GE 29292 Manual de usuario
29292
Caller ID BedroomPhone™
with Dual-Wake Alarms
User's Guide
We bring good things to life.
2
FCC NUMBER IS LOCATED ON THE CABINET BOTTOM
REN NUMBER IS LOCATED ON THE CABINET BOTTOM
FCC REGISTRATION INFORMATION
Your telephone equipment is registered with the Federal Communications Commission and is in compliance with parts 15
and 68, FCC Rules and Regulations.
1Notification to the Local Telephone Company
On the bottom of this equipment is a label indicating, among other information, the FCC Registration number and
Ringer Equivalence Number (REN) for the equipment. You must, upon request, provide this information to your
telephone company.
The REN is useful in determining the number of devices you may connect to your telephone line and still have all of
these devices ring when your telephone number is called. In most (but not all) areas, the sum of the RENs of all devices
connected to one line should not exceed 5. To be certain of the number of devices you may connect to your line as
determined by the REN, you should contact your local telephone company.
Notes
• This equipment may not be used on coin service provided by the telephone company.
• Party lines are subject to state tariffs, and therefore, you may not be able to use your own telephone equipment if you
are on a party line. Check with your local telephone company.
• Notice must be given to the telephone company upon permanent disconnection of your telephone from your line.
2Rights of the Telephone Company
Should your equipment cause trouble on your line which may harm the telephone network, the telephone company
shall, where practicable, notify you that temporary discontinuance of service may be required. Where prior notice is not
practicable and the circumstances warrant such action, the telephone company may temporarily discontinue service
immediately. In case of such temporary discontinuance, the telephone company must: (1) promptly notify you of such
temporary discontinuance; (2) afford you the opportunity to correct the situation; and (3) inform you of your right to
bring a complaint to the Commission pursuant to procedures set forth in Subpart E of Part 68, FCC Rules and
Regulations.
The telephone company may make changes in its communications facilities, equipment, operations of procedures
where such action is required in the operation of its business and not inconsistent with FCC Rules and Regulations. If
these changes are expected to affect the use or performance of your telephone equipment, thetelephone company must
give you adequate notice, in writing, to allow you to maintain uninterrupted service.
INTERFERENCE INFORMATION
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may
not cause harmful interference; and (2) This device must accept any interference received, including interference that may
cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna (that is, the antenna for radio or television that is “receiving” the
interference).
• Reorient or relocate and increase the separation between the telecommunications equipment and receiving antenna.
• Connect the telecommunications equipment into an outlet on a circuit different from that to which the receiving antenna
is connected.
If these measures do not eliminate the interference, please consult your dealer or an experienced radio/television
technician for additional suggestions. Also, the Federal Communications Commission has prepared a helpful booklet,
“How To Identify and Resolve Radio/TV Interference Problems.” This booklet is available from the U.S. Government
Printing Office, Washington, D.C. 20402. Please specify stock number 004-000-00345-4 when ordering copies.
HEARING AID COMPATIBILITY
This telephone system meets FCC standards for Hearing Aid Compatibility.
