GE CARESCAPE Manual de usuario
CARESCAPE ONE
Clinical Reference Guide
Software Version 3.0
gehealthcare.com
ii
Notice
The materials contained in this document are intended for educational purposes only. This document does not
establish specications, operating procedures or maintenance methods for any of the products referenced.
Always refer to the ocial written materials (labeling) provided with the product for specications, operating
procedures and maintenance requirements.
iii
CARESCAPE ONE ................................. 1
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
CARESCAPE ONE System Components ............2
CARESCAPE ONE Front, Back, and Side Views . . . . . 3
Docking ...........................................4
Turning the CARESCAPE ONE On/O . . . . . . . . . . . . . . 5
Inserting and Removing a Battery..................5
CARESCAPE ONE Monitoring Basics ...............6
Proles ............................................9
Starting Monitoring...............................10
Entering Patient Data.............................11
Resetting a Case / Discharging a Patient . . . . . . . . . . 12
Standby ..........................................13
Alarms ...........................................14
Pausing Alarms ..................................14
Adjusting the Alarm Volume ......................14
Changing an Alarm Limit..........................15
CARESCAPE CO2Measurement ..................16
Trends............................................17
Transport Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Contents
1
CARESCAPE ONE
Overview
The CARESCAPE ONE (CS ONE) can be used as an accessory to the B850/B650/B450 monitor with version 3.1
software, or as a standalone monitor. As a standalone monitor, the CS ONE provides ECG, ST segment, arrhythmia
detection, impedance respiration, SpO2, non-invasive blood pressure, invasive pressure, temperature, and CO2
airway gas parameter acquisition and monitoring.
The CS ONE includes an integrated display, touchscreen, alarm light, user input buttons, and an audio subsystem.
Realtime physiological parameter measurements and waveforms are displayed on the integrated display. Visual
alarms are conveyed using both the integrated display and alarm light. Audible alarms are conveyed using the
integrated audio subsystem. User input for conguration control and interaction is provided via the touchscreen.
In addition, both a power button and touchscreen lock button are provided.
CARESCAPE ONE • Front View
2
CARESCAPE ONE System Components
Your system may not include all these components. Consult your local representative for the available components.
1. CARESCAPE ONE
2. CARESCAPE F0 Dock: Provides powered
docking and battery charging for CS ONE.
3. Mini Dock: Provides unpowered docking for
CS ONE.
4. Parameter Dock 1 and Parameter
Dock 5: Allows CARESCAPE Parameters
to be mounted.
5. CARESCAPE Parameters used with CS ONE:
• CARESCAPE ECG
• CARESCAPE Pressure
• CARESCAPE Temperature
• CARESCAPE CO2
• CARESCAPE SpO2
• CARESCAPE SpO2– Masimo
• CARESCAPE SpO2– Nellcor
12
3
4
5
3
CARESCAPE ONE Front, Back, and Side Views
Front and Back Views
1. Alarm light area (blue, yellow, or red).
2. Audio alarm paused/o indicator (blue).
3. Battery status indicator (yellow or green).
4. Power on/standby button.
On/standby (yellow): The yellow on/
standby key should be lit when one of the
following occurs:
• The device is connected to an
external power source and the device
is turned o
• The device is booting up or is in standby
On/standby (green): The green on/
standby key indicates the device is ready
for operation.
On/standby (unlit): The unlit on/standby
key indicates there is no power applied to
the device.
5. Screen lock/unlock button.
6. Pull tab for removing the acquisition platform from
the docking mount.
7. Battery door.
8. Docking interface connector to the CARESCAPE
Dock F0 or Mini Dock.
Side View
1. CARESCAPE Parameter connectors.
2. Analog out / Debrillator synchronization connector.
Connect IEC 60601-1 complaint medical devices to
this port only.
3. NIBP hose connector.
6
1
2
3
4
7
8
5
1
2
3
4
Docking
Connecting the CARESCAPE ONE to a Dock
To connect the CS ONE to a dock:
1. Align the CS ONE with the dock rails.
2. Push the CS ONE into the dock until it stops.
You will hear a click when it is fully docked.
