GE 29391 Manual de usuario
29391
Call Waiting
Caller ID Speakerphone
User’s Guide
We bring good things to life.
2
FCC REGISTRATION INFORMATION
Your GE telephone equipment is registered with the Federal Communications Commission and is in compliance with
parts 15 and 68, FCC Rules and Regulations.
1Notification to the Local Telephone Company
On the bottom of this equipment is a label indicating, among other information, the FCC Registration number and
Ringer Equivalence Number (REN) for the equipment. You must, upon request, provide this information to your
telephone company.
The REN is useful in determining the number of devices you may connect to your telephone line and still have all
of these devices ring when your telephone number is called. In most (but not all) areas, the sum of the RENs of all
devices connected to one line should not exceed 5. To be certain of the number of devices you may connect to your
line as determined by the REN, you should contact your local telephone company.
Notes
• This equipment may not be used on coin service provided by the telephone company.
• Party lines are subject to state tariffs, and therefore, you may not be able to use your own telephone equipment
if you are on a party line. Check with your local telephone company.
• Notice must be given to the telephone company upon permanent disconnection of your telephone from your line.
2Rights of the Telephone Company
Should your equipment cause trouble on your line which may harm the telephone network, the telephone
company shall, where practicable, notify you that temporary discontinuance of service may be required. Where
prior notice is not practicable and the circumstances warrant such action, the telephone company may temporarily
discontinue service immediately. In case of such temporary discontinuance, the telephone company must: (1)
promptly notify you of such temporary discontinuance; (2) afford you the opportunity to correct the situation; and
(3) inform you of your right to bring a complaint to the Commission pursuant to procedures set forth in Subpart E
of Part 68, FCC Rules and Regulations.
The telephone company may make changes in its communications facilities, equipment, operations of procedures
where such action is required in the operation of its business and not inconsistent with FCC Rules and Regulations.
If these changes are expected to affect the use or performance of your telephone equipment, the telephone
company must give you adequate notice, in writing, to allow you to maintain uninterrupted service.
INTERFERENCE INFORMATION
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference; and (2) This device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna (that is, the antenna for radio or television that is “receiving” the
interference).
• Reorient or relocate and increase the separation between the telecommunications equipment and receiving
antenna.
• Connect the telecommunications equipment into an outlet on a circuit different from that to which the receiving
antenna is connected.
If these measures do not eliminate the interference, please consult your dealer or an experienced radio/television
technician for additional suggestions. Also, the Federal Communications Commission has prepared a helpful booklet,
“How To Identify and Resolve Radio/TV Interference Problems.” This booklet is available from the U.S. Government
Printing Office, Washington, D.C. 20402. Please specify stock number 004-000-00345-4 when ordering copies.
HEARING AID COMPATIBILITY
This telephone system meets FCC standards for Hearing Aid Compatibility.
FCC NUMBER IS LOCATED ON THE CABINET BOTTOM
REN NUMBER IS LOCATED ON THE CABINET BOTTOM
3
TABLE OF CONTENTS
WARNING:
TO PREVENT FIRE
OR ELECTRICAL SHOCK HAZARD,
DO NOT EXPOSE THIS PRODUCT
TO RAIN OR MOISTURE.
SEE MARKING ON BOTTOM / BACK OF PRODUCT
CAUTION
RISKOFELECTRICSHOCK
DONOTOPEN
THE EXCLAMATION
POINT WITHIN THE
TRIANGLE IS A
WARNING SIGN
ALERTING YOU OF
IMPORTANT
INSTRUCTIONS
ACCOMPANYING
THE PRODUCT.
THE LIGHTNING
FLASH AND ARROW-
HEAD WITHIN THE
TRIANGLE IS A
WARNING SIGN
ALERTING YOU OF
"DANGEROUS
VOLTAGE" INSIDE
THE PRODUCT.
CAUTION: TO REDUCE THE
RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER
(OR BACK). NO USER-
SERVICEABLE PARTS IN-
SIDE. REFER SERVICING
TO QUALIFIED SERVICE
PERSONNEL.
