRocedure .............................................................................. 58

2-/4-/6-ChannelAudio Function Introduction.............................................. 62

Jack-Sensing Introuction........................................................................... 68

Chapter 5Appendix...............................................................................71

- 4 -GA-8IE2004P(-L) Motherboard

English

þGA-8IE2004P(-L)motherboard þ2 Port USB Cable x 1

þIDE cable x 2/ Floppy cable x 1 o4 Port USB Cable x 1

þCD for motherboard driver & utility (IUCD) oSPDIF KIT x 1(SPD-KIT)

þGA-8IE2004P(-L)user's manual oIEEE 1394 Cable x1

þI/O Shield * oCenter/SubwooferCable x1

þQuick PC Installation Guide (SURROUND-KIT)

oRAIDManual þMotherboard Settings Label

Item Checklist

Computermotherboards and expansion cardscontainvery delicate Integrated Circuit(IC)chips. To

protect them against damage from static electricity, you should follow some precautions whenever

you work on your computer.

1. Unplug your computer when working on the inside.

2. Use a grounded wrist strap before handling computer components. If you do not have

one, touch both of your hands to a safely grounded object or to a metal object, such as

the power supply case.

3. Hold components by the edges and try not touch the IC chips, leads or connectors, or

other components.

4. Place components on a grounded antistatic pad or on the bag that came with the

components whenever the components are separated from the system.

5. Ensure that theATX power supply is switched off before you plug in or remove theATX

ower connector on the motherboard.

If the motherboard has mounting holes, but they don’t line up with the holes on the base and

thereare no slotsto attach the spacers, do not becomealarmed you canstill attach the spacersto

the mounting holes. Just cut the bottom portion of the spacers (the spacer may be a little hard to

cut off, so be careful of your hands). In this way you can still attach the motherboard to the base

withoutworryingabout short circuits. Sometimes youmayneedto use the plastic springstoisolate

thescrewfromthemotherboardPCBsurface,becausethecircuitwiremaybenearbythehole.Be

careful, don’t let the screw contact any printed circuit write or parts on the PCB that are near the

fixing hole, otherwise it may damage the board or cause board malfunctioning.

Installing the motherboard to the chassis…

WARNING!

* For GA-8IE2004P-L only

Introduction- 5 -

English

Form Factor 29.3cm x 20.0cmATX size form factor, 4 layers PCB.

CPU Socket 478 for Intel®Micro FC-PGA2 Pentium®4 processor

Intel Pentium®4 533MHz/400MHz FSB

Support Intel ®Pentium®4 (Northwood, 0.13 m) processor

 Support Intel®Pentium ®4 Processor with HT Technology

2nd cache depend on CPU

Chipset Chipset 845E HOST/AGP/Controller

ICH4 I/O Controller Hub

Memory 3 184-pin DDR DIMM sockets

Supports PC2100 DDR or PC1600 DDR DIMM

Supports up to 2GB DRAM (Max)

Supports only 2.5V DDR DIMM

I/OControl IT8712

Slots 1AGP slot 4X (1.5V only) device support

5 PCI slot supports 33MHz & PCI 2.2 compliant

On-Board IDE 2 IDE controllers on the Intel ICH4 PCI chipset

providesIDEHDD/CD-ROM (IDE1, IDE2) with PIO,BusMaster

(Ultra DMA33/ATA66/ATA100) operation modes.

On-Board Peripherals 1 Floppy port supports 2 FDD with 360K, 720K,1.2M, 1.44M

and 2.88M bytes.

1 Parallel port supports Normal/EPP/ECP mode

2 Serial ports (COMA & COMB)

6 x USB 2.0/1.1 (2 x Rear,4 xFront by cable )

1 Front Audio connector

On-BoardSound RealtekALC655 CODEC

Supports Jack Sensing function

Line Out / 2 front speaker

Line In / 2 rear speaker(by s/w switch)

Mic In / center& subwoofer(by s/w switch)

SPDIF out /SPDIF In

CD In / AUX In / Game port

Chapter 1 Introduction

to be continued......

