GE AZ75H12EACM1 and Instrucciones de funcionamiento

ge.com

Safety Instructions ........... 2

Operati_ Instructions

Controls--Dip Switches ...... 3-5

Controls--Terrain al

Connections .............. 6, 7

On/Off Switch ............... 8

Ventilation Control ........... 8

Care and Cleaning

Air Filters ................... 9

Base Pan ................... 9

Exhaust Coils ................ 9

Installation Instruc_tions

Electrical Supply' ......... ] 1-13

Installing the Zoneline .... ] 4-21

Preparation ................ ] 0

Servicing .................. 22

Troubleshooting Tips ....... 23

Normal Operating Sounds .... 24

Consumer Support

Consumer Support . . .Back Cover

Product Registration ...... 25, 26

*¢\arranty .................. 27

Write the model and serial

numbers here:

Model #

Serial #

Find these numbers on a label

on tile fl'ont case panel.

Heat/Cool and

Heat Pu_@ Modds

7500 Series

TINSEA469JBRZ 49-7534 12-05JR

IMPORTANTSAFETYINFORMATION.

READALLINSTRUCTIONSBEFOREUSING.

WARNING!

Foryour safe_ the information in this manual must be followed to minimize the risk of fire, electric

shock, or to prevent property damage, personal injury, or loss of life.

_\ "_____SAFETYPRECAUTIONS

_y_ • This Zoneline must be properly

installed ira accordance with tile

Installauon Instrucuons before it is

used. See the Installation Instructions

ira tile back of this manual.

Replace immediately all electric service

cords that have become frayed or

otherwise damaged. A damaged power

supply cord must be replaced with a

new power supply cord obtained from

the mamffacturer and not repaired.

Do not use a cord that shows cracks or

abrasion damage along its length or at

either tile plug or connector erad.

•Unplug or disconnect tile Zoneline at

tile fllse box or circuit breaker before

making any repairs.

NOTE."VVestrongly recommend that any

servicing be performed by a qualified

individual.

•All air conditioners contain refligerants,

which under federal law must be

removed prior to product disposal. If

you are getting rid of an old product

with refrigerants, check with the

company handling disposal about wh at

to do.

READANDFOLLOWTHISSAFETYINFORMAtiONCAREFULLY.

SAVETHESEINSTRUCTIONS

Controls-dipswitches. .ecorn

Controls-Dip Switches

The dip sxfitch controls are located behind the

front case I)anel, through, an opening on the

front of the unit.

To access the dip sMtches, remove the front

case panel by removing the filtex, taking out the

ti)ur fl'ont screws, the upper two screws fl'om the

top of the panel and the shipping screws on each

side, if present. (Discard the two side shipping

screws, if present).

zDip

7Switches

Side

• _, shipping

screw

The fi_ctoUsettings will be in the DOWN position.

NOTE:The owner is responsible tot setting

the appropriate dip switches and connecting

temdnals.

TL1(C)(Temp.Limit1-Cool)

TL2(C)(Temp.Limit2-Cool)

TL3(C)(Temp.Limit3-Cool)

ALLI_R(All ElectricHeat)(Heat-pumpmodelsonly) --

FREEZS(FreezeSentinel)

CONSTFAN(ConstantONFan)

TL1(H)(Temp.Limit1-Heat)

TL2(H)(Temp.Limit2-Heat)

TL3(H)(Temp.Limit3-Heat)

[__ u_

DOWN

'Ill, No_.

All Electric Heat (Heat pump models only)

When this switch is enabled (UP), heat pump

operation is locked out, causing the unit to

provide only electric resistance heat. [BE]E]BBB]°_

DOWN

[ BBBBB]°"

DOWN

L ALLI_R(All ElectricHeat)

Controls-dipswitches.