FCC REGISTRATION INFORMATION .... 2
INTERFERENCE INFORMATION ............ 2
HEARING AID COMPATIBILITY ........... 2
INTRODUCTION ..................................... 4
BEFORE YOU BEGIN .............................. 5
PARTS CHECKLIST ............................. 5
MODULAR JACK REQUIREMENTS ......... 5
INSTALLATION & SETUP ......................... 6
IMPORTANT INSTALLATION INFORMATION 6
INSTALLING THE BATTERIES ................. 6
DESKTOP INSTALLATION ...................... 8
WALL MOUNT INSTALLATION .............. 9
SETTING UPTHE CALLER ID MENU ... 10
SETTING YOUR LOCAL AREA CODE 11
SETTING THE CID DISPLAY
LANGUAGE ............................. 12
SETTING THE DISPLAY CONTRAST .. 13
SETTING THE DIAL MODE ............. 14
EXITING SETUP .......................... 14
SUMMARY SCREEN ......................... 15
CALLER ID WITH CALL WAITING ........ 15
CALLER ID FEATURES .......................... 15
RECEIVING AND STORING CALLS ........ 16
REVIEWING CALL RECORDS ............... 16
DELETING CALL RECORDS ................ 17
DIALING BACK ................................ 17
IFYOU PROGRAMMED YOUR LOCAL
AREA CODE IN THE SETUP MENU .. 18
IFYOU DID NOT PROGRAM YOUR LOCAL
AREA CODE IN THE SETUP MENU .. 19
MESSAGE INDICATORS ......................... 20
USING THE SPEAKERPHONE .................. 21
SPEAKERPHONE LOCATION ................ 21
SPEAKERPHONE USE ....................... 21
TELEPHONE BASICS ............................. 22
RECEIVING APHONE CALL ................ 22
PLACING APHONE CALL .................. 22
SWITCHING BETWEEN SPEAKER AND
HANDSET ............................... 22
TEMPORARY TONE DIALING ........... 23
VOLUME CONTROL .......................... 23
REDIAL .......................................... 23
ONE -TOUCH REDIAL ....................... 24
HOLD ............................................ 24
FLASH ........................................... 25
MEMORY........................................... 26
STORING QUICK DIAL NUMBERS ....... 26
STORING FREQUENTLY CALLED
NUMBERS ...................................... 27
REVIEWING NUMBERS STORED IN
MEMORY ....................................... 27
QUICK DIAL NUMBERS ................. 27
FREQUENTLY CALLED NUMBERS ..... 28
CHANGING ASTORED NUMBER ......... 28
ERASING ASTORED NUMBER ............ 28
STORING APAUSE IN MEMORY ......... 28
DIALING AQUICK DIAL NUMBER ....... 29
DIALING FREQUENTLY CALLED
NUMBERS ...................................... 29
TROUBLESHOOTING TIPS ...................... 30
GENERAL PRODUCT CARE .................... 32
SERVICE ............................................ 32
INDEX ............................................... 33
LIMITED WARRANTY ............................ 35
4
INTRODUCTION
Your Caller ID phone stores and displays specific information, provided by
your local telephone company, to subscribers of Caller ID or similar caller
identification services. You must subscribe to one of these services in
order to use this unit.
Your Caller ID phone enables you to:
• Identify callers before you answer the phone.
• View the time and date of each incoming call.
• Record up to 60 Caller ID messages sequentially.
• Know who called while you were away.
IMPORTANT: In order to use this unit, you must subscribe to either the
standard Name/Number Caller ID Service or Caller ID with Call Waiting
Service. To know who is calling while you are on the phone, you must
subscribe to Caller ID with Call Waiting Service.
5
MODULAR JACK REQUIREMENTS
You need an RJ11 type modular jack, which
is the most common type of phone jack and
might look like the one pictured here. If you
don’t have a modular jack, call your local
phone company to find out how to get one
installed.
Base
Telephone line cord Handset
BEFORE YOU BEGIN
PARTS CHECKLIST
Make sure your package includes the following items:
Coiled cord
1
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
PQ
RS
7
TUV
8
WX
YZ
9
*
PER
0#
SPEAKER
HOLD FLASH
VOLUME
REDIAL
STORE
REVIEWDELETE
DIAL
OPTIONS A B
Short telephone line cord
6
INSTALLATION & SETUP
IMPORTANT INSTALLATION INFORMATION
• Never install telephone wiring during a lightning storm.
• Never touch uninsulated telephone wires or terminals, unless the
telephone line has been disconnected at the network interface.
• Use caution when installing or modifying telephone lines.
