GE Monogram ZX27CTYSS Manual de usuario
GE Monogram
®
Assembly Instructions
Before you Begin – Read these instructions completely and carefully.
Note To Installer: Be sure to leave these instructions with the Consumer.
Note to Consumer: Keep these instructions with your Use and Care Book for future reference.
Assembly of this grill cart requires basic mechanical
skills. Proper assembly is the responsibility of the
installer.
NOTE:
This cart must be completely assembled before any
gas connections are made.
If you have questions concerning the installation of
this product, call the GE Answer Center®Consumer
Information Service at 800.626.2000, 24 hours a day,
7 days a week.
If you received a damaged Grill Cart, you should
contact your dealer.
Step 1:
Remove
Packaging
Open the box and remove the contents.
Remove packaging and protective film from
all parts.
Shelf Handle
Shelf
Back Brace
Bottom/Base Panel
Wheels
Front Panel
Caster with Lock
Locate the hardware accessory package and check contents.
Side Braces
Front Brace
Left Side Panel
Right Side Panel
Axle
1/4-20 x 1/2 Bolts
Count 36
32 required, 4 extra
1/4-20 x 3/4 Bolts
Count 2
no extra
Wheel Caps
Count 2
Black Plastic
Grommet
Count 1
#10 Washers
Count 12
8 required, 4 extra
1/4 Washers
Count 40
32 required, 8 extra
Self-tapping Screws
Count 2
1/4-20 Nuts
Count 36
32 required, 4 extra
10-24 Nuts
Count 10
8 required, 2 extra
Black Plastic
Bezels
Count 2
Phillips Head Screws
Count 10
8 required, 2 extra
Caster
27" Outdoor Cooking Center
Grill Cart
Model ZX27CTYSS
2
Installation
27" Grill Cart Assembly
• Two 7/16" wrenches
• 3/8" wrench or socket
• Phillips head screwdriver
• Rubber or wooden mallet
• Gloves to protect against sharp edges
10-24 Nuts
Phillips
Head
Screws #10 Washers
USE
8
EACH
•Locate the bottom/base panel and one side
brace.
•Place the front of the base towards you.
(The front side has 6 screw holes on each
side.)
•Select the caster with lock on the side.
•Place the caster below the front side of the
base, aligned with 4 screw holes.
•Place a side brace on top of the base at the
left side with screw holes aligned.
•Install 4 phillips head screws through the
caster into the base and through the brace.
•Secure screws with flat washers and nuts on
top of the brace. Do not tighten.
•Install the other caster to opposite end of
the brace following the same procedure.
Bottom Panel
1/4-20 x 1/2
Bolts 1/4 Washer 1/4-20 Nuts
USE
4
EACH
•Install front brace to base with 4 bolts and
washers through the top and secure with
nuts on the bottom. Do not tighten.
1/4-20 x 1/2
Bolts 1/4 Washer 1/4-20 Nuts
USE
8
EACH
•Install right side brace to the base by
installing 8 bolts and washers through the
top and secure with nuts on the bottom.
Again, do not tighten.
•Adjust brace alignment by tapping and
sliding until corners meet. Tighten all
screws.
CAUTION: The grill is extremely heavy. 2
people are required to lift and place the grill
onto the cart.
Tools
You Will
Need
Step 2:
Install
Casters
and Braces
to Base
3
Installation
27" Grill Cart Assembly
Step 3:
Install Side
Panels
to Base
•Flatten the carton to use as a pad.
•Stand the assembled base on end.
•Secure left and right side panels to the
bottom panel with 4 bolts, washers and nuts
(2 on each side). Note: Right side panel has
a hole near the center.
•Install bolt and washer from the bottom and
into the base, secure with nuts inside. Do not
tighten.
1/4-20 x 1/2
Bolts 1/4 Washer 1/4-20 Nuts
USE
4
EACH
Step 4:
Install
Front Panel
to Base
1/4-20 x 1/2
Bolts 1/4 Washer 1/4-20 Nuts
USE
2
EACH
•Place the front panel on the assembly. Install
bolt with washer from the bottom into the
base and secure with nuts. Do not tighten.
Front Panel
Side Panel
Bottom Panel
Right Side Panel
Bottom Panel
Front Panel
1/4-20 x 1/2
Bolts 1/4 Washer 1/4-20 Nuts
USE
4
EACH
•Stand the assembly up and bolt the front
panel to the side panels with bolts, washers
and nuts as shown. (2 on each side).
