Gewiss I-CON BASIC Manual de funcionamiento
JOINON WALLBOX
I-CON BASIC
Manuale di utilizzo ed installazione - User and installation manual - Manuel
d’installation et d’exploitation - Manual de uso e instalación - Installations- und
Bedienungsanleitung - Manual de instalare și instalare -Használati és telepítési
útmutató - Gebruiks- en installatiehandleiding
IT
UNITÀ DI RICARICA VEICOLI ELETTRICI
JOINON WALLBOX I-CON BASIC - JOINON WALLBOX I-CON BASIC RECHARGING UNIT FOR ELECTRIC
VEHICLES - UNITÉ DE RECHARGE DE VÉHICULES ÉLECTRIQUES JOINON WALLBOX I-CON BASIC -
UNIDAD DE CARGA DE VEHÍCULOS ELÉCTRICOS JOINON WALLBOX I-CON BASIC - LADESTATION FÜR
ELEKTROFAHRZEUGE JOINON WALLBOX I-CON BASIC - UNITATE DE REÎNCĂRCARE VEHICULE
ELECTRICE JOINON WALLBOX I-CON BASIC - JOINON WALLBOX I-CON BASIC ELEKTROMOS JÁRMŰ
TÖLTŐEGYSÉG - OPLAADEENHEID VOOR ELEKTRISCHE VOERTUIGEN JOINON WALLBOX I-CON BASIC
EN ES HU
FR DE RO NL
1. INFORMATION ABOUT THIS MANUAL
1.1. Field of application
1.2. Intended users
1.3 Symbols
2. REGULATORY ASPECTS
2.1. Fulfilment of regulations
2.2. Degree of protection
2.3. Pollution rating
2.4. Current socket-outlets
3. SAFETY FUNCTION
3.1. Safety conditions
3.2. Personal protective equipment (PPE)
4. DEVICE DELIVERY AND STORAGE
4.1. Delivery
4.2. Device identification
4.3. Damage during transport
4.4. Storage
5. DEVICE HANDLING
5.1. Transport
5.2. Packaging removal
6. PREPARATION FOR DEVICE INSTALLATION
6.1. Environment
6.2. Environmental conditions
6.3. Support and fastening surface
6.4. Opening the casing
6.5. CLOSING the casing
7. DEVICE INSTALLATION AND CONNECTION
7.1. General installation requirements
7.2. BASIC JOINON WALLBOX I-CON
7.2.1. Device installation
7.2.2. Connection of the device power supply
8. OPERATION AND CHARACTERISTICS
8.1. AUTOSTART
8.2. RFID
8.3. CLOUD OCPP
CONTENTS
JOINON WALLBOX I-CON BASIC recharging unit for electric vehicles
9. STATUS INDICATORS
10. CHARGING PROCESS
10.1. AUTOSTART
10.2. PARKING
10.3. CLOUD PARKING
11. FAULTS AND TROUBLESHOOTING
12. UPDATING THE FIRMWARE
13. MODIFYING THE OPERATING PARAMETERS OF THE RECHARGING STATION
14. DISCONNECTING FROM THE MAINS SUPPLY
15. PREVENTIVE MAINTENANCE
15.1. RESIDUAL CURRENT DEVICES
This manual describes the JOINON I-CON electrical vehicle recharging station and provides the necessary infor-
mation for correct delivery, installation, start-up, maintenance and operation.