Features Summary

- 6 -GA-8IE2004P(-L) Motherboard

English

On-Board USB 2.0 Built in ICH4 Chipset

On-Board LAN* Builit in Realtek 8100C

1 RJ45 port

PS/2Connector PS/2 Keyboard interface and PS/2 Mouse interace

BIOS LicensedAWARD BIOS

Supports Q-Flash

HardwareMonitor CPU/System Fan Revolution detect

CPU/System Fan Fail Warning

CPUOverheat Warning

System Voltage Detect

AdditionalFeatures PS/2 Keyboard power on by password

PS/2 Mouse power on

External Modem wake up

STR(Suspend-To-RAM)

ACRecovery

Poly fuse for keyboard over-current protection

USB KB/Mouse wake up from S3

Supports@BIOS

Supports EasyTune 4

Overclocking Over Clock (CPU/DDR/AGP/PCI) by BIOS

Over Voltage (CPU/DDR/AGP) by BIOS

HT functionality requirement content :

EnablingthefunctionalityofHyper-ThreadingTechnologyforyour computer system requires all

ofthefollowingplatform components:

- CPU:An Intel®Pentium4 Processor with HTTechnology

-Chipset:AnIntel®ChipsetthatsupportsHTTechnology

-BIOS:ABIOS that supports HTTechnology and has it enabled

-OS:AnoperationsystemthathasoptimizationsforHTTechnology

Please set the CPU host frequency in accordance with your processor’s specifications.

We don’t recommend you to set the system bus frequency over the CPU’s specification

because these specific bus frequencies are not the standard specifications for CPU,

chipset and most of the peripherals. Whether your system can run under these specific

bus frequencies properly will depend on your hardware configurations, including CPU,

Chipsets,SDRAM,Cards….etc.

* For GA-8IE2004P-L only

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Placa madre de Gigabyte

Gigabyte

Gigabyte G1.Sniper Z170 Manual de usuario

Gigabyte

Gigabyte GA-8AENXP-D Manual de usuario

Gigabyte

Gigabyte GA-8I945P-G-RH Manual de usuario

Gigabyte

Gigabyte GA-X79-UD7 Manual de usuario

Gigabyte

Gigabyte GA-Z77-HD3 Manual de usuario

Gigabyte

Gigabyte GA-X99-Gaming 7WIFI Manual de usuario

Gigabyte

Gigabyte GS-R22PE Manual de usuario

Gigabyte

Gigabyte Z690 AORUS XTREME WB Manual de usuario

Gigabyte

Gigabyte GA-8I865PE775-G-RH Manual de usuario

Gigabyte

Gigabyte GA - 586ATX Manual de usuario

Gigabyte

Gigabyte Z690 UD AC Manual de usuario

Gigabyte

Gigabyte GA-8I865GMFK-775 Manual de usuario

Gigabyte

Gigabyte GA-PH67A-D3-B3 Manual de usuario

Gigabyte

Gigabyte GA-8I875 Manual de usuario

Gigabyte

Gigabyte GA-6CXC Manual de usuario

Gigabyte

Gigabyte GA-M57SLI-S4 Manual de usuario

Gigabyte

Gigabyte GA-P75-D3 Manual de usuario

Gigabyte

Gigabyte 8S651MP-RZ Manual de usuario

Gigabyte

Gigabyte GA-B85-HD3-A Manual de usuario

Gigabyte

Gigabyte GA-8SR533P Manual de usuario

Gigabyte

Gigabyte GA-686BLX Manual de usuario

Gigabyte

Gigabyte GA-34SGCM-S2 Manual de usuario

Gigabyte

Gigabyte GA-880GM-D2H Manual de usuario

Gigabyte

Gigabyte GA-MA78GM-S2H Manual

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manual de usuario