GE GN75DNSRSA01 Manual de usuario

IMPORTANTSAFETYINFORMATION.

READALL INSTRUCTIONSBEFOREUSING.

INSTALLER: Leave this manual with the

appliance.

CONSUMER: Retain this manual for future

reference.

WARNING: iftheinformation

in this manual is not followed exactly,

afire or explosion may result causing

property damage, personal injury

or death.

-- Do not store or use gasoline or other

flammable vapors and liquids in the

vicinitg of this or ang other appliance.

-WHAT TODO IF YOU

SMELL GAS

[] Do not trg to light amatch, or cigarette,

or turn on ang gas or electrical appliance.

[]Do not touch ang electrical switch;

do not use ang phone in gour building.

[] Clear the room, building or area of all

occupants.

[] Immediatelg call gout gas supplier from

a neighbor's phone. Follow the gas

supplier's instructions carefullg.

] lf gou cannot reach gour gas supplier,

call the fire department.

-- Installation and service must be

performed bg a qualified installer,

service agencg or the gas supplier.

ANSI Z21103 • CSA 43

WARNING! or oursafety,

the information in this manual must be followed to

minimize the risk of fire or explosion, electric shock,

or to prevent propertg domoge, personol injurg or

loss of life.

Error codes, ge.com

Thiswater heater hasthe abilitgto check its own operation

continuouslg. If a fault occurs,an error code willflash on the

displag of the remote control onlgwhen the water isrunning.

Thisassistswith diagnosing the fault, and mag enable gou to

overcome a problem without a servicecall. Pleaseidentifg the

code displaged when inquiring about service.

Error Code Table

WARNING: Someof the checks below mag

need to be done bg a qualified service technician.

02 No burner operation during freeze •

protection mode

10 Air supplg or exhaust blockage •

11 No ignition •

12 Flame failure •

14 Thermal fuse

16 Over temperature warning

32-72

LC(001 Scale buildup in heat exchanger

No code Nothing happens when water flow is activated

Checkthat the gas isturned on at the water heater,gas meter or cglindeE

Ifthe sgstem ispropane, make sure gas is inthe tank.

Callfor service.

EnsureGE-approvedventing materials are being used.

Checkthat nothing isblocking the flue inlet or exhaust.

Checkall vent components for proper connections.

Checkthat the gas isturned on at the water heater,gas meter or cglindeE

Ifthe sgstem ispropane, make sure gas is inthe tank.

Ensureappliance is properlg grounded.

Checkthat the gas isturned on at the water heater,gas meter or cglindeE

Checkfor obstructions in the flue outlet. Ifthe sgstem ispropane, make sure

gas isin the tank.

Ensureappliance is properlg grounded.

Callfor service.

Checkfor restrictions in air flow around unit and vent outlet.

Checkfor foreign materials in exhaust piping.

Callfor service.

Seepage 11for Flushing Procedures.

Clean inletwater supplgfiltec

On new installations, ensure hot and cold water linesare not reversed.

Ensuregou have at least the minimum flow rate requiredto firethe unit.

Water quality.

Carefor gour water heater should include

evaluation of water qualitg. Ifthe water exceeds

the target levelsprovided inthe table, gou should

treat or condition the water.

If gou are in a hard water area,it isrecommended

to installa GEwater softener prior to the water

heater

fb_

_P aterfilter

Watersoftener

MAXIMUM LEVEL

Total Hardness Up to 200 mg/L (12 grains)

Aluminum* Up to 0.2 mg/L

Chlorides* Up to 250 mg/L

Copper* Up to 1.0 mg/L

Iron* Up to 0.3 mg/L

Manganese* Up to 0.05 mg/L

pH* 6.5 to 8.5

TDS(Total Dissolved Solids)* Up to 500 mg/L

Zinc* Up to 5 mg/L

* Source:Part 1/43National Secondarg Drinking Water Regulations

Flushing the heat exchanger(errorcode LCor00). ge.com

-& WARNING: Beforeperforming this action,first remove power

to the water heater in order to prevent an accidental scald injury.

NOTE:GErecommends that this task be performed bg a trained serviceproviden

An "LC"or "00"error code indicatesthe unit isbeginning to have water hardness coat

the heat exchanger and must be flushed. Failureto flush the appliance will cause

damage to the heat exchanger.Damage causedbg water hardness isnot covered bg

the unit'swarrantg. After flushing,reset the LCfault codebg turning off the power to

the unit and turning the power back on.

E] Disconnectelectrical power to the water heaten

[] Closethe shut-off valveson both the hotwater and cold water lines(V3and V4).

I-_ Connectpump outlet hose (H1)to the cold water line at servicevalve V2.

[] Connectdrain hose(H3)to servicevalve V1.

[] Pourapproximatelg 4 gallonsof virgin, food-grade white vinegar or citric acid

into pail.

[] Placethe drain hose (H3)and the hose(H2)to the pump inletinto the cleaning

solution.

[] Openboth servicevalves(Vl and V2)on the hot water and cold water lines.

F] Operatethe pump and allow the cleaning solutionto circulate through the water

heater for 45 minutes.

[] Turn off the pump.

[T_ Rinsethe cleaning solution from the water

heater bg:

a. removing the free end of the drain

hose(H3)from the pail,

b. closingservice valve V2and opening

shut-off valve V4(do not open shut-off

valve V3),

O O

Water Heater

O O

Hot Water Line

Gas Supply

-0 V4 I

Cold Water Line

c. allowing water to flow through

the water heater for 5 minutes, Circulating

d. closing service valve Vl and opening

shut-off valve VS.