1.1 FIELD OF APPLICATION
This manual applies for the following charging stations:
- GWJ3001A – WB ICON AUTOSTART 4kW T2S IP55
- GWJ3002A – WB ICON AUTOSTART 7kW T2S IP55
- GWJ3003A – WB ICON AUTOSTART 11kW T2S IP55
- GWJ3004A – WB ICON AUTOSTART 22kW T2S IP55
- GWJ3011A – WB ICON AUTOSTART 4kW T2C IP55
- GWJ3012A – WB ICON AUTOSTART 7kW T2C IP55
- GWJ3013A – WB ICON AUTOSTART 11kW T2C IP55
- GWJ3014A – WB ICON AUTOSTART 22kW T2C IP55
- GWJ3002R – WB ICON RFID 7kW T2S IP55
- GWJ3004R – WB ICON RFID 22kW T2S IP55
- GWJ3012R – WB ICON RFID 7kW T2C IP55
- GWJ3014R – WB ICON RFID 22kW T2C IP55
- GWJ3002L – WB ICON RFID 7kW T2S IP55 - ETH
- GWJ3004L – WB ICON RFID 22kW T2S IP55 - ETH
- GWJ3012L – WB ICON RFID 7kW T2C IP55 - ETH
- GWJ3014L – WB ICON RFID 22kW T2C IP55 - ETH
- GWJ3002W – WB ICON RFID 7kW T2S IP55 - 4G
- GWJ3004W – WB ICON RFID 22kW T2S IP55 - 4G
- GWJ3012W – WB ICON RFID 7kW T2C IP55 - 4G
- GWJ3014W – WB ICON RFID 22kW T2C IP55 - 4G
1.2 INTENDED USERS
This document is intended for qualified personnel.
When this manual refers to qualified personnel, this means personnel complying with all the standards, directives
and laws concerning safety, as applicable to the installation and operation of this device.
It is recommended to have this device installed by a professional installer.
1.3 SYMBOLS
This manual uses various symbols to stress and highlight certain information.
Their general meaning is indicated below.
General caution
Electric risk
Prohibition
General information
Refer to the indicated section
INFORMATION ABOUT THIS MANUAL
1.
JOINON WALLBOX I-CON BASIC recharging unit for electric vehicles
2.1 FULFILMENT OF REGULATIONS
CE marking
CE marking is essential for marketing the products in question within the European Union and the European Eco-
nomic Area. The charging stations have CE marking as they comply with the following directives:
• Low Voltage Directive 2014/35/EU
• Electromagnetic Compatibility directive 2014/30/EU
• RED directive 2014/53/EU (version with RFID and/or GSM)
Low Voltage directive
The recharging stations comply with this directive as they fulfil the applicable parts of the harmonised standard EN
61851-1 Electric vehicle conductive charging system - Part 1: General requirements
Electromagnetic Compatibility directive
The charging stations comply with this directive, as they fulfil the applicable parts of the harmonised standards:
• IEC 61851-21-2 Electric vehicle conductive charging system - Part 21-2: Electric vehicle requirements for
conductive connection to an AC/DC supply - EMC requirements for o board electric vehicle charging systems
• EN 61000-6-1 Electromagnetic compatibility. Part 6-1: Generic standards - Immunity for residential, commer-
cial and light-industrial environments
• EN 61000-6-3 Electromagnetic compatibility. Part 6-3: Generic standards - Emissions for residential, commer-
cial and light-industrial environments
RED directive
The charging stations comply with this directive, as they fulfil the applicable parts of the harmonised standards:
• ETSI EN 300 330V 2.1.1
• ETSI EN 301 511 V 12.1.10 (GSM)
Fulfilment with this standard requires compliance with the requirements and procedures of the other standards
in the same series.
2.2. DEGREE OF PROTECTION
These charging stations have an IP55 degree of protection against external agents.
This device is designed for indoor and outdoor use.
2.3. POLLUTION RATING
The pollution degree that these stations are designed for is level 3 with reference to Standard IEC 60664-1.
2.4. CURRENT SOCKET-OUTLETS
The charging stations can be supplied with various connector configurations, depending on the customer's require-
ments.
The following connectors are available:
REGULATORY ASPECTS
2.
IEC 62196-2 Type 2 - cable + mobile connector
IEC 62196-2 Type 2 - flush-mounting version
This section describes the safety warnings and the personal protective equipment.
3.1. SAFETY CONDITIONS
General warnings
Potential hazards for people
In order to protect your own safety, observe the following warnings.
SAFETY FUNCTION
3.
The operations described in this manual may only be performed by duly qualified personnel.
When this manual refers to qualified personnel, this means personnel complying with all the standards, directives and laws
concerning safety, as applicable to the installation and operation of this device.