Disconnecting the CARESCAPE ONE from a Dock
To disconnect the CS ONE from a dock:
1. Pull the tab out and slide the CS ONE out of the
dock rails.
2. Hold onto the CS ONE to make sure it does not drop
when it comes out.
1
1
2
Click
Back view of the
CARESCAPE ONE
Back view of the
CARESCAPE ONE
Front view of the
CARESCAPE ONE
Front view of the
CARESCAPE ONE
5
Turning the CARESCAPE ONE On/O
Turning On the CARESCAPE ONE
CS ONE can operate via battery power using its own
battery, or via DC power when connected to a powered
docking station.
1. Ensure all cables are properly connected.
2. Press the on/standby button on the handle side of
the CS ONE. The welcome screen will appear.
Turning O the CARESCAPE ONE
1. Ensure that the patient has been discharged/the
case has ended.
2. Press the on/standby button for approximately
1 second.
The Powering Down window appears to conrm
you want to shut down the CS ONE.
3. Press the on/standby button again within 10
seconds to shut down the CS ONE.
If you do not press the on/standby button again
within 10 seconds, the CS ONE remains on and the
Powering Down window is removed from
the display.
Inserting and Removing
a Battery
Caution: To prevent loss of monitoring, or the
CS ONE from powering down, change the CS ONE
battery when the CS ONE is connected to a powered
CS ONE dock F0.
Inserting a Battery
1. Open the battery door by gently pulling on the
battery door pull tab.
2. Position the battery with the connector end facing
towards the battery slot and insert the battery all
the way into the battery slot.
Removing a Battery
1. Open the battery door by gently pulling on the
battery door pull tab.
2. Pull on the battery cord to remove the battery from
the battery slot.
2
1
2
6
CARESCAPE ONE Monitoring Basics
CARESCAPE ONE Main Screen Layout
The main screen displays alarms, information, waveforms, parameter windows, and the main menu in
pre-dened areas.
1. Alarm area
2. Information area
3. Waveform area.
4. Upper parameter windows
5. Lower parameter windows
(optional).
6. Main menu area
Information Area
When the Information area of the screen is selected via touch, it opens the Admit/Discharge or Case Setup
menu and provides access to settings related to patient information, standby and prole selections.
The Information area of the screen
displays the following information:
• Patient name (if entered).
The patient name may be
covered by an alarm message
if there are three or more active
alarms.
• Prole name that is being used
for patient monitoring. The
prole name may be covered by
an alarm message if there are
three or more active alarms.
• Patient icon . You can
access the Admit/Discharge or
Case Setup menu by selecting
this icon.
• Battery icon . You can access
the Battery Status menu by
selecting this icon.
• Current time of day.
12
34
5
6
Otros manuales para CARESCAPE
2
Tabla de contenidos
Otros manuales de Monitor de GE
GE
GE KITCHEN HUB UVH1301 Manual de usuario
GE
GE Bently Nevada 1900/27 Manual de usuario
GE
GE Bently Nevada 3300/25 Manual de usuario
GE
GE IC754VBB06CTD Manual de usuario
GE
GE CareScape V100 Manual de usuario
GE
GE HDTV Monitor Manual de usuario
GE
GE Bently Nevada 3300/03 Manual de usuario
GE
GE EPM 3000P Manual de usuario
GE
GE Kelman Minitrans Manual de usuario
GE
GE IC755CS06RD Series Manual de usuario
GE
GE QuickPanel+ IC755CxS06RDx Manual de usuario
GE
GE 3500/40M Manual de usuario
GE
GE Aritech ATS1100 Manual de usuario
GE
GE Corometrics 250cx Series Manual de usuario
GE
GE B40 Manual de usuario
GE
GE Dash 3000 Manual de usuario
GE
GE TMO2D Manual de usuario
GE
GE HandHeld Display (HHD) Manual de usuario
GE
GE Dash 3000 Manual de usuario
GE
GE Responder 2000 Manual de usuario
