GE 2-9772 Manual de usuario
2-9772
25-Channel Cordless Telephone
with Caller ID
User’s Guide
We bring good things to life.
2
FCC REGISTRATION INFORMATION
Your GE telephone equipment is registered with the Federal Communications Commission and is in
compliance with parts 15 and 68, FCC Rules and Regulations.
1Notification to the Local Telephone Company
On the bottom of this equipment is a label indicating, among other information, the FCC Registration
number and Ringer Equivalence Number (REN) for the equipment. You must, upon request, provide this
information to your telephone company.
The REN is useful in determining the number of devices you may connect to your telephone line and still
have all of these devices ring when your telephone number is called. In most (but not all) areas, the sum of
the RENs of all devices connected to one line should not exceed 5. To be certain of the number of devices you
may connect to your line as determined by the REN, you should contact your local telephone company.
Notes
• This equipment may not be used on coin service provided by the telephone company.
• Party lines are subject to state tariffs, and therefore, you may not be able to use your own telephone
equipment if you are on a party line. Check with your local telephone company.
• Notice must be given to the telephone company upon permanent disconnection of your telephone from
your line.
2Rights of the Telephone Company
Should your equipment cause trouble on your line which may harm the telephone network, the telephone
company shall, where practicable, notify you that temporary discontinuance of service may be required.
Where prior notice is not practicable and the circumstances warrant such action, the telephone company
may temporarily discontinue service immediately. In case of such temporary discontinuance, the telephone
company must: (1) promptly notify you of such temporary discontinuance; (2) afford you the opportunity to
correct the situation; and (3) inform you of your right to bring a complaint to the Commission pursuant to
procedures set forth in Subpart E of Part 68, FCC Rules and Regulations.
The telephone company may make changes in its communications facilities, equipment, operations of
procedures where such action is required in the operation of its business and not inconsistent with FCC
Rules and Regulations. If these changes are expected to affect the use or performance of your telephone
equipment, the telephone company must give you adequate notice, in writing, to allow you to maintain
uninterrupted service.
HEARING AID COMPATIBILITY
This telephone system meets FCC standsards for Hearing Aid Compatiblility.
FCC NUMBER IS LOCATED ON THE CABINET BOTTOM
REN NUMBER IS LOCATED ON THE CABINET BOTTOM
INTERFERENCE INFORMATION
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference; and (2) This device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
• Reorient or relocate the receiving antenna (that is, the antenna for radio or television that is “receiving” the
interference).
• Reorient or relocate and increase the separation between the telecommunications equipment and
receiving antenna.
• Connect the telecommunications equipment into an outlet on a circuit different from that to which the
receiving antenna is connected.
• Consult the dealer or an experienced radio/TV technician for help.
If these measures do not eliminate the interference, please consult your dealer or an experienced radio/
television technician for additional suggestions. Also, the Federal Communications Commission has
prepared a helpful booklet, “How To Identify and Resolve Radio/TV Interference Problems.” This booklet
is available from the U.S. Government Printing Office, Washington, D.C. 20402. Please specify stock
number 004-000-00345-4 when ordering copies.
3
TABLE OF CONTENTS
WARNING:
TO PREVENT FIRE
OR ELECTRICAL SHOCK HAZARD,
DO NOT EXPOSE THIS PRODUCT
TO RAIN OR MOISTURE.
SEE MARKING ON BOTTOM / BACK OF PRODUCT
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
THE EXCLAMATION
POINT WITHIN THE
TRIANGLE IS A
WARNING SIGN
ALERTING YOU OF
IMPORTANT
INSTRUCTIONS
ACCOMPANYING
THE PRODUCT.
THE LIGHTNING
FLASH AND ARROW-
HEAD WITHIN THE
TRIANGLE IS A
WARNING SIGN
ALERTING YOU OF
"DANGEROUS
VOLTAGE" INSIDE
THE PRODUCT.
CAUTION: TO REDUCE THE
RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER
(OR BACK). NO USER-
SERVICEABLE PARTS IN-
SIDE. REFER SERVICING
TO QUALIFIED SERVICE
PERSONNEL.
