Giant GP5128 Manual de instrucciones

Contents:

Installation Instructions: page 2

Pump Specications: page 3

Exploded View: page 4

Parts List: page 5

Kits/Torque Specs: page 5

Repair Instructions: page 6

Dimensions: page 7

Warranty Information back page

Model

GP5128

Triplex Ceramic

Plunger Pump

Operating Instructions /

Manual

Updated 07/18

INSTALLATION INSTRUCTIONS

Figures for speed (rpm) and pressure apply to

interval operation with cold water.

For continual operation, the speed of all pump

models must be limited to 700 rpm and the

max. operating pressure reduced by 10%.

Required NPSH refers to water: Specic weight

1kg/dm3, viscosity 1°E at max. permissible revo-

lutions.

Operation and Maintenance

Check oil level prior to starting and ensure trou-

ble-free water supply. Oil: Use only 1.2 gallons

(4.6 liters) of Industrial Gear Lube Oil (Giant p/n

01154) or ISO VG 220 (e.g. Aral Degol BG220)

or SAE 90 gear oil.

Initial change after 50 operating hours and then

every 500 operating hours.

Caution when operating in damp places or

with high temperature uctuations. Oil must

be changed immediately, should condensate

(frothy oil) occur in the gear box.

Keep NPSH under control.

Max. input pressure 145 PSI (10 bar), max. suc-

tion head -4.35 PSI (-0.3 bar).

Safety Rules

Pump operation without safety valve as well

as any excess in temperature or speed limits

automatically voids the warranty. The safety

valve must be regulated in accordance with

the guidelines for liquid spraying units so that

the admissible operating pressure can not be

exceeded by more than 10%.

When the pump is in operation, the open shaft

end must be covered up by a shaft protector

(21), the driven shaft side and coupling by a

contact-protector.

Pressure in discharge line and in pump must

be at zero before any maintenance to the pump

takes place. Close up suction line. Disconnect

fuses to ensure that the driving motor does not

get switched on accidently.

Make sure that all parts on the pressure side of

the unit are vented and relled, with pressure at

zero, before starting the pump.

In order to prevent air, or an air/water-mixture

being absorbed and to prevent cavitation occur-

ing, te pump-npshr, positive suction head and

water temperature must be kept under control.

Cavitation and/or compression of gases lead

to uncontrollable pressure-kicks which can

ruin pump and unit parts and also be dan-

gerous to the operator or anyone standing

nearby.

Giant plunger pumps are suitable for pump-

ing clean water and other non-agressive or

abrasive media with a specic weight similar to

water.

Before pumping other liquids - especially

inammable, explosive and toxic media - the

pump manufacturer must under all circum-

stances be consulted with regard to the

resistance of the pump material. It is the re-

sponsibility of the equipment manufacturer

and/or operator to ensure that all pertinent

safety regulations are adhered to.

U.S. ......................... (Metric)

Volume.......................................................... 20.6 GPM .............. 78.0 LPM

Discharge Pressure......................................4060 PSI ................. 280 bar

Power Required............................................56.0 BHP................. 41.8 kW

Speed (Continuous)...................................... ................................ 1000 RPM

Inlet Pressure (maximum) ............................-4.35 to145 PSI ...... -0.3 to 10 bar

Plunger Diameter..........................................1.1” .......................... 28 mm

Crankshft Stroke...........................................1.81” ........................ 46 mm

Crankshaft Diameter.....................................1.38” ........................ 35 mm

Crankshaft Mounting ..................................................................... Either side

Shaft Rotation................................................................................ Top of pulley towards manifold

Temperature of Pumped Fluids ....................Up to 140oF ............. (60oC)

Inlet Ports ...................................................................................... (3) 1-1/2” NPT

Discharge Ports............................................................................. (2) 1” NPT

Weight ..........................................................179 lbs. ................... (81 kg)

Crankcase Oil Capacity................................1.2 Gal. ................... (4.6 liter)

Fluid End Material......................................... ................................ Nickel-Plated Spheroidical Cast Iron

Specications

Model GP5128

Consult the factory for special requirements that must be met if the pump is to

operate beyond one or more of the limits specied above.

PULLEY INFORMATION

Pulley selection and pump speed are based on

a 1725 RPM motor and “B” section belts. When

selecting desired GPM, allow for a ±5% tolerance

on pumps output due to variations in pulleys, belts

and motors among manufacturers.

1. Select GPM required, then select appropriate

motor and pump pulley from the same line.

2. The desired pressure is achieved by selecting

the correct nozzle size that corresponds with the

pump GPM.

HORSEPOWER INFORMATION

Horsepower ratings shown are the power re-

quirements for the pump. Gas engine power

outputs must be approximately twice the pump

power requirements shown above.

