GE UltraMax Manual de usuario

GE Lighting Solutions

1975 Noble Rd. Cleveland, OH 44112

UltraMaxTM Connected LED Driver Installation Guide

GED80MCC/Z2P1500

BEFORE YOU BEGIN: Please read these instructions

completely and carefully

Only Qualified Electricians Should Perform the Installation of this LED Driver

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation. CAN ICES-005 (A) / NMB-005(A).

Note: This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful interference in which case the user will be

required to correct the interference at his own expense.

This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and

Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two

conditions:

1. This device may not cause interference

2. This device must accept any interference, including interference that may cause undesired

operation of the device.

L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR

d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de

licence. L’exploitation est autorisée aux deux conditions suivantes :

1. L’appareil ne doit pas produire de brouillage;

2. L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible

d’en compromettre le fonctionnement.

This equipment (GED80MCC/Z2P1500) contains the limited module with FCC ID PUU80MCCZ2P15

and ISED ID 10798A-80MCCZ2P15. This equipment complies with FCC CFR 47 Part 2 requirements for

radiation exposure for fixed facility or mobile applications that maintain a distance of 20 cm from a

person’s body. This equipment complies with ISED RSS-102 Issue 5 requirements for radiation exposure

limits for an uncontrolled environment that maintain a distance of 20 cm from a person’s body.

This radio transmitter ISED ID 10798A-80MCCZ2P15 has been approved by Innovation, Science and

Economic Development Canada to operate with the antenna types listed below, with the maximum

permissible gain indicated. Antenna types not included in this list that have a gain greater than the

maximum gain indicated for any type listed are strictly prohibited for use with this device.

Any changes or modifications to the equipment not expressly approved by the party responsible for

compliance could void the user's authority to operate the equipment.

Only the following antennas should be used with this limited module and the antenna should only be

installed when the host product is manufactured. (The antenna is not field replaceable.)

•PulseLARSEN W3357 (50Ωimpedance; peak gain over 2400 –2483.5 MHz range is 0.4dBi)

•Walsin RFPCA430618IMAB301 (50Ωimpedance; peak gain over 2400 –2483.5 MHz range is 2.2dBi)

You must follow these codes and safety standards when installing this product:

-National Electric Code (NEC)

-Applicable Federal, Standard and Local Electric Codes

-U.L. safety standards.

Failure to comply with these codes and standards may cause death, serious injury, and property damage.

Before installing this driver:

1. Remove Power from fixture by switching circuit breaker powering the fixture to the off position.

a. Caution: Turning off the fixture’s wall switch maynot remove voltage from fixture.

2. For maximum safety, fixture must be grounded. Make sure fixture is properly grounded

with a green ground wire per National Electrical Code (NEC).

3. Verify that driver is the correct driver for the fixture, input voltage, and application.

During installation:

1. Follow all relevant National Electric Code (NEC), Federal, State and Local Electric Codes as

well as U.L. safety standards.

2. Access and open driver compartment cover.

3. Remove old driver and any extra wires from enclosure.

4. Inspect and replace any damaged or deteriorated cable.

5. Review the wiring diagram on the new driver label (figure below) and identify connections to be made.

6. Install the new driver and make sure the new driver is properly grounded to metal fixture per

National Electrical Code (NEC). Tighten driver mounting screws seating driver firmly against

fixture surface. To insure electrical grounding between driver case and fixture housing

mounting screws with star washers are recommended to break (penetrate) the painted surface

of the driver mounting foot.

7. Install the antenna within the fixture enclosure (away from grounded metal surfaces when

possible). The antenna shall not be cut or have any insulation material removed or tampered

with in any way.

8. Use only U.L. approved wire connectors for all electrical connections. CAUTION: Wire

connectors must be securely fastened and must completely cover exposed wire ends to prevent

shock hazard.

9. Be sure to insulate unused leads INDIVIDUALLY to 600Vrms using U.L. approved wire

connectors.

10. Verify that all installation and safety requirements have been completed and reinstall driver cover.

After driver installation:

11. Restore power at circuit breaker, apply power to the fixture and ensure fixture is operational.

Tabla de contenidos

Otros manuales de Accionamiento de CC de GE

GE AF-600 FP Series Manual de usuario

GE Fuji Electric MICRO-SAVER AF-300 Manual de usuario

GE AF-600 FP BACnet Manual de usuario

GE AF-650 GP Series Manual de usuario

GE AF-600 FP Series Manual de usuario

GE Druck DPI 841 Manual de usuario

GE AF-60 LP Instrucciones de funcionamiento

GE AF-600 FP Metasys Manual de usuario

GE AF-600 FP Series Manual de usuario

GE Ecomagination AF-600 FP Instrucciones de funcionamiento

GE D20A6 Manual de usuario

GE AF-650 GP Series Manual de usuario

GE Fuji Electric MICRO-SAVER AF-300 Manual de usuario

GE AF-650 GP Series Instrucciones de funcionamiento

GE AF-650 GP Series Guía

GE AF-600 FP Series Manual de usuario

GE Fuji Electric FVR-C9S-2UX Series Manual de usuario

GE VAT200 Manual de usuario

GE 6KLP23001X9A1 Manual de usuario

GE AF-650 GP Series Instrucciones de funcionamiento

GE D8R4 Manual de usuario

GE AF-600 FP Series Guía

Manuales populares de Accionamiento de CC de otras marcas

Vincent Associates

Vincent Associates UNIBLITZ ED12DSS Manual de usuario

EKSMA OPTICS

EKSMA OPTICS DQ-100-4 Manual de lista de piezas

Chamberlain Garog

Chamberlain Garog D Series Manual de usuario

Parker

Parker PDS Series Manual de usuario

Festo

Festo DGC G Series Guía de configuración

Binks

Binks QS-5012-1-CE Manual de usuario

Danfoss

Danfoss VLT 2800 Series Hoja de especificaciones

ABB

ABB ACQ580-01 Series Manual de instalación

YASKAWA

YASKAWA CANopen SI-S3 Manual de usuario

Unex

Unex MC-D-250-1000-050W-TW Manual de usuario

Geckodrive

Geckodrive G213V Manual de usuario

ABB

ABB RSYC-01 Manual de usuario

Rockwell Automation

Rockwell Automation PowerFlex 700S Manual del propietario

WEG

WEG DeviceNet CFW500 Manual de usuario

Siemens

Siemens SINAMICS G Hoja de datos

Siemens

Siemens SINAMICS SM150 6SL3815-7NP41-0AA1 Instrucciones de funcionamiento

SOMFY

SOMFY JR RU 30 Manual de usuario

Beckhoff

Beckhoff AX8911 Manual del operador