FCC REGISTRATION INFORMATION ....... 2
HEARING AID COMPATIBILITY .............. 2
INTERFERENCE INFORMATION ............... 2
INTRODUCTION ..................................... 4
CALLER ID ..................................... 4
CALL WAITING ................................ 4
CALLER ID WITH CALL WAITING .......... 4
VOICE MESSAGING .......................... 4
HANDSET SOUND SIGNALS ................ 5
INSTALLATION AND SETUP ...................... 6
MODULAR JACK REQUIREMENTS ...... 6
DESKTOP INSTALLATION ...................... 7
WALL MOUNT INSTALLATION .............. 8
INSTALLING THE BATTERY ........................ 9
TO REPLACE THE BATTERY .................... 9
TELEPHONE SETUP .............................. 10
SETTING AREA CODE FOR CALLER ID. 10
TELEPHONE OPERATION ....................... 11
RECEIVING ACALL .......................... 11
MAKING ACALL ............................. 11
PHONE LIGHT ............................... 11
REDIAL ....................................... 11
FLASH BUTTON .............................. 11
CHANNEL BUTTON .......................... 11
TEMPORARY TONE .......................... 12
PAGING THE HANDSET ..................... 12
RINGER SWITCH .............................. 12
VOLUME SWITCH ............................ 12
CALLER ID OPERATION ........................ 13
RECEIVING AND STORING CALLS ........ 13
REVIEWING MESSAGES .................... 14
MESSAGE ERRORS .......................... 14
DIALING ACALLER ID NUMBER ......... 15
DELETING CALLER ID RECORDS ......... 15
SPECIAL FEATURES ............................. 16
CALL WAITING WITH CALLER ID ........ 16
STORING NAMES AND NUMBERS ....... 16
INSERTING APAUSE IN THE DIALING
SEQUENCE ................................. 17
CHANGING ASTORED NUMBER...... 18
DIALING ASTORED NUMBER ......... 18
CHAIN DIALING FROM MEMORY ..... 18
REVIEWING AND DELETING STORED
NUMBERS ............................... 19
VERY IMPORTANT PERSON (VIP) FEATURE
19
STORING AVIP NUMBER IN MEMORY19
CALLING AVIP NUMBER ............... 19
REMOVING AVIP NUMBER ............ 20
ERASING ALL VIP NUMBERS .......... 20
VOICE MESSAGING ......................... 21
BATTERY SAFETY PRECAUTIONS ............ 22
GENERAL PRODUCT CARE .................... 22
MESSAGE INDICATORS ......................... 23
TROUBLESHOOTING TIPS ...................... 24
CALLER ID ..................................... 24
CALL WAITING ............................... 24
TELEPHONE .................................... 24
BATTERY ........................................ 26
CALLER ID/CALL WAITING/VOICE
MESSAGING ............................... 27
CAUSES OF POOR RECEPTION ............... 27
SERVICE ............................................ 27
ACCESSORY ORDER FORM ................... 28
INDEX ............................................... 29
LIMITED WARRANTY ............................ 31
4
CALLER ID
This feature allows you to see the number or name and number of
the person calling before you answer the phone.
CALL WAITING
This feature allows you to answer incoming calls while you are
talking on the phone.
CALLER ID WITH CALL WAITING
Also known as Type II Caller ID, this feature allows you to see the
name and number of a call that beep in while you are talking on
the phone with someone else.
VERY IMPORTANT: The Caller ID with Call Waiting feature of this
phone is totally dependent upon your phone company's capabilities.
You may subscribe to one service or the other, or even to both, and
this phone will function properly.
But to take advantage of the Caller ID with Call Waiting feature, you
must call your local phone company and tell the representative that
you have a Caller ID/Call Waiting device that integrates the two
services, regardless of whether or not you already subscribe to one or
both services independently.
The phone companies that do have the ability to integrate Call
Waiting and Caller ID must program your telephone line for the
feature to work.
VOICE MESSAGING
This features, which requires a subscription from the telephone
company, allows callers to leave messages while you are talking
on the phone.
Your GE 2-9772 cordless phone is designed to give you flexibility in use
and high quality performance. You can use this phone with basic tele-
phone service, but it fully functions when equipped with the following
features:
INTRODUCTION
5
#
ABC DEF
JKL
GHI
TONE OPER
MNO
PQRS TUV
F
L
A
S
H
C
H
A
N
N
E
L
M
E
M
O
R
Y
R
E
D
I
A
L
CALL
VIP
ENTER
DELETE
PHONE
WXYZ
123
456
789
0
*
HANDSET SOUND SIGNALS
Signal Meaning
Three long beeps Page signal
A long warbling tone (with ringer on) Signals an incoming call
Four short beeps Out of range warning
LCD (page 13)
DELETE (page 15, 19, 20)
ENTER (page 10, 14, 16, 19, )
PHONE (page 11, 18)
CALL BACK (page 15, 20)
VIP (page 19-20)
DIAL 1+ (page 15, 20)
REDIAL (page 11)
MEMORY (page 16-19)
CHANNEL (page 11)
FLASH (page 11)
TONE (page 12)
number
buttons
VERY IMPORTANT: To fully take advantage of this phone's features, you must
subscribe to Caller ID, Call Waiting and Voice Message services from your
telephone company.
6
INSTALLATION AND SETUP
PAGE / FIND
CHARGE
IN USE
Base Handset
AC power supply
Telephone line cord
Short telephone line cord
MODULAR JACK REQUIREMENTS
You need an RJ11 type modular jack, which is the most
common type of phone jack and might look like the one
pictured here. If you don’t have a modular jack, call your
local phone company to find out how to get one installed.