3
TABLE OF CONTENTS
FCC REGISTRATION INFORMATION .... 2
INTERFERENCE INFORMATION ............ 2
HEARING AID COMPATIBILITY ........... 2
BEFORE YOU BEGIN .............................. 4
PARTS CHECKLIST ............................. 4
MODULAR JACK REQUIREMENTS ......... 4
DESKTOP INSTALLATION ......................... 5
POWERING UP..................................... 6
“NOWORRY” BATTERY BACKUP ........ 6
SETUP ................................................ 8
SETTING THE TIME AND DATE ............. 8
SETTING THE DISPLAY CONTRAST ........ 9
SETTING YOUR LOCAL AREA CODE ...... 9
SETTING THE LANGUAGE .................. 10
SETTING THE DISPLAY BACKLIGHT ...... 10
ALARM BASICS .................................. 11
SETTING THE ALARM TIME ............... 11
ALARM SELECT .............................. 11
TURNING OFF THE ALARMS .............. 11
USING THE SNOOZE TIMER ............... 12
ADJUSTING THE SNOOZE TIMER ........ 12
TELEPHONE BASICS ............................. 13
SETTING THE RINGER VOLUME .......... 13
SETTING THE HANDSET VOLUME ....... 13
TONE/PULSE DIALING ...................... 13
TEMPORARY TONE .......................... 14
FLASH ........................................... 14
REDIAL .......................................... 14
CALLER ID FEATURES .......................... 15
SUMMARY SCREEN ......................... 15
RECEIVING AND STORING CALLS ........ 16
REVIEWING CALL RECORDS ............... 16
DELETING CALL RECORDS ................ 17
DIALING BACK ................................ 17
IFYOU PROGRAMMED YOUR LOCAL
AREA CODE IN THE SETUP MENU .. 17
IFYOU DID NOT PROGRAM YOUR
LOCAL AREA CODE IN THE
SETUP MENU ........................... 19
MESSAGE INDICATORS ......................... 20
MEMORY........................................... 21
STORING ANUMBER IN MEMORY ... 21
CHANGING ASTORED NUMBER ...... 22
ERASING ASTORED NUMBER ........ 22
DIALING AQUICK DIAL NUMBER .... 22
DIALING STORED NUMBERS .......... 23
INSERTING APAUSE IN THE DIALING
SEQUENCE .............................. 23
CHAIN DIALING FROM MEMORY ..... 24
TROUBLESHOOTING TIPS ...................... 25
GENERAL PRODUCT CARE .................... 27
SERVICE ............................................ 27
INDEX ............................................... 28
LIMITED WARRANTY ............................ 30
WARNING: TO PREVENT FIRE
OR ELECTRICAL SHOCK HAZARD,
DO NOT EXPOSE THIS PRODUCT
TO RAIN OR MOISTURE.
SEE MARKING ON BOTTOM / BACK OF PRODUCT
CAUTION
RISKOFELECTRICSHOCK
DONOTOPEN
THE EXCLAMATION
POINT WITHIN THE
TRIANGLE IS A
WARNING SIGN
ALERTING YOU OF
IMPORTANT
INSTRUCTIONS
ACCOMPANYING
THE PRODUCT.
THE LIGHTNING
FLASH AND ARROW-
HEAD WITHIN THE
TRIANGLE IS A
WARNING SIGN
ALERTING YOU OF
"DANGEROUS
VOLTAGE" INSIDE
THE PRODUCT.
CAUTION: TO REDUCE THE
RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER
(OR BACK). NO USER-
SERVICEABLE PARTS IN-
SIDE. REFER SERVICING
TO QUALIFIED SERVICE
PERSONNEL.
4
Base AC power supply
Handset Line cord
redial storememory
tone oper
*0#
tuv
8
wx
yz
9
pq
rs
7
jkl
5
mno
6
ghi
4
abc
2
def
31
abc
flash
alarm
set
2
1
alarm off
delete
vip/dial
SNOOZE
review
BEFORE YOU BEGIN
PARTS CHECKLIST
Make sure your package includes the following items:
MODULAR JACK REQUIREMENTS
You need an RJ11 type modular jack, which is the most
common type of phone jack and might look like the one
pictured here. If you don’t have a modular jack, call your
local phone company to find out how to get one
installed.
Handset cord
5
CAUTION: Use only the ATLINKS USA 5-2498 power supply that came with this
unit. Using other power supplies may damage the unit.
DESKTOP INSTALLATION
1. Plug the handset cord into the handset. Plug the other end into the jack on the back of the
base.
2. Place the handset in the base.
3. Set the TONE/PULSE switch on the side of the handset to TONE for touch-tone service, or
PULSE for rotary service. If you don't know which type of service you have, check with the
phone company.
4. Plug the telephone line cord into the PHONE LINE jack on the back of the base. Plug the
other end into a modular wall jack.
5. Plug the power supply cord into the back of the base. Plug the other end into an AC outlet.
6. Set the RINGER and DISPLAY switches on the side of the base to the desired settings.
7. Set the VOL switch on the side of the handset to the desired setting.
14
7
5
6
3
2
6
“NOWORRY” BATTERY BACKUP
This clock phone is equipped with a memory holding
system that can be powered with a customer-installed
9-volt alkaline battery (not included).
When power is interrupted, or AC line cord is
unplugged, the battery will power the clock to keep track
of time and alarm settings programmed into memory.
When on battery power, the digital display will not light;
however, should wake time occur during the power
interruption, the alarm will sound if remaining battery
power is adequate. Normal operation will resume after
AC power is restored.