The selection of qualified personnel is always the responsibility of the company that carries out the work, which is the only
party that can decide whether a worker is capable of doing a certain job, thereby ensuring their safety and respecting the
applicable law with regards safety in the workplace.
These companies must provide suitable training regarding the electrical devices for their personnel, and make sure they
become familiar with the content of this manual.
It is mandatory to comply with the applicable safety laws relating to electrical work. There is the risk of possible electrical
shock.
Risk of electric shock.
Compliance with the safety instructions provided in this manual or by the legislation indicated does not imply exemption
from compliance with other specific standards regarding the installation, location, country or other circumstances that
concern the device.
The opening of the casing does not imply the absence of voltage inside.
Interventions must only be carried out once the voltage supply to the system has been cut o using a device that can
guarantee insulation.
It may only be opened by qualified personnel, following the instructions given in this manual.
It is mandatory to read and understand all parts of this manual before starting to handle, install or use the unit.
Gewiss disclaims all liability for any damage caused by inappropriate use of the charging stations. Any operation carried
out on these charging stations that involves a change to the original electrical settings must be authorised by Gewiss
beforehand. All such proposals must be examined and approved by Gewiss.
Before carrying out any interventions, cut o the voltage supply to the system using a device that can guarantee insulation.
As the minimum safety measure for this operation, observe the following rules:
1. Cut o the voltage supply.
2. Prevent the reactivation of the power supply.
3. Check there is no voltage.
4. Protect yourself against energised elements nearby, and place safety signals to mark o the work area if
necessary.
Until these steps have been applied, the product must be considered powered; no interventions are therefore authorised.
HAZARD: crushing and injury of limbs.
Always follow the instructions supplied in the manual for device handling and positioning.
The weight of the device can cause injuries if not handled correctly.
JOINON WALLBOX I-CON BASIC recharging unit for electric vehicles
Potential hazards for the device
In order to protect the device, observe the following warnings.
3.2. PERSONAL PROTECTIVE EQUIPMENT (PPE)
When working on the device, use at least the following items of safety equipment.
Name Explanation
Safety footwear In accordance with UNE-EN-ISO 20345:2012 or the latest edition published
Helmet In accordance with EN 397:1995 or the latest edition published
Helmet with a face mask In accordance with UNE-EN 166:2002 or the latest edition published, if there are live elements
that can be directly accessed.
Work garments Close-fitting and non-flammable, in 100% cotton
Dielectric gloves In accordance with EN 60903:2005 or the latest edition published
The equipment or devices used for operations with the system energised must have at least category III-1000 Volt insulation.
If the regulations in the location of installation require other types of personal protective equipment, the equipment must be
integrated in a suitable manner.
Before reconnecting the voltage supply after any duly authorised operation, make sure the device is ready to start working.
Then, connect it following the instructions in the manual.
Do not touch the boards or the electronic components; the more sensitive components may get damaged or be destroyed
by static electricity.
Do not disconnect or connect any terminal while the device is operating. Disconnect and check for the absence of voltage
before performing any operation.
4.1. DELIVERY
Keep the device packaged until installation.
4.2. DEVICE IDENTIFICATION
The serial number of the device identifies it in an unequivocal manner. In any communication with Gewiss, refer-
ence must be made to this number.
The device serial number is indicated with a data matrix on the technical data label (on the side of the front panel).
4.3. DAMAGE DURING TRANSPORT
If the device was damaged during transport:
1. Do not install it.
2. Notify the fact immediately (within 5 days of delivery).
If it is necessary to return the device to the manufacturer, the original packaging must be used.
4.4. STORAGE
Failure to observe the instructions provided in this section could cause damage to the device. The manufac-
turer declines all responsibility for damage deriving from the failure to observe these instructions.
If the device is not installed immediately upon delivery, to avoid its deterioration, proceed as indicated below:
• To correctly conserve the charging station, do not remove the original packaging until the moment it is installed.
• Deterioration of the packaging (cuts, holes, etc.) prevents the correct conservation of the charging station prior
to installation. The manufacturer declines all responsibility relative to the consequences caused by packaging
deterioration.
