GE RGA720EK Guía de instalación

Este manual sirve para los siguientes modelos

3

Tabla de contenidos

Manuales populares de Rango de otras marcas

Samsung

Samsung FCQ321HTUW Manual de usuario

Kenmore

Kenmore 790.45712 Manual de usuario

Wolf

Wolf CHR CHSSR Manual de usuario

Smeg

Smeg Built-in Microwave Oven Manual de instrucciones

Zanussi

Zanussi ZCG054G Manual de usuario

Whirlpool

Whirlpool 8575985-W Manual de lista de piezas

Frigidaire

Frigidaire 316000635 Manual de usuario

Samsung

Samsung NX58M9960P series Manual de usuario

Hotpoint

Hotpoint RB524R Guía de instalación

Whirlpool

Whirlpool Roper FGP305KW3 Manual de usuario

Amana

Amana ART6610 SERIES Manual de usuario

Maytag

Maytag MERH770WB Manual de usuario

Fulgor Milano

Fulgor Milano SOFIA Manual de usuario

Premier

Premier EF-4358GH Manual de usuario

Kenmore

Kenmore 790.9010 Series Manual de usuario

KitchenAid

KitchenAid KESC300 Manual de usuario

Frigidaire

Frigidaire FFEF3012LS Guía del usuario

Diamond

Diamond G65/2F4T Manual de usuario

GE Appliances

General Electric Company

Louisville, Kentucky 40225

GE CONFIDENTIAL AND PROPRIETARY INFORMATION – NOT FOR PUBLIC DISCLOSURE

GE Consumer & Industrial

20-in. and 24-in.

Compact Gas Range

Model Introduction

TB 01-06

Training Bulletin

January 2006

INTRODUCTION

GE is producing new 20-in. and 24-in. Compact

Gas Ranges, which are available with a standing

pilot or electronic ignition. They also come

standard with 2 oven racks, recessed lift-up

cooktop, separate lower broiler drawer and

removable oven door. The 4 top burners are rated

at 9,100 BTU (natural gas) and 8,000 BTU (LP).

The oven is rated at 13,000 BTU (natural gas) and

13,000 BTU (LP).

Models:

RGA720EK - 20-in. Electronic Ignition

RGA720PK - 20-in. Standing Pilot

RGA724EK - 24-in. Electronic Ignition

RGA724PK - 24-in. Standing Pilot

SERIAL NUMBER

The model/serial tag is located under the cooktop,

on top of the burner box.

TECHNICAL DATA SHEET

The technical data sheet is located on the back of

the range, near the top.

Technical Data Sheet

– 2 –

MANIFOLD PANEL

There are 8 screws that hold the manifold panel in

place.

4 Screws (Behind the Gas Control Knobs)

4 Screws (Top and Bottom of the Manifold Panel)

SWITCH REMOVAL

1. Prop open the cooktop.

2. Remove the gas control knobs, then remove the

manifold panel.

3. To remove the switch, rotate the switch 15-20

degrees counterclockwise and pull the switch off

the manifold.

Note:

For switches located behind the bracket, the

valve must ﬁrst be removed from the manifold.

All 4 switches come as an assembly.

•

•

TOP BURNER VALVE REMOVAL

1. Remove the switch from the valve. (See Switch

Removal.)

2. For the desired valve, remove the 1/4-in. hex-

head screw on the manifold.

3. Lift burners off the oriﬁces, then locate the

oriﬁce that corresponds to the desired valve.

4. Remove the 3/4-in. hex nut holding the oriﬁce

and tube assembly as shown.

Bracket

– 3 –

5. Push oriﬁce down through burner box and

remove the tube assembly from the range.

6. Use a 1/2-in. wrench to remove the valve from

the gas line.

SPARK MODULE

The spark module is located on the back of the

oven, near the bottom. It is protected by a metal

housing. The spark module is mounted with two

tabs, which snap into corresponding slots. To

remove the module, use a ﬂat blade screwdriver to

bend the tabs toward the module body and release

the tab from the slot.

Spark Module

SPARK ELECTRODES

The range has 2 spark electrodes. They have

different part numbers due to wire length. The wires

are held in a retaining clip below the burner box.

The burner box must be removed to route the wires

correctly when replacing an electrode.

Spark Electrodes

When replacing the spark electrodes, tie a string to

the spark electrode wire as shown. From the top of

the range, pull the spark electrode wire up through

the range. Use the string to pull the new spark

electrode wire back through the range.

Spark Electrode Wire

String

Housing

– 4 –

LP CONVERSION

The LP oriﬁces are located in a small pack on the

back of the oven next to the gas regulator. Use a

1/2-in. open end wrench to install the oriﬁces. Turn

the oriﬁce clockwise until snug.

OVEN CAPILLARY

The oven capillary is held in by 2 clips. To remove

the capillary, squeeze both clips at the same time

and gently pull the capillary away from the oven

wall.

OVEN DOOR GASKET

The oven door gasket is held in place by spring

clips. To remove it, place a ﬁnger under the gasket

beside each clip and gently pull straight out.

BROILER DOOR REMOVAL

Open the broiler door and insert a pin into each

door hinge as shown. Remove the 2 Phillips head

screws from each hinge. Slide the drawer off the

hinges.

Capillary

Clip

Screws

Pin

– 5 –

Wiring Diagram

– 6 –

Schematic