We recommend that a 1.15 service factor be speci-

ed when selecting an electric motor as the power

source. To compute specic pump horsepower

requirements, use the following formula:

(GPM X PSI) / 1450 = HP

GP5128 Horsepower Requirements

RPM GPM 1000 PSI 2000 PSI 3000 PSI 4060 PSI

600 12.4 8.6 17.1 25.7 34.7

700 14.4 9.9 19.9 29.8 40.3

800 16.5 11.4 22.8 34.1 46.2

900 18.5 12.8 25.5 38.3 51.8

1000 20.6 14.2 28.4 42.6 57.7

GP5128 Exploded View

ITEM PART DESCRIPTION QTY.

1 13266 Crankcase 1

2 13000 Oil Filler Plug Assembly 1

3 05943 Oil Sight Glass Assembly 1

4 13267 Crankcase Cover 1

5 13268 O-Ring 1

8 07105 Oil Dip Stick 1

9 01009 O-Ring, Dip Stick 1

10 07008 Inner Hexagon Screw 4

11 06725 Spring Washer 4

12 07703 Drain Plug, 3/4” BSP 1

13 07704 Gasket, Drain Plug 1

14 13271 Bearing Cover 2

15 13272 Radial Shaft Seal 2

16 08182 O-Ring 2

17 13358 Hexagon Screw 8

18 06725 Spring Washer 8

20 13206 Taper Roller Bearing 2

20A* 13207 Shim, 0.1mm 1-5

20B* 04723 Shim, 0.15mm 1-5

20C* 04724 Shim, 0.2mm 1-5

21 13273 Shaft Protector 1

22 13274 Crankshaft 1

23 13275 Fitting Key 1

24 13276 Connecting Rod Assembly 3

25 13279 Crosshead Assembly 3

28 13281 Crosshead Pin 3

29A 07125 Centering Sleeve 3

29B 13220 Plunger Pipe 3

29C 13031 Tensioning Screw 3

29D 07755 Copper Ring 3

30 13282 Oil Scraper 3

*May not be present

GP5128 Spare Parts List

ITEM PART DESCRIPTION QTY.

30A 05889 Washer for Drip Shield 3

31 13284 Radial Shaft Seal 3

35 04286 Seal Sleeve 3

35B 08183 O-Ring 3

36 13228 Grooved Ring 3

37 04287 Seal Case 3

37A 07700 O-Ring 6

39 13197 Pressure Ring 3

40 13115 V-Sleeve 6

41 13198 Sleeve Support Ring 3

42 07173 Tension Spring 3

43 04288-NPT Valve Casing 1

44 07150 O-Ring 6

45 07109 Plug, 1/2” BSP 1

45A 06272 Copper Seal Ring, 1/2” 1

46 07060 Valve Assembly 6

46A 07064 Valve Seat 6

46B 07063 Valve Plate 6

46C 07062-0100 Valve Spring 6

46D 07066 Spacer Pipe 6

47 04295 Spacer Ring 3

48 04289 Plug 3

48A 07008 Inner Hexagon Screw 12

48B 13012 O-Ring 3

48C 06078 Tension Spring 3

49 13339 Inner Hexagon Screw 8

52 13362 Disc for Crankshaft 1

53 13358 Hexagon Screw 1

54 06626 Plug, 1” NPT 1

55 06627 Plug, 1-1/2” NPT 2

56 07623 Eye Bolt 1

57 04334 Drip Pan 1

GP5128 Repair Kits

Plunger Packing Kit - #09761

Item Part# Description Qty.

35B 08183 O-Ring 3

36 13228 Grooved Ring 3

37A 07700 O-Ring 6

40 13115 V-Sleeve 6

Valve Assembly Kit - #09762

Item Part # Description Qty.

46 07060 Valve Assembly 6

48B 13012 O-Ring 3

Oil Seal Kit - #09230

Item Part # Description Qty.

31 13284 Oil Seal 3

To Check Valves

Remove inner hexagon screw (48A) and remove plugs (48) with a screwdriver. Check O-rings on plugs (48B).

Pull out tension spring (48C). Take spacer pipe (46D) together with the discharge valve out of the valve casing

using a clipring pliers or a ø22 extractor tool. Remove the next exposed spacer pipe and suction valve as already

described. Remove the valve seats (46A) from the spacer pipes by lightly tapping the valve plate (46B) from

above with a plastic rod. Check sealing surfaces and replace worn parts.

When reassembling, use new O-rings if possible and oil them before installing.

Tighten inner hexagon screws (48A) to 35 Ft-Lbs (47NM).

