GE Profile PGP989SNSS Instrucciones de uso
Dimensions and Installation Information
For answers to your Monogram,® GE Profile™or
GE®appliance questions, visit our website at
ge.com or call GE Answer Center®service,
800.626.2000.
Listed by
Underwriters
Laboratories
PGP989SN
GE Profile™ 30" Downdraft Gas Cooktop
227⁄16ʺ
(229⁄16ʺ SS)
201⁄2ʺ
22ʺ
297⁄8ʺ
(30ʺ SS)
23⁄16ʺ
(21⁄4ʺ SS)
283⁄4ʺ
25
1-7/8"
MIN. Required*
20-5/8
Cut-out Dimensions (in inches)
28-7/8
*U.L. Requirement.
Note: A 5" minimum spacing to adjacent side wall is required
Specification Revised 4/09
230285
*Note: A 5" minimum spacing to adjacent side wall is required
Dimension and installation information are shown in inches.
Wall Installation: Wall installations require 25”
countertop
depth. When cabinet is flush against
the wall, the fan housing can be rotated to the
horizontal position for direct venting through
rear wall. Make a countertop cutout in the
range cabinet according to unit dimensions
and installation type. Duct hole is positioned in
back of cabinet for through-the-wall ducting.
Requires special offset adapter JXRW89.
Peninsula or Island Installation: For peninsula/
islands a minimum 26”
countertop
depth is suggested.
Blower should be in vertical position. Island or
peninsula cabinets may require adjustment in cutout
depth and/or location within the width dimensions.
Duct hole is positioned in bottom of cabinet for island
or peninsula installation.
Slab Installation: For peninsula or island installation
and rear wall ducting, 6” PVC duct or locally
approved piping should be used if installing under
a poured concrete slab.
Installation Information: Before installing, consult
installation instructions, packed with product, for
current dimensional data.
Note: These cooktops are approved for indoor use only.
20
9
4
10-1/2
16
C
L
Cabinet Dimensions (in inches)
227⁄16ʺ
(229⁄16ʺ SS)
201⁄2ʺ
22ʺ
297⁄8ʺ
(30ʺ SS)
23⁄16ʺ
(21⁄4ʺ SS)
283⁄4ʺ
25
1-7/8"
MIN. Required*
20-5/8
Cut-out Dimensions (in inches)
28-7/8
*U.L. Requirement.
Note: A 5" minimum spacing to adjacent side wall is required
Dimensions and Installation Information
For answers to your Monogram,® GE Profile™or
GE®appliance questions, visit our website at
ge.com or call GE Answer Center®service,
800.626.2000. Dimension and installation information are shown in inches.
Listed by
Underwriters
Laboratories
PGP989SN
GE Profile™ 30" Downdraft Gas Cooktop
Specification Revised 4/09
230285
Installing the Ductwork: Use galvanized
or aluminum duct in 6” round or 3-1/4” x
10” size, or combination of both. PVC duct
or locally approved piping should be used
if installing under a poured concrete slab.
Local building code must be followed in
specifying type and schedule of all duct used.
Note: Ductwork must be vented to outside.
Do not vent into a wall, ceiling, crawlspace,
attic or any concealed space. Always use
an appropriate roof or wall cap with damper.
Laundry-type wall caps should never
be used. For maximum efficiency use the
shortest and straightest duct run possible,
with as few fittings as possible.
For satisfactory
performance the duct run
should not exceed 100 feet equivalent length.
Refer to the table of equivalent lengths
(shown in installation instructions) for
various duct configurations.
Rear Wall VentingDownward Venting
Venting Options
Through Cabinet Toe Space Inside Wall to Roof Direct to Outside
Between Floor Joist
9-1/8
10-1/8
18-3/4
6-1/8
PGP989SN
GE Profile™ 30" Downdraft Gas Cooktop
Specification Revised 4/09
230285
Features and Benefits
• Downdraft Exhaust - Powerful exhaust system effectively pulls
smoke and steam out of the kitchen
• Gas On Glass Cooktop - Features a flat one-piece ceramic glass
surface that is sleek and easy-to-clean
• Sealed Cooktop Burners - Eliminate the space between the burners
and the cooktop to help contain spills and boil over liquids, ensuring
easy cleanup
• Continuous Grates - Provide a flat, sturdy surface allowing easy
movement of pans between burners
• Dishwasher-Safe Grates and Knobs - Feature durable construction
for worry-free, effortless cleaning and maintenance
• Deluxe Cast Grates - Constructed from a premium cast iron material
for a long-lasting performance and durability
• Upfront Controls - Controls are placed within easy reach at the front
center of the cooktop
• Model PGP989SNSS - Stainless steel
LITE
LITE
LITE
LITE
PGP989DN_TN_SN
Este manual sirve para los siguientes modelos
1
Otros manuales de Placa de cocina de GE
GE
GE PGP989 Manual de usuario
GE
GE PP989 Instrucciones originales
GE
GE JGP628 Cómo utilizar
GE
GE Monogram ZGU3650 Manual de usuario
GE
GE JP950 Manual de usuario
GE
GE Profile PP989DNBB Manual de usuario
GE
GE CP350 Manual de usuario
GE
GE CGP350SETSS Manual de usuario
GE
GE JP676J Instrucciones de instalación
GE
GE CHP9530 Manual de usuario
GE
GE CGP350SETSS Manual de usuario
GE
GE Profile JGP970BEK Instrucciones de uso
GE
GE JGP975SEKSS Manual
GE
GE 169215 Manual de usuario
GE
GE ZDP30 H Series Cómo utilizar
GE
GE Profile PP932SMSS Manual
GE
GE Profile PP912 Manual de usuario
GE
GE JP383 BR1 Manual de usuario
GE
GE ZGU36L4DD1SS Manual de usuario
GE
GE CGP350SETSS Manual
