Gear4music DD400X Manual de usuario
DIGITAL DRUM KIT
SETUPGUIDE
DD400X
DRUM MODULE BOX
X1 Drum Module
ACCESSORIES BOX
1. X3 Cymbal Holders
2. X1 Drum Key
3. X1 Snare Metal Rod
(165mm)
4. X1 Pair Drumsticks
5. X2 Handscrew
6. X4 Tom & Module
Metal Rod (110mm)
7. X1 AC Adaptor
8. Owner’s Manual
9. Setup Guide
10. X9 Connection
Cables
STAND AND CYMBAL HOLDER BOX
1. X6 Holder Clamp
2. Left Side Arm
3. Right Side Arm
4. Center Pipe
5. Left Pillar
6. Right Pillar
2
CONTENTS CHECKLIST
Your kit will arrive in one box and should take
around 30 minutes to fully assemble. Please
check that all the items below are present before
assembly and follow the instructions carefully.
CYMBAL PAD BOX
X1 Cymbal Pad for Hi-Hat
X1 Cymbal Pad for Ride
X1 Cymbal Pad for Crash
DRUM PAD BOX
X3 Tom Pad
X1 Snare Pad
BASS DRUM BOX
X1 Bass Drum Pedal
HI-HAT PEDAL BOX
X1 Hi-Hat Control Pedal
1 2 34
567
8910
1
1
5 6
2
4
3
3
ATTACH THE PARTS
ATTACH THE PADS
1. Loosen wing nut on the holder clamp, which is
on the left and right side arm.
2. Insert the Snare Lmetal rod into the holder
clamp on the left side arm, then insert the Tom
& Module L-metal rod into the holder clamp on
the center pipe and right side arm. Tighten wing
nuts on the holder clamp.
3. Attach drum pads to the Snare L-Metal rod and
the Tom & Module L-Metal rods then tighten
wing nuts. Repeat for each pad.
ATTACH THE CYMBAL PADS
1. Loosen wing nut on the holder clamp on left
pillar, right pillar and left side arm.
2. Insert each cymbal holder into left pillar, right
pillar, left side arm and tighten wing nut.
3. Remove wing nut and felt washer from cymbal
holder.
4. Place cymbal pad on tilter assembly. Re-attach
the felt washer and wing nut. Tighten wing nut.
1
1
2
1
3
4
1
3
2
2
3
HI-HAT
CRASH RIDE
4
DRUM MODULE
ATTACH THE DRUM MODULE
1. Loosen wing nut on the center pipe clamp.
2. Insert the L-metal rod into the clamp.
3. Place the drum module onto the L-metal rod.
4. Tighten the wing nut on the clamp.
CONNECTION PROCEDURE
1. Place the pedal on the floor on your left side.
2. Place the bass drum pedal on the floor in the
center of rack.
3. Please connect the clearly marked cables from
the pads to the correct inputs on the drum
module.
1
3
4
2
BASS DRUM PEDALHI-HAT PEDAL
CRASH 1
CRASH 2
HI-HAT
TOM 1
SNARE
HI-HAT PEDAL
BASS PEDAL
TOM 3
TOM 2
If you have any more questions about this product, please do not hesitate to contact the
Tabla de contenidos
Otros manuales de Tambor de Gear4music
Gear4music
Gear4music JDD200 Manual de usuario
Gear4music
Gear4music VISIONPAD-6 Manual de usuario
Gear4music
Gear4music FUSION DRUM KIT Manual de usuario
Gear4music
Gear4music BDK STARTER KIT Manual de usuario
Gear4music
Gear4music CHILDREN’S DRUM KIT Manual de usuario
Gear4music
Gear4music DD40 Manual de usuario
Gear4music
Gear4music JUNIOR 3 PIECE DRUM KIT Manual de usuario
Gear4music
Gear4music DD220X Manual de usuario
Gear4music
Gear4music DD400+ Manual de usuario
Gear4music
Gear4music JUNIOR 5 PIECE DRUM KIT Manual de usuario