To Check Seals and Plunger Pipe

Loosen the 8 nut and pull off valve casing to the front. Pull seal sleeves (35) out of guides in crankcase and over

the plunger pipe (29B). Pull support ring (41), sleeves (40) and pressure ring (39) out of seal sleeve.

Check plunger surfaces, sleeves (40) and grooved rings (36). Replace worn parts.

If the plunger pipe is worn out, loosen tension screw (29C) and pull off plunger pipe to the front. Clean contact

surfaces of plunger (25) thoroughly. Then place new plunger pipe carefully through the oiled seals into the seal

case. Check O-rings (35A, 35B) on seal sleeves and replace worn O-rings. Then push seal sleeve together with

plunger pipe into the crankcase guide. Turn gear carefully until plunger (25) comes up against the plunger pipe.

Put a new copper gasket (29D) onto the tension screw (29C). Cover the thread of tension screw and the gasket

with glue and tighten to 26 Ft.-lbs. (35NM).

Important! Care must be taken that no glue gets between the plunger pipe (29B) and the centering sleeve

(29A). The plunger pipe should not be strained by eccentric tightening of the tension screw or through damage

to front of surface of plunger, otherwise it will probably break. Tighten the inner screws (49) for the valve casing

evenly to 74-89 Ft.-Lbs. (100-120NM).

To Dismantle Gear

Drain oil after dismantling valve case and plunger pipes and screw off crankcase cover (4) and bearing cover

(14).

Loosen con rod screws (24), push stem of con rod as far as possible into the crosshead guide and carefully

push out the radial shaft seals (31).

Important! Connecting rods are marked for identication. Do not twist con rod halves. Con rod is to be reinstalled

in the same position on shaft journals.

While slightly turning the crankshaft, hit it out carefully to one side with a rubber hammer.

Important! Do not bend con rod shank. Finally, check surfaces of shaft, con rod, crosshead and plungers (25)

as well as radial shaft seals (15, 31) and taper roller bearings (20).

To Reassemble

Using a soft tool, press in the outer bearing ring until it lines up with the outer edge of the bearing hole. Remove

bearing cover together with shaft ring and O-ring. Fit shaft with pressed-on bearing parts through the bearing

hole on the opposite side. Press in outer bearing ring and tension it inwards with the bearing cover, keeping the

shaft in vertical position and turning it slowly so that the taper rollers of the bearings touch the edge of the outer

bearing ring. Adjust axial bearing clearance with tting discs 0.1mm (20A). Shaft should turn easily with very

little clearance. Tighten inner hexagon screws on con rod (24) to 26 Ft.-Lbs. (35NM).

Important! There should be enough clearance for the con rod to move sideways a little on the journals.

Important! The 1/2” BSP connection in the crankcase serves the purpose of draining leakage water. The

connection should not be closed (see the drawing to the right).

GP5128 Repair Instructions

GP5128 Dimensions Inches (mm)

GP5128 Torque Specications/Lubrication Information

Position Item# Description Lubrication Torque Amount

1 13266 Crankcase Molycote Cu-Paste

3 05943 Oil Sight Glass Assembly Loctite 572 22 ft.-lbs. (30 Nm)

10 07008 Inner Hexagon Screw 33 ft.-lbs. (45 Nm)

12 07703 Drain Plug, 3/4” BSP 74 ft.-lbs. (100 Nm)

17 13358 Hexagon Screw 33 ft.-lbs. (45 Nm)

24 13276 Connecting Rod Assy. 22 ft.-lbs. (30 Nm)

31 13284 Radial Shaft Seal Loctite 403

29C 13031 Tension Screw, Plunger Loctite 243 22 ft.-lbs. (30 Nm)

48A 07008 Inner Hexagon Screw, Plug 35 ft.-lbs. (47 Nm)

49 13339 Inner Hexagon Screw, Valve Casing 89 ft.-lbs. (120 Nm)

GIANT INDUSTRIES, INC.,

900 N. Westwood Ave., Toledo, Ohio 43607

Phone (419) 531-4600, FAX (419) 531-6836,

www.giantpumps.com

GIANT INDUSTRIES LIMITED WARRANTY

Giant Industries, Inc. pumps and accessories are warranted by the manufacturer

to be free from defects in workmanship and material as follows:

1.For portable pressure washers and car wash applications, the discharge manifolds

will never fail, period. If they ever fail, we will replace them free of charge. Our other

pump parts, used in portable pressure washers and in car wash applications, are war-

ranted for ve years from the date of shipment for all pumps used in NON-SALINE,

clean water applications.

2. One (1) year from the date of shipment for all other Giant industrial and consumer

pumps.