INSTALLATION NOTE: Some cordless telephones operate at frequencies
that may cause interference to nearby TVs and VCRs. To minimize or prevent
such interference, the base of the cordless telephone should not be placed
near or on top of a TV or VCR. If such interference continues, move the
cordless telephone farther away from the TV or VCR.
Make sure your package includes the items shown here.
NOTE: Use only the Thomson 5-2385 power supply that came with this unit.
Using other adapters may damage the unit.
wall mount bracket
7
DESKTOP INSTALLATION
1. Cradle the phone.
2. Plug the power supply cord into the
base and then into an AC outlet.
3. Raise the base antenna.
4. Allow phone to charge for 12
hours before using the first time.
The CHARGE/IN USE light comes on
indicating that the battery is charging.
5. After charging, connect the telephone
cord to the phone and then to the wall jack.
PAGE / FIND
CHARGE
IN USE
PHONENO.
1
2
3
4
5
6
7
8
9
0
CHARGE/
IN USE
light
3
1
2
4
5
8
Because it is necessary to cradle the
handset for 12 hours prior to connecting
it for use the first time, it is better to
leave the unit on a flat surface during
initial charge before attempting to hang it
on the wall.
1. Cradle the handset.
2. Connect the power supply adapter into
the base and then an AC outlet.
3. Allow phone to charge for 12
hours before using the first time.
The CHARGE/IN USE light comes on
indicating that the battery is charging.
4. After charging, plug the short phone
line cord into the phone jack on the
back of the unit and then to the wall
jack.
5. Attach the wall mount by inserting the
two tabs at the top and then snapping
the tab at the bottom into place.
6. Slip the mounting holes over the wall
plate posts and slide the unit down
firmly into place. (Wall plate not
included.)
WALL MOUNT INSTALLATION
1
2
3
PAGE / FIND
CHARGE
IN USE
PHONENO.
1
2
3
4
5
6
7
8
9
0
CHARGE/
IN USE
light
4
5
9
The handset comes with a brand new, consumer-replaceable nickel
cadmium (NiCad) battery pack. With normal use and recharging, a NiCad
battery pack should last a full year. Use only GE BT-12 replacement battery.
TO REPLACE THE BATTERY:
1. Make sure phone is OFF before you replace battery.
PAGE / FIND
CHARGE
IN USE
PHONE NO.
1
2
3
4
5
6
7
8
9
0
Plug
INSTALLING THE BATTERY
2. Slide open
the battery
compartment
door.
3. Unhook the
strap holding
the battery in
place.
4. Pull out the
battery plug.
5. Remove the
battery pack.
6. Replace and
plug in the
new battery
pack.
Battery Holding Strap
7. Reconnect
the strap to
secure the
battery.
8. Replace the
battery
compart-
ment door.
9. Charge the
battery for
12 hours
before use.
10
SETTING THE AREA CODE FOR CALLER ID
TELEPHONE SETUP
After charging the handset for an initial 12 hours:
1. Set the PULSE/TONE switch to TONE for touch-tone service or PULSE
for rotary service. If you don’t know which type of service you have,
check with the phone company.
2. Plug the telephone line cord into the base and into a modular jack.
3. Turn on the RINGER switch so the handset rings for incoming calls.
1
2
Setting your area code is necessary for proper caller ID operation.
Once you set the code, the phone will automatically remove it from local
calls within your area before it stores the number in memory. This will
enable you to use the Redial feature more efficiently because you will not
have to remove the code each time you call that number.
To set your area code:
1. Make sure the phone is OFF.
2. Press ENTER. The Caller ID display on the handset prompts you to
enter your area code.
3. Enter your 3-digit area code by pressing the appropriate number keys.
The phone emits 2 beeps to confirm it has accepted the area code entry.
4. To change or enter your area code again, follow steps 1-3 above.
PULSE/TONE switch
3
RINGER
switch
VOLUME
RINGER
HI. .LOW
. .
ON OFF
Otros manuales para 2-9772
1
Tabla de contenidos
Otros manuales de Teléfono inalámbrico de GE
GE
GE 28031EE1 Manual de usuario
GE
GE 26936 Manual de usuario
GE
GE 15362520 Manual de usuario
GE
GE 28031 Series Manual de usuario
GE
GE 25836 Manual de usuario
GE
GE 27939 Manual de usuario
GE
GE 21011 Manual de usuario
GE
GE 28128xx3 Manual de usuario
GE
GE 27851FE1 Manual de usuario
GE
GE 55908580 Manual de usuario
GE
GE 27930 Manual de usuario
GE
GE 2-920SST Manual de usuario
GE
GE 28861FE2 Manual de usuario
GE
GE 21015 Manual de usuario
GE
GE 2-7730 Manual de usuario
GE
GE 26920 Series Manual de usuario
GE
GE 28310 Manual de usuario
GE
GE 26980/26981 Manual de usuario
GE
GE 27903 Manual de usuario
GE
GE 28811FE2 Manual de usuario
