GEA HGX22P CO2 Series Manual de usuario

96019-05.2012-DGbFEI

engineering for a better world GEA Refrigeration Technologies

Bock Compressor HGX22P CO2

Assembly instructions

HGX22P/110-4 CO2

HGX22P/125-4 CO2

HGX22P/160-4 CO2

HGX22P/190-4 CO2

1 1

96019-05.2012-DGbFEI

About these instructions

Read these instructions before assembly and before using the compressor. This will avoid misunder-

standings and prevent damage. Improper assembly and use of the compressor can result in serious

or fatal injury.

Observe the safety instructions contained in these instructions.

These instructions must be passed onto the end customer along with the unit in which the compres-

sor is installed.

GEA Bock GmbH

72636 Frickenhausen

GEA Bock GmbH

Benzstraße 7

72636 Frickenhausen

Germany

Telephone +49 7022 9454 0

Fax +49 7022 9454 137

[email protected]

www.bock.de

Manufacturer

Contact

96019-05.2012-DGbFEI

Contents Page

1 Safety 4

 1.1 Identicationofsafetyinstructions

 1.2 Qualicationsrequiredofpersonnel

1.3 General safety instructions

1.4 Intended use

2 Product description 6

2.1 Short description

2.2 Name plate

2.3 Type key

3 Areas of application 8

3.1 Refrigerants

3.2 Oil charge

3.3 Limits of application

4Compressor assembly 10

4.1 Setting up

4.2 Pipe connections

4.3 Pipes

4.4 Laying suction and pressure lines

4.5 Operating the shut-off valves

4.6 Operating mode of the lockable service connections

5 Electrical connection 12

5.1 Information for contactor and motor contactor selection

5.2 Connection of the driving motor

5.3 Circuit diagram for direct start 230 V Δ/ 400 V Y

5.4 Electronic trigger unit MP 10

5.5 Connection of the electronic trigger unit MP 10

5.6 Functional test of the electronic trigger unit MP 10

5.7 Oil sump heater

6 Commissioning 18

6.1 Preparations for start-up

6.2 Pressure strength test

6.3 Leak test

6.4 Evacuation

6.5 Refrigerant charge

6.6 Start-up

6.7 Decompression valves

6.8 Avoiding slugging

6.9 Connection of oil level regulator

7 Maintenance 20

7.1 Preparation

7.2 Work to be carried out

7.3 Spare parts recommendation

7.4 Accessories

7.5 Extract from the lubricants table

7.6 Decommissioning

8 Technical data 24

9 Dimensions and connections 25

10 Declaration of conformity and installation 26

11 Service 27

96019-05.2012-DGbFEI

1|Safety

1.2 Qualicationsrequiredofpersonnel

1.3 General safety instructions

WARNING! Inadequately qualied personnel poses the risk of accidents, the

consequence being serious or fatal injury. Work on compressors

mustthereforeonlybeperformedbypersonnelwiththequalica-

tions listed below:

 •For example, a refrigeration technician, refrigeration mechatron-

icsengineer.Aswellasprofessionswithcomparabletraining,which

enablepersonneltoassemble,install,maintainandrepairrefrigeration

and air-conditioning systems. Personnel must be capable of assessing

thework to be carried out and recognising any potential dangers.

WARNING! •Refrigerating compressors are pressurised machines and

thereforerequireparticularcautionandcareinhandling.

•Risk of burns! Depending on the operating conditions, surface

temperatures of over 60 °C on the pressure side or below 0 °C on

the suction side can be reached.

•The maximum permissible overpressure must not be exceeded,

even for testing purposes.

1.1 Identicationofsafetyinstructions:

DANGER! Indicatesadangeroussituationwhich,ifnot

 avoided,willcauseimmediatefatalorseriousinjury.

WARNING!

 Indicatesadangeroussituationwhich,ifnot

 avoided,maycausefatalorseriousinjury.

CAUTION!

 Indicatesadangeroussituationwhich,ifnot

 avoided,maycausefairlysevereorminorinjury.

ATTENTION! Indicatesasituationwhich,ifnot

 avoided,maycausepropertydamage.

INFO! Importantinformationortipsonsimplifyingwork.

WARNING! DANGER OF SUFFOCATION!

 NeverreleasesignicantvolumesofCO2or the entire contents of

the system into closed rooms!

96019-05.2012-DGbFEI

1|Safety

These assembly instructions describe the standard version of the HGX22P -CO2manufactured by

Bock.

The compressor is intended for use with CO2in sub-critical systems in compliance with the limits of

application.

Onlytherefrigerantspeciedintheseinstructionsmaybeused.

Any other use of the compressor is prohibited!

1.4 Intended use

WARNING! The compressor may not be used in potentially explosive

environments!

The Bock refrigerating compressor named in the title is intended for installing in a machine (within

theEUaccordingtotheEUDirectives2006/42/ECMachineryDirective,97/23/ECPressureEquipment

Directive and 2006/95/EC – Low Voltage Directive).