D Disconnectall hoses.

i_ Removethe in-line filter at the cold

water inlet and clean out ang residue.

5 gallon pail of

virgin,food grade

white vinegar {or

virgin,food grade

citric acid)

Placethe filter back into the unit. Seepage 7.

i_l Restoreelectrical power to the water

heater.

KEY

151 3/4"BallValve

3/4" Union

?"'--d Check Valve

z_ Pressure Relief Valve

Pressure Regulator

Circulating Pump

t_:_ Boiler Drain Valve

[_ Solenoid Valve

Before you callfor service.., gecom

Troubleshooting Tips

Save time and mone_l! Review the chart below first and you

may not need to call for service.

Possible Causes What ToDo

Thereis no hot water There isno gas, water or • Hake suregas,water and power are turned on.

when tap is opened electricitg flowing to unit.

Thesgstemrequires • Ensurefaucet aerators areclean and faucet flows at least

approximatelg 0.6gpm 0.6gpm of hot water.

minimum flow to activate •Duringsummer months, increase the temperature setting

the heater, at the control or increasethe water flow.

Water gets cold when If the fiow from the tap was • Duringsummer months, increase the temperature setting

hot water isbeing used adjusted to lessen it, the flow at the controlor increasethe water flow.

mag have gone below the • Water flow might be increased bg cleaning the aerators

minimum required, on the faucets.

White smoke comes out During colder weather, when

ofthe exhaust the exhausttemperature ismuch

hotter than the outside air, the

exhaust fumes condense,

producing water vapor.

When ohot tap is

opened, hot water

does not come out

immediately

Hot water must travel through the

plumbing from the water heater to

the faucet, The time period for hot

water to reach the fixture is determined

bg the amount of water in the plumbing

sgstem between the water heater and the

fixture, water pressure and the flow rate

of the fixture.

After hot water top is

turned off, fan on water

heater continues to run

Thefan isdesignedto continue running

for a short time after the flow of water stops.

This is to ensure constant water temperatures

during rapid starting and stopping, as well as

exhausting ang residual gas flue products

from the unit,

Display shows

temperatures between

37°and 60_.

Control isdisplaging temperature • Change control to Fahrenheit.Seepage 6.

in Celsius.

Technicaldata.

PRESSURE DROP CURVE

.J 15

_ lO

£L

GN75 ]

_ GN94/GP94 60

0.0 2.0 4.0 6.0 8.0 10.0

Water Flow (gpm)

OUTLET FLOW DATA

__k_

\x\

I I

50 "_

..C

40 "-_

30 ¢

20 ,-

(3-

I I

w__m

__m

25 50 75 100 125 150

delta T -Temperature Rise (°F)

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Calentador de agua de GE

GE 40M06AAG Instrucciones de montaje

GE GEH50DEEJS Manual de usuario

GE GP40T06AVR Instrucciones de montaje

GE 50T06TAG Instrucciones de montaje

GE GP30T06AVJ Instrucciones de montaje

GE SG50T12AVG Instrucciones de montaje

GE Appliances GEH5ODNSRSA Instrucciones de funcionamiento

GE GG40S06TVT Instrucciones de montaje

GE GG50S06TVT Instrucciones de montaje

GE GEH80DEEJS Instrucciones originales

GE GE50T BQT Series Manual de usuario

GE GG30S BXR Series Manual de usuario

GE GG48T06AXK Instrucciones de montaje

GE GP40T06PVT Instrucciones de montaje

GE GeoSpring GEH50DEED Manual de usuario

GE GE30T06MAG Instrucciones de montaje

GE GeoSpring GEH50DXSRGA Instrucciones originales

GE GP40S06TVT Instrucciones de montaje

GE GG50T06TVG Instrucciones de montaje

GE PR06DSATB Series Manual de usuario

GE SG60T12YVK Instrucciones de montaje

GE GE02P08BAR Manual de usuario

GE GG30S BXR Series Manual de usuario

GE PG50T09AVH Instrucciones de montaje

Manuales populares de Calentador de agua de otras marcas

Kenmore

Kenmore 153.582400 Manual de usuario

Applimo

Applimo Edel AIR Manual de usuario

STIEBEL ELTRON

STIEBEL ELTRON Eltronom SHU 5 S Manual de usuario

clage

clage E-Mini Series Manual de usuario

Toyotomi

Toyotomi Oil Miser OM-180 Manual de usuario

Bradford White

Bradford White EF Series Manual de usuario

Eccotemp

Eccotemp 40-H Manual de usuario

Dimplex

Dimplex ECSd125-580 Guía

Dux

Dux 32FCR6N Manual de usuario

Toyotomi

Toyotomi Oil Miser OM-148 (Type D) Guía de solución de problemas

Noritz

Noritz N-132M Manual de instrucciones

TESY

TESY GCV7/4S 10047 Hoja de especificaciones

A.O. Smith

A.O. Smith Gphe 50 Manual de usuario

Koryo

Koryo KWHZF15Y Manual de usuario

Pentair

Pentair PSC-14-4-02 Manual de usuario

Thermor

Thermor AEROMAX SPLIT 2 Manual de usuario

American Hometec

American Hometec AHQ-B03X Manual de usuario

PVI

PVI MAXIM Manual de usuario