3. Six (6) months from the date of shipment for all rebuilt pumps.

4. Ninety (90) days from the date of shipment for all Giant accessories.

This warranty is limited to repair or replacement of pumps and accessories of which

the manufacturer’s evaluation shows were defective at the time of shipment by the

manufacturer. The following items are NOT covered or will void the warranty:

1. Defects caused by negligence or fault of the buyer or third party.

2. Normal wear and tear to standard wear parts.

3. Use of repair parts other than those manufactured or authorized by Giant.

4. Improper use of the product as a component part.

5. Changes or modications made by the customer or third party.

6. The operation of pumps and or accessories exceeding the specications set

forth in the Operations Manuals provided by Giant Industries, Inc.

Liability under this warranty is on all non-wear parts and limited to the replace-

ment or repair of those products returned freight prepaid to Giant Industries which are

deemed to be defective due to workmanship or failure of material. A Returned Goods

Authorization (R.G.A.) number and completed warranty evaluation form is required

prior to the return to Giant Industries of all products under warranty consideration. Call

(419)-531-4600 or fax (419)-531-6836 to obtain an R.G.A. number.

Repair or replacement of defective products as provided is the sole and exclusive

remedy provided hereunder and the MANUFACTURER SHALL NOT BE LIABLE FOR

FURTHER LOSS, DAMAGES, OR EXPENSES, INCLUDING INCIDENTAL AND CON-

SEQUENTIAL DAMAGES DIRECTLY OR INDIRECTLY ARISING FROM THE SALE

OR USE OF THIS PRODUCT.

THE LIMITED WARRANTY SET FORTH HEREIN IS IN LIEU OF ALL OTHER

WARRANTIES OR REPRESENTATION, EXPRESS OR IMPLIED, INCLUDING WITH-

OUT LIMITATION ANY WARRANTIES OR MERCHANTABILITY OR FITNESS FOR A

PARTICULAR PURPOSEANDALLSUCH WARRANTIESARE HEREBYDISCLAIMED

AND EXCLUDED BY THE MANUFACTURER.

07/18 GP5128.indd

Tabla de contenidos

Otros manuales de Bomba de agua de Giant

Giant

Giant GP8055-Brine Manual de usuario

Giant

Giant MP Series Manual de usuario

Giant

Giant P55W Manual de instrucciones

Giant

Giant P435-5100 Manual de usuario

Giant

Giant Triplex Ceramic Plunger Pump LP350 Guía de solución de problemas

Giant

Giant P532 Manual de usuario

Giant

Giant SP100W Manual de usuario

Giant

Giant GP7124A-4000 Manual de usuario

Giant

Giant P200A-3100 Series Repair and Guía de configuración

Giant

Giant LP301A-0081 Manual de usuario

Giant

Giant P200 Series Manual de usuario

Giant

Giant P480 Manual de usuario

Giant

Giant LP200-SS Manual de usuario

Giant

Giant GP5132 Manual de instrucciones

Giant

Giant LP122A Series Manual de usuario

Giant

Giant P435-5121 Manual de usuario

Giant

Giant GXR Series Manual de usuario

Giant

Giant LP122A Series Manual de servicio

Giant

Giant P217 Manual de usuario

Giant

Giant P420A-5100 Manual de usuario

Giant

Giant GP7522GB Manual de usuario

Giant

Giant MP Series Manual de usuario

Giant

Giant SP100HT Manual de usuario

Giant

Giant GP7132 Manual de usuario

Manuales populares de Bomba de agua de otras marcas

Neptun

Neptun NPHW 5500 Manual de usuario

Sensidyne

Sensidyne Gilian BDX-II Instrucciones de instalación y funcionamiento

Draper

Draper 47808 Manual de usuario

Trolla

Trolla 12820 Manual de usuario

Sunfab

Sunfab SVH Series Manual de usuario

WilTec

WilTec 50740 Manual de usuario

Fieldmann

Fieldmann FVC 5015 EK Manual de usuario

Everbilt

Everbilt EFSUB5-122HD Manual de usuario

Graco

Graco Husky 3300e Manual de usuario

esotec

esotec 101018 Manual de usuario

moyno

moyno 2000 CC Manual de usuario

Becker

Becker BASIC VASF 2.80/1-0.AC230 Manual de usuario

Sykes AmeriPumps

Sykes AmeriPumps GP100M Guía de solución de problemas

DUROMAX

DUROMAX XP WX Series Manual de usuario

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Manual de usuario

Franklin Electric

Franklin Electric IPS Manual de usuario

Xylem

Xylem e-1532 Series Manual de usuario

Milton Roy

Milton Roy PRIMEROYAL Manual de usuario