Freeze Sentinel (Requires room air sensor kit-RA VRMS)

_,_]mn this switch is enabled (UP), it turns OFF tile

ti'eeze sentinel protection feature. _._]th tile

switch disabled (DOWN), the freeze sentinel is

acfi\_ted which automatically provides heat

without user intedi_ce. This helps to prevent

I)lumbing damage by turning tile heater and

rims ON at 41 ° F and OFF at 46 ° E

]BBBBBB]°"

DOWN

[B BBBB]

DOWN

L_ FREEZES(FreezeSentinel)

ConstantON Fan

X4qmn this switch is enabled (UP),it allows tile

rims to rtm continuously at high speed, exert if

tile trait is in tile STOP position. [[ BBBBB]D,

DOWN

L CONSTFAN(Constant

ONFan)

OccupancySensor

_,_]/en this switch is enabled (UP), it allows tile

trait to utilize an infl'ared motion sensor and a

door switch tot occui)ancy detection. This timtm'e

allows an energy' management system to be

installed and operated in conjtmction with

tile tmit.

laaaaaal°"

DOWN

lBBB J°"

DOWN

L OCCUPIED

(OccupancySensor)

Duct

Tile duct select flmcfion allows tile indoor

tim to be operated at two wn_iable tim speeds,

depending on the duct length. X,\]mn this switch

is enabled (UP), the unit automaficallv selects

either high or middle tim speed for longer

ductwork applications. When set in the down

position, the trait is automatically operated in

either the middle or low tim speed ti)r shorter

ductwork applications.

[BBBBBB[

DOWN

[BBBBBB[

DOWN

LDUCT

(BlowerFan)

ge.com

Temperature Limiting(Requiresroomair sensorkit-RAVRMS)

Temperature limiting can reduce energy costs of auxiliary controls. The ti_t three switches are

b)' limiting the lowest teini)erature that can be used to select the cooling limits. The next three

set fin" cooling and the highest temperature that switches are used to control the heating limits.

can be set fin" heating, TemI)erature limiting is

controlled by switches 1-6 on the top block

TL1(C)(Temp.Limit1-Cool)

TL2(C)(Temp.Limit2-Cool)

TL3(C)(Temp.Limit3-Cool) [aBBBBBI

DOWN

[aaaaaal

DOWN

TL1(H)(Temp.Limit 1-Heat)

TL2(H)(Temp.Limit2-Heat)

TL3(H)(Temp.Limit3-Heat)

Temperaturelimiting during COOLmode

(all temperatures shown in °F)

UP DOWN Minimum Maximum

NONE 1,2,3 60° 85°

1 2,3 64° 85°

1,2 3 66° 85°

2 1,3 68° 85°

2,3 1 70° 85°

1,2,3 NONE 72° 85°

1,3 2 74° 85°

3 1,2 76° 85°

Temperaturelimiting during HEATmode

(all temperatures shown in °F)

UP DOWN Minimum Maximum

NONE 4,5,6 60° 85°

4 5,6 60° 80°

4, 5 6 60° 78°

5 4,6 60° 76°

5,6 4 60° 74°

4,5,6 NONE 60° 72°

4,6 5 60° 70°

6 4, 5 60° 65°

Controlsmterminalconnections.

Controls-TerminalConnections

Tile texminal connections are located behind tile

front case panel through, an oi)ening, on tile

fl'ont of tile unit.

To access tile teFmillal COllllectiollS, remove tile

fl'ont panel by removing tile filtei, taking out tile

fimr fl'ont screws, tile upper two screws from tile

top ot the panel and the shipping screws on each

side, if present. (Discard the two side shipping

screws, if present).

Insert tile building hook-up wires into tile

bottom ol tile terminals and tighten screws

securely to make tile desired connections.

Route tile wires fl'om tile temfinal connections

through tile unit wire guides and out through

the case wire guide.

NO_.; The owner is responsible tot setting

tile appropriate dip switches and connecting

temfinals.

CAUTION:

hnproper CDC Mring may damage tile Zoneline Routewires

electronics or cause erratic Zoneline operation, through wire

No common busing is permitted. A separate wire guides

pair must be run fl'om each separate controlling

switch to each individual Zoneline,

l H®l®l®i®l®i®l®l®l®l®l

RoomAirSensor

MotionSensor

DoorSensor

CentralDeskControl

o o [_ ommon-Ground

White-Heater

Yellow-Compressor

Black-Reversing Valve

Green-High Speed Fan

Green-Low Speed Fan

Red-24V AC only

Room Air Sensor (Requiresroomair sensorkit- RAVRMS)

"_._q/en connected, tile r(iom air sensor will alh)w

utilization of tile teinperature limiting and freeze

sentinel fb'atures.

NOTE: If GE them_ostat ]LM(147P2 or ILM(163P2

is used with tile unit, tile room sensor kit is not

needed, since temperature limiting and freeze

sentinel features are incoq)orated in tile

them_ostats.

o_ _o

_:'* S= o

L Room Air

Sensor

ge.com

Motion Sensor (Obtainedlocally)

Tile Occupancy Sensor dip switch nmst be ill

tile up position to use this teature.

