Geemarc AMPLICALL 101 Manual de usuario
0
Wireless doorbell
Sonnette sans fil
Drahtlose Türklingel
Deutsch P23
English P1
Français P12
1
!!! Please refer to our website:
www.geemarc.com for an up to date user guide,
as there may be important updates and changes
you need to be aware of !!!
PACKAGE CONTENTS
The package contains the following items:
1user’smanual
1 AMPLICALLTM101 (AC101)
2 screws and 2 fixing holes
1 wall bracket and 1 lanyard bracket.
2
DESCRIPTION
Light
Indicator
Push button
Battery
compartment
Battery cover
Mounting
holes
Mounting bracket
Lock
lever
3
INSTALLATION
Battery installation or replacement in the remote
AMPLICALLTM101
4
1. Use your finger to unlock the lock lever (fig ).
2. Rotate the mounting bracket to 90 degrees (fig ).
3. Remove the mounting bracket from the unit (fig ).
4. Rotate the battery cover using a coin (fig ).
5. Insert a CR2032 battery into the battery compartment with the
polarity + on top. (fig ).
6. Close the battery cover using a coin. (fig ).
7. Replace the mounting bracket to 90 degrees. (fig ).
8. Rotate the mounting bracket until the part locks.
Note: Low Battery Signal
When the AC101 is running low on battery, it will send a signal to
the AMPLICALLTM100 or AMPLICALLTM150 which will make the
corresponding zone icon light up. To replace the battery, you will
need to follow the 8 steps procedure described above.
5
CODE CONFLICT
If the bell press coding is the same as another transmitter you must
change the code. When you have changed the code must re-pair
the bell press.
(A) Open the battery cover.
(B) Take out the battery.
(C) Press and hold the test button, insert the battery whilst holding
the button for 5 seconds. The LED will flash 5 times when a
new code is generated.
6
Pairing with AMPLICALLTM100/AMPLICALLTM150
Enter pairing mode on the AC100 or AC150:
1. Press & hold the LEARNING button (●) for 3 seconds. The
LED in zone icon #1 will flash.
2. Press the LEARNING button (●)
again to move to the zone icon
you wish to pair the AC101 with
Press the melody selection
() button to scroll through the
melodies. Once you hear a
melody you like, do not press
any button during the melody.
3. Press once the doorbell button
of the AC101 to pair.
4. If successful, the AMPLICALL100 or 150 will generate two short
tones.
Zone
selector
Learning
button
Melody
selector
7
WALL MOUNTED INSTALLATION
Mounting with screws
Requires an electric drill to fix the AC101 on the wall using the
provided ram plug and screws.
8
Mounting with Double-sided adhesive
You can install your AMPLICALLTM101 onto a wall.
Please, follow the recommendations below.
Attach the Doorbell to the mounting bracket
1. Replace the mounting bracket to 90 degrees. (fig 1).
2. Rotate the mounting bracket until the part locks. (fig 2).
Fig1 Fig2
9
Put the bell press to the lanyard bracket
1. Place the lanyard bracket to 90 degrees.
2. Rotate the mounting bracket until the part locks.
GUARANTEE
From the moment your Geemarc AMPLICALLTM101 is purchased,
Geemarc guarantee is for the period of two years. During this time,
all repairs or replacements (at our discretion) are free of charge.
Should you experience a problem then contact our help line or visit
Tabla de contenidos
Idiomas:
Otros manuales de Accesorios de Geemarc
Geemarc
Geemarc Doorbell595 U.L.E Manual de instrucciones
Geemarc
Geemarc Doorbell595 U.L.E Manual de instrucciones
Geemarc
Geemarc ClearSound Amplicall1 Manual de usuario
Geemarc
Geemarc Doorbell595 U.L.E. Manual de instrucciones
Geemarc
Geemarc Doorbell595 U.L.E Manual de instrucciones
Geemarc
Geemarc CL2 Manual de instalación y operación