Installation
27" Grill Cart Assembly
•Bolt back brace to side panels by installing
bolt with washer from the outside and
secured with nut on the inside. (2 bolts on
each side).
Back Brace
Side Panel
1/4-20 x 1/2
Bolts 1/4 Washer 1/4-20 Nuts
USE
4
EACH
•Check to be sure all panels and holes in the
bottom right corner of the front panel are
correctly aligned.
•Tighten bolts by holding a 7/16" wrench on
bolt and turning nuts below with another
7/16" wrench.
•Snap grommet into the hole on the outside
of the right side panel.
•Place wheel cap onto axle and tap in place
with a mallot.
•Slide a wheel onto the axle with the flat side
against the cap and the spacer side (the
protruding side) towards the inside of the
cart.
•Slide the axle through the holes in the cart.
•Place second wheel onto the axle, with
spacer side against the cart, and tap wheel
cap with mallet to secure.
USE2
WHEELCAPS
4
Step 5
Install
Back
Brace
Step 6
Check Panel
Alignment,
Tighten
Assembly
Step 7
Install
Wheels
Installation
27" Grill Cart Assembly
CAUTION: Lock front caster on the cart to
prevent movement.
See installation instructions packed with the
grill. Remove packaging, drip tray, burner
grates and parts box.
CAUTION: The grill is extremely heavy. 2
people are required to lift and place the grill
onto the cart.
•Lower the grill onto the cart.
•Check to be sure the grill rests securely and
fits square on the cart.
•Secure the grill to the cart with 2 bolts,
washer and nuts on each side. The bolts may
be accessed from the back of the cart.
1/4-20 x 1/2
Bolts 1/4 Washer 1/4-20 Nuts
USE
4
EACH
The shelf should be installed after the grill
has been secured to the cart.
•Place black plastic bezels onto the ends of
the handle.
•Hold the handle against the shelf and
secure with two 1/4-20 x 3/4" bolts as
shown.
Use 2
Black Bezels
•Hold the assembled shelf against the grill,
aligning screw holes.
•Install bolts and washer through the inside
of the grill, into the top of the shelf and
secure with nuts.
•Drive 2 self-tapping screws with washers into
the lower holes of the shelf and into the
grill.
1/4-20 x 1/2
Bolts
Self-Tapping
Screws
1/4-20 Nuts
Flat Washer
USE
2
EACH
5
USE
2
1/4-20x3/4
Bolts
Self Tapping Screws
Step 8
Mount Grill
to Assembled
Cart
Step 9
Install
Handle
on Shelf
Step 10
Mount Side
Shelf to
Grill
6
Notes
27" Grill Cart Assembly
7
Notes
27" Grill Cart Assembly
To obtain specific information concerning any
Monogram product or service, call GE Answer Center®
consumer information service at 800.626.2000—any
time, day or night.
For Monogram local service in your area, call
1-800-444-1845.
NOTE: Product improvement is a continuing endeavor at General
Electric. Therefore, materials, appearance and specifications are
subject to change without notice.
Monogram.
®
General Electric Company
Louisville, KY 40225
Pub. No. 49-8840
Dwg. No. 164D3333P080
1997 GE Appliances
(N.D. 723) 4/97
10744
Tabla de contenidos
Otros manuales de Parrilla de GE
GE
GE ZGG542LCPSS Manual de usuario
GE
GE JGGN24 Manual de usuario
GE
GE Profile PT970 Manual de usuario
GE
GE ZGG540LCPSS Manual
GE
GE RK959 Manual de usuario
GE
GE Monogram ZGG48L31CSS Manual de usuario
GE
GE Monogram ZGG24L Manual de usuario
GE
GE Monogram ZGG48N31CSS Guía del usuario
GE
GE 106642 Manual de usuario
GE
GE ZGG48L31YSS Manual de usuario
GE
GE 106621 Manual de usuario
GE
GE ZGG420LCPSS Manual de usuario
GE
GE 36 Ceramic Cooktop Manual de usuario
GE
GE 106604 Manual de usuario
GE
GE ZGG300LCPSS Manual de usuario
GE
GE ZGG27120 Manual de usuario
GE
GE Monogram ZGG48N42 Manual de usuario
GE
GE 106811 Manual de usuario
GE
GE 840167200 Manual de usuario
GE
GE 169232 Manual de usuario