• Keep the device clean (remove dust, chips, grease, etc.) and avoid the presence of rodents.
• Protect it against water spray, welding sparks, etc.
• Cover the device with a protective breathable material to avoid condensation caused by environmental humidity.
• Charging stations kept in a warehouse must not be subjected to climatic conditions other than those indicated
below:
Ambient storage conditions
Minimum temperature -40°C
Minimum temperature of the surrounding
air
-40°C
Maximum temperature of the surrounding
air
70°C
Maximum relative humidity without con-
densation
95%
• It is very important to protect the system against corrosive chemical products and saline environments.
DEVICE DELIVERY AND STORAGE
4.
JOINON WALLBOX I-CON BASIC recharging unit for electric vehicles
DEVICE HANDLING
5. During transport, the device must be protected against mechanical shocks, vibrations, water spray (rain) and any
other product or situation able to damage it or alter its behaviour. Failure to respect these instructions could cause
the product warranty to be cancelled without the manufacturer bearing any liability.
5.1. TRANSPORT
Handling the unpackaged device
At least the following provisions must be observed:
1. Follow the fundamental ergonomic recommendations to avoid injuries when lifting weights.
2. Do not release the device until it is perfectly fastened or positioned.
3. Follow the instructions of another person who guides the movements to be made.
5.2. PACKAGING REMOVAL
The correct handling of the charging stations is very important to:
• Avoid damaging the packaging that maintains their optimum condition, from shipment to the moment they are
installed.
• Avoid striking or dropping the mechanical stations as this could deteriorate the mechanical properties.
• Avoid, as far as possible, the vibrations that could cause subsequent abnormal operation.
If a fault is discovered, contact Gewiss immediately.
Packaging disposal
The packaging can be sent to an authorised non-hazardous waste agent.
In any case, each part of the packaging must be disposed of as follows:
• Plastic (polystyrene, plastic bags and bubble wrap): relative container.
• Cardboard: relative container.
To decide the location of the device and prepare for its installation, a series of instructions connected to the prop-
erties of the device must be followed.
6.1. ENVIRONMENT
• Position the charging station in a location that can be accessed for installation and maintenance, which permits
its use and the reading of the LED indicators.
• Avoid corrosive environments that could have an influence on the correct operation of the device.
• It is prohibited to leave any object on the device.
PREPARATION FOR DEVICE INSTALLATION
6.
6.2. ENVIRONMENTAL CONDITIONS
To select the most suitable location, take the environmental operating conditions of the device into consideration.
Environmental conditions
Minimum temperature -25°C
Minimum temperature of the surrounding
air
-25°C
Maximum temperature of the surrounding
air
+50°C
Maximum relative humidity without con-
densation
95%
NOTE= if the ambient temperature is higher than 40°C, a cover must be installed to protect the device from direct
sunlight.
Remember that it could occasionally produce a small amount of condensation as a result of temperature changes.
Therefore, in addition to the protection it has, the charging stations must be monitored when they are used in
areas where it is probable that not all the previously indicated conditions will be satisfied.
Never connect the device to the voltage supply when there is condensation.
6.3. SUPPORT AND FASTENING SURFACE
To ensure correct heat dispersal and a good hold, the recharging stations must be installed on a perfectly vertical
wall.
The wall on which the device is fastened must be solid. It must be possible to drill the wall and insert wall plugs
and anchor bolts that are suitable for supporting the device weight.
Tabla de contenidos
Otros manuales de Cargador de baterías de Gewiss
Gewiss
Gewiss GW68122 Manual de funcionamiento
Gewiss
Gewiss JOINON EASY Series Manual de funcionamiento
Gewiss
Gewiss JOINON I-CON PREMIUM GWJ3201A Manual de funcionamiento
Gewiss
Gewiss JOINON WALLBOX I-CON DLM Manual de usuario
Gewiss
Gewiss GWJ3001A Manual de funcionamiento
Gewiss
Gewiss JOINON I-CON Manual de funcionamiento
Gewiss
Gewiss JOINON Manual de usuario