Install battery as follows:
1. Remove the battery cover located on the bottom of
the base.
2. Connect a fresh 9-volt alkaline battery (not included).
The large and small contacts on the battery clip and
the battery will interlock. Once connected, place the
battery inside the battery compartment.
3. Replace the battery cover.
POWERING UP
-
-
+
+
Battery clip
Battery
Battery compartment
7
NOTE: Alkaline (NEDA 1604A) batteries are
recommended. Carbon-zinc (NEDA 1604) batteries may
be used but memory holding time will be substantially
reduced. Memory holding time for a fresh alkaline battery
is approximately 8 hours (if Wake System is not activated),
which should take care of short, nuisance-type AC power
failures. To preserve battery life, the phone should
remain plugged into an AC outlet. As the battery gets
older, its voltage will drop and memory may be lost. Be
sure to replace the battery periodically. Battery is not
included with this clock phone.
All memory will be lost if the battery is not installed while
the unit is unplugged for more than 60 seconds
IMPORTANT: If storing this unit for more than 30 days,
remove the battery.
8
SETUP
SETTING THE TIME AND DATE
NOTE: The telephone company sends the time and date
with the Caller ID information. The unit automatically sets
the time and date when the first call is received (if it has not
already been set).
TIME
1. Press and release the SET button until
SET REAL
TIME
is displayed.
2. Use the REVIEW buttons to adjust the time. The hours
automatically change when the minutes go higher
than 59 or lower than 00.
3. When finished, press SET to confirm. Now you’re
ready to enter the month.
MONTH
1. Use the REVIEW buttons to set the month.
2. When finished, press SET to confirm. Now you’re
ready to change the day.
DAY
1. Use the REVIEW buttons to set the day.
2. When finished, press SET to confirm.
alarm
set
2
1
alarm off
delete
vip/dial
SNOOZE
review
SET button REVIEW buttons
9
SETTING THE DISPLAY CONTRAST
This setting allows you to adjust the display contrast for
easier viewing.
1. Press and release the SET button until
SET
CONTRAST
is displayed.
2. Use the REVIEW buttons to select the desired setting
(1-5).
3. When finished, press SET to confirm.
SETTING YOUR LOCAL AREA CODE
1. Press and release the SET button until
SET AREA
CODE
is displayed.
2. Use the REVIEW buttons to select the first digit.
3. Once the first digit is set, press SET.
4. Repeat steps 2-3 until all the digits of the area code
are set.
When finished, press SET to confirm.
alarm
set
2
1
alarm off
delete
vip/dial
SNOOZE
review
SET button REVIEW buttons
10
SETTING THE LANGUAGE
This adjustment changes the prompts to be displayed in
English, French, or Spanish.
1. Press and hold the SET button until
SET LANGUAGE
is displayed.
2. Use the REVIEW buttons to select the desired
language.
3. When finished, press SET to confirm.
SETTING THE DISPLAY BACKLIGHT
Set the DISPLAY switch on the side of the base to adjust
the backlighting when the unit is plugged into an AC
outlet. It can be set to LO or HI.
alarm
set
2
1
alarm off
delete
vip/dial
SNOOZE
review
SET button REVIEW buttons
DISPLAY switch
display lo hi ringer off lo hi
Tabla de contenidos
Idiomas:
Otros manuales de Teléfono de GE
GE
GE 29115AE1 Manual de usuario
GE
GE 2-9233 Manual de usuario
GE
GE ProSeries 2-9435 Manual de usuario
GE
GE 29579 Manual de usuario
GE
GE 29484 Manual de usuario
GE
GE 2-9268B Manual de usuario
GE
GE 27851GE2 Manual de usuario
GE
GE FOLD 2-9180 Manual de usuario
GE
GE 29253GC1 Manual de usuario
GE
GE 2-9950 Manual de usuario
GE
GE 30385EE1 Manual de usuario
GE
GE 740 Manual de usuario
GE
GE Model 29318 Manual de usuario
GE
GE 27881GE2 Manual de usuario
GE
GE 29438 Manual de usuario
GE
GE 30524EE4 Manual de usuario
GE
GE InfoLink 28320 Manual de usuario
GE
GE 29418 Manual de usuario
GE
GE 2-9831 Manual de usuario
GE
GE 2-9315 Manual de usuario