INSTALLING THE BATTERIES
Your Caller ID phone uses 4 AA-size alkaline batteries for receiving and
storing Caller ID records and for the numbers you use for memory dialing.
IMPORTANT: You will have approximately 60 seconds to replace the batteries
before the memories stored are lost. Please read the instructions before
replacing the batteries and have the batteries ready to be inserted beforehand.
1. If the line cord is already connected, disconnect it from the base unit.
2. Use a screwdriver to pry up the battery compartment door on the
bottom of the phone.
3. Insert 4 AA-size alkaline batteries as shown on the diagram in the
battery compartment.
4. Snap the battery compartment door back into place.
5. If the line cord was previously connected, re-attach it to the unit and
check your memory locations.
7
Battery
compartment
NOTE: If the low battery icon appears in the display, you need to
replace the batteries. It is important that you replace the batteries as soon as
possible in order to maintain Caller ID operation.
During the replacing of batteries, a backup circuit in the unit will retain your
stored information for up to 60 seconds. Write down any stored information
you do not want erased.
IMPORTANT: If you’re not going to use the telephone for more than 30 days,
remove the batteries because they can leak and damage the unit.
8
2
1
3
DESKTOP INSTALLATION
1. Plug the coiled cord into the handset. Plug the other end into the jack on
the side of the base. Place the handset in the cradle on the base.
2. Plug the line cord into jack on the back of the base. Plug the other end
into a wall jack.
3. Set the RINGER switch on the base to the desired loudness.
• HI = Default, loudest sound.
• LO = Sound will be lower.
• OFF = Telephone will not ring.
9
2
34
1
6
8
WALL MOUNT INSTALLATION
1. Carefully turn the phone over. Detach the wall mount bracket from the
two sets of top grooves by pressing the tabs in. Pull the bracket from
the phone and turn it around so that it looks like the diagram below.
Gently press the bracket into the two sets of bottom grooves until it
snaps into place.
2. Plug the short line cord into the jack on the back of the base.
3. Feed the line cord through the grooves provided so that the base area is
flat and ready to mount on the wall.
4. Connect the other end of the line cord into the wall phone jack.
5. Place the handset in the cradle of the base as soon as possible to hang
up the phone.
6. Plug the coiled cord into the handset. Plug the other end into the jack on
the side of the base.
7. Slip the mounting holes of the base (on bottom of unit) over the wall
plate posts and slide the base down until the phone is firmly in place.
8. Set the RINGER switch on the base to the desired loudness.
• HI = Default, loudest sound.
• LO = Sound will be lower.
• OFF = Telephone will not ring.
7
10
SETTING UPTHE CALLER ID MENU
You should not plug the telephone into the
wall line jack while setting up the Caller ID
menu. An incoming call may invalidate the
change if it was not yet saved. The phone
must display
xx CALLS
before you can
enter the setup menu.
1. Press the OPTIONS button.
OPTIONS
MENU ^ v
appears.
2. At this point you can press either
REVIEW up or down button to scroll
among the 6 menu screens, which are:
•# 1 OPTIONS MENU ^ v
•# 2 LOCAL AREA CODE (default - - -)
•# 3 LANGUAGE (default English)
•# 4 (LCD) CONTRAST (default 3)
•# 5 T/P DIAL MODE (default tone)
•# 6 EXIT OPTIONS
3. You have 10 seconds following any key
press before the phone will
automatically return to the Summary
Screen.
1
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
PQ
RS
7
TUV
8
WX
YZ
9
*
PER
0#
SPEAKER
HOLD FLASH
VOLUME
REDIAL
STORE
REVIEWDELETE
DIAL
OPTIONS A B
10/1912:30
315 - 555 - 1324
SMITH JOHN
REVIEW
buttons
OPTIONS
button
AM
PM
Summary Screen
Otros manuales para 29391
1
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Idiomas:
Otros manuales de Teléfono inalámbrico de GE
GE
GE 27851GE1 Manual de usuario
GE
GE 16197920 Manual de usuario
GE
GE 26939 Manual de usuario
GE
GE 15465 Manual de usuario
GE
GE Edge 25951EE2 Manual de usuario
GE
GE 27901GE1 Manual de usuario
GE
GE 22430 Manual de usuario
GE
GE 26999GE1 Manual de usuario
GE
GE FS21828 Manual de usuario
GE
GE 26730 Manual de usuario