Commissioning is only permissible if the compressor has been installed in accordance with these

assembly instructions and the entire system into which it is integrated has been inspected and

approved in accordance with legal regulations.

96019-05.2012-DGbFEI

1 1

Name plate

Fig. 1

Fig. 2

Oil sight glass

Valve plate

Cylinder cover

Discharge

shut-off valve

Oil pump

Terminal box

Suction

shut-off valve

Drive section

Motor section

Dimension and connection values can be found in Chapter 9

Transport eyelet

2|Product description

• Semi-hermetictwo-cylinderreciprocatingcompressorwithoilpumplubrication.

• Suction gas cooled drive motor.

2.1 Short description

96019-05.2012-DGbFEI

2|Product description

2.2 Name plate (example)

2.3 Typekey (example)

¹) HG - Hermetic Gas-Cooled (suction gas-cooled)

²) X - Ester oil charge

³) Additional declaration for Pluscom compressors

Fig. 3

1 Typedesignation 6 Voltage,circuit,frequency

2 Machine number 7 Nominal rotation speed

3 maximum operating current 8 Displacement

4 Startingcurrent(rotorblocked) 9 Voltage,circuit,frequency

5 ND (LP): max. permissible operating 10 Nominal rotation speed

pressure (g) Low pressure side 11 Displacement

HD (HP):

max. permissible operating

 12 Oiltypelledatthefactory

pressur

e(g) High pressure side 13 Terminal box protection type

Observe the limits of application Electrical accessories can change

diagrams! the IP protection class!

50 Hz

}

60 Hz

}

HG 22 P 125- 4CO2

CO2Version

Number of poles

Swept volume

³)

Numbers of cylinders

Size

Oil charge ²)

Series ¹)

513

40/55

AS33567A001

C85E

20,9/12,1A

Δ: 121A Y: 70A

GEA Bock GmbH

72636 Frickenhausen, Germany

96019-05.2012-DGbFEI

3|Areas of application

ATTENTION! Compressor operation is possible within the operating limits

shown in the diagrams. Please note the signicance

of the shaded areas. Thresholds should not be selected as design

or continuous operation points.

- Max. permissible discharge end temperature 140 °C

    -Max.permissibleswitchingfrequency8x/h.

- A minimum running time of 3 min. steady-state condition

(continuous operation) must be achieved.

Foroperationwithfrequencyconverter:

- The maximum current and power consumption must not be

exceeded. Inthecaseofoperationabove themainsfrequency,

the application limit can therefore be limited.

 Thecompressorsarelledatthefactorywiththefollowingoiltype:

BockC85E(onlythisoilmaybeused)

3.1 Refrigerants

• CO2: R744

3.2 Oil charge

3.3 Limits of application

R744

Max. permissible operating

pressure (LP/HP)1): 40/55 bar

Unlimited application range

1) LP = Low pressure

HP = High pressure

Fig. 4

Evaporation temperature (°C)

Condensing temperature (°C)

Suction gas superheat (K)

Suction gas temperature (°C)

96019-05.2012-DGbFEI

4|Compressor assembly

4.1 Setting up

 Setuponanevensurfaceorframewithsufcientload-

bearing capacity.

Single compressor preferably on vibration damper.

Duplex and parallel circuits always rigid.

Use transport eyelet.

Do not lift manually!

Use lifting gear!

 Provideadequateclearanceformaintenancework.

 Ensureadequatecompressorventilation.

 Donotuseinacorrosive,dusty,dampatmosphereora

combustible environment.

Fig. 5

Fig. 6

Fig. 7

Fig. 8

4.2 Pipe connections

The pipe connections have graduated inside diameters so that pipes with

standart millimetre and inch dimansions can be used.

The connection diameters of the shut-off valves are rated for maximum

compressor output. Theactualrequiredpipecrosssectionmustbe

matched to the output. The same applies for non-return valves.

Fig. 9: graduated

internal diameter

Tol.-Ang. DIN ISO 2768-mK

Ra Rz

Maß

Passung

Freigabe

Alternativbezug:

Baumustergeprüft

Teil inaktiv

Lieferantenzeichnung

K.-Auftrag:

PL:

Zeichnung ungültig

Entwicklungsstand

Teil keine Serie

120

400

±0.5

über 0.5

bis 6

Benzstraße 7 - 72636 Frickenhausen - Germany - www.bock.de

Unbemaßte Radien:

Diese Zeichnung ist unser Eigentum!

Sie darf ohne unsere Genehmigung weder nach-

gebildet, vervielfältigt, oder Dritten Personen zu-

gänglich gemacht werden. Der Nachbau nach

dieser Zeichnung, oder an Hand der nach dieser

Zeichnung hergestellten Gegenstände durch den

Abnehmer oder Dritte ist nicht gestattet.

Wir behalten uns alle Rechte, gemäß DIN ISO 16016

an dieser Zeichnung vor.

Bearb.

Datum

Änderungs-Nr.

Werkstoff:

Ausgangsteil, bzw. Rohteil:

Gepr.

Name

Datum

19.04.

Werkstückkanten

DIN ISO 13715

Ersatz für:

Ersetzt durch:

Erstellt

2010

Geprüft

Kurz

Zone

1/x

Oberflächenbehandlung / Härte:

Blatt:

Änderungsbeschreibung

400

Benennung:

±0.8

1000

±0.3

120

±0.2

Zeichn.-Nr. Teile-Nr.

Oberflächenangaben ISO 1302

x.xxxx-xxxxx.x

Zust.

Gußtoleranzen:

Gewicht: (kg)

±0.1

Maßstab:

1:1

Wasserwaage

für Indesign

Der Lieferant muß sicherstellen, dass die Ware in

einwandfreiem Zustand angeliefert wird (Korrosions-

schutz, Verpackung für sicheren Transport).

Rz 25

Rz 160

0,05

Rz 1,6

0,3

0,7

1,6

Rz 16

6,3

Rz 63

Rz 6,3

Rz 12,5

F:\user\kurz\3D Sachen\3D Teile\Zeichnungen\Wasserwaage

INFO! Newcompressorsarefactory-lledwithinertgas(3barnitrogen).

Leave this service charge in the compressor for as long as possible

and prevent the ingress of air.

  Check the compressor for transport damage before starting any

 work.

ATTENTION! Do not solder as long as the compressor is under pressure.

Superheating can damage the valve. Remove the pipe supports

therefore from the valve for soldering and accordingly cool

the valve body during and after soldering.

Only solder using inert gas to inhibit oxidation products (scale).

96019-05.2012-DGbFEI

4.4 Laying suction and pressure lines

INFO! Proper layout of the suction and pressure lines directly after the

compressor is integral to the smooth running and vibration behaviour

of the system.

ATTENTION! Improperly installed pipescancause cracks and tearswhichcan

result in a loss of refrigerant.

A rule of thumb:

Alwayslaytherstpipesectionstartingfromtheshut-offvalvedownwards and

parallel to the drive shaft.

4|Compressor assembly

4.3 Pipes

 Pipesandsystemcomponentsmustbecleananddryinsideandfreeofscale,swarfandlayersof

rust and phosphate. Only use air-tight parts.

Lay pipes correctly. Suitable vibration compensators must be provided to prevent pipes being

cracked and broken by severe vibrations.

Ensure a proper oil return.

Keep pressure losses to an absolute minimum.

Fig. 10

Rigid

fixed point

As short as

possible

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Compresor de aire de GEA

GEA

GEA HG34P/e Manual de usuario

GEA

GEA Bock HGX46 CO2 T Series Manual de usuario

GEA

GEA Grasso M-Series Manual de usuario

GEA

GEA FK20 Manual de usuario

GEA

GEA HA4 Manual de usuario

GEA

GEA Bock HG8 Series Manual de usuario

GEA

GEA Bock HG8 Series Manual de usuario

GEA

GEA Grasso RC9 Series Manual de usuario

GEA

GEA HGX46/280-4 ML CO2T Manual de usuario

GEA

GEA Grasso Manual de usuario

GEA

GEA HG12P Manual de usuario

GEA

GEA HGX34/130-4 ML CO2 T Manual de usuario

GEA

GEA HG7 Manual de usuario

GEA

GEA Bock HGX2 CO2 T Series Manual de usuario

GEA

GEA FK40/560 N Manual de usuario

GEA

GEA Bock F76 Series Manual de usuario

GEA

GEA HGX34/110-4 ML CO2 T Manual de usuario

GEA

GEA HGX6 R134a series Manual de usuario

GEA

GEA Grasso VHS Series Manual de usuario

GEA

GEA Grasso 5 Manual de usuario

GEA

GEA HGX12P CO2 Manual de usuario

GEA

GEA HGX5/725-4 R134a Manual de usuario

GEA

GEA HG6/1080-4 Manual de usuario

GEA

GEA GEA Bock HG66e Series Manual de usuario

Manuales populares de Compresor de aire de otras marcas

Sparmax

Sparmax DC-25XR Manual de usuario

KAESER

KAESER M122 Manual de usuario

GMC

GMC GAC1500 Manual de usuario

Briggs & Stratton

Briggs & Stratton Air Compressor Manual de usuario

Fini

Fini F3GST2TK Manual de usuario

Industrial Air

Industrial Air CP1580325 Manual de programación

Campbell Hausfeld

Campbell Hausfeld RP3300 Guía de inicio rápido

Ingersoll-Rand

Ingersoll-Rand UP6 20 HP Manual de usuario

Hitachi

Hitachi EC99S Manual del operador

Parkside

Parkside PKO 270 A1 Manual de usuario

Sullair

Sullair 185 Manual de usuario

Clas Ohlson

Clas Ohlson QIE-ZTH-15 Manual de usuario

Ferm

Ferm CRM1046 Manual de usuario

BE AC153 Manual de usuario

RIDGID

RIDGID OF25150A Manual de usuario

Johnson Controls

Johnson Controls QUANTUM LX Manual

Sears

Sears Craftsman 919.167463 Manual de usuario

Ring Automotive

Ring Automotive RAC700 Manual de usuario