\_]/en connected, the wall mounted motion

sensor will demct motion in the room and

autolnaficallv cycle tile unit between nomml

operation and energy inanagelnent operation.

Tile door and Inofion sensoI_ work together

to automatically cycle the unit between nomml

operation and energy inanagelnent operation.

I I o o

L_ Motion Sensor

Door Sensor (Obtainedlocally)

The Occupancy Sensor dip switch must be in the

up position to use this teatuI'e.

_]/en connected, tile door sensor will detect

when tile door ill tile room is opened or closed.

This ti_atuI'e n/ust be used in coqjunction with

tile i/lotion sensoI:

The door and i/lotion sensoi3 work together

to auton/aticallv cycle the unit between mmnal

and enei'_ry,, i//anagei//ent, ol)ei'ations.

CentralDesk Control

\4lien connected, tile unit lock-out is released

and it can be turned ON or OFF with a switch

located at the (:entral Desk (;ontrol. A separate

wire pair must be run fl'om each separate

controlling switch to each individual Zoneline.

Remote Thermostat

The unit will be controlled by a rein ote

themlostat.

IMPORTAN7

Tile Zoneline themlostat cmmections

provide 24V AC only.

If using a digiml/elecmmic wall themlostat,

you inust set it to tile 24V AC setting. See tile

Installation Instructions tor tile wall themlostat.

ACAUTION:

Dalnage to a wall themlostat or to tile

Zoneline electronics can result fl'Oln ilnproper

connections. Exercise extra attention when

connecting blue and black wires. No line

voltage connections should be inade to anv

drcuit ill tile d/elmostat. Isolate all wires ill

building fl'oln lille voltage.

Central Desk Control

cc_ -

Red-24V AC0nly

Green-LowSpeedFan

Green-HighSpeedFan

Black-ReversingValve

Yellow-Compressor

White-Heater

Common-Ground

OtherfeaturesofyourZoneline.

On/Off Switch

The unit on/oH' switch is located on the ti'ont oI

the Zoneline.

Toturn the unit on, press the top oI the switch in.

Toturn the unit of[, press the botton_ oI the

switch in. ON/OFF

switch

Ventilation Control

The ventilation control lever is located on the

left side ot the Zoneline unit, behind the ti'ont

case panel.

To access the ventilation control leve_; remove

the front panel by removing the filte_; taking out

the ti)m" ti'ont screws, the ul)per two screws ti'om

the top of the panel and the shipi)ing screws on

each side, if present. (Discard the two side

shipi)ing screws, if present).

_._]_en the lever is in the CLOSEposition, only the

air inside the room is circulated and filtered.

\._]]en the lever is in the OPEIVposition, some

outdoor air will be drawn into the room. This

will reduce the heating or cooling eflidencv.

Toclose the vent, push the vent lever handle

down, pull it fin'ward and lock it up in place.

Toopen the vent, push the vent lever handle down,

push it back and lock it up in place.

Ventcontrol

(pushleverdown

andpullforward

orbackto

operate)

Energy Tip: Kee I) the vent control in the

CLOSEposition. The room air will be filtered

and drculated.

AboutHeat Pumps(onsomemodels)

Heat pumps can reduce operating costs by

exchanging heat ti'om the outside air----even

when the outside temperature is below

fl'eezing-- and releasing that heat ind{){n_.

To get the best economic benefit ti'om yore" heat

I)ump, don't change the room themmstnt setting

very often. Raising the heat setting 2-3 degrees

will cause the Zoneline to use its electric heating

elements in order to reach the new temperature

setting quickly.

There is a three minute minimum compressor

mn time at any setting to prevent short cycling.

The indoor tim motor stnrts befin'e the

compressor and stops after the compressor

cycles off.

The electric heating elements use much

more electricity than heat i)umps and cost

II/OI'e to operate.

Careand cleaning, gecem

Turnthe Zoneline offand disconnectthepower supplybeforecleaning.

Indoor/Outdoor Coils

The exhaust coils on the Zoneline should be

checked regularly: If they are clogged with dirt or

soot, they may be protessionally steam cleaned by

w)ur (;E service center; You will need to remove

the refit fl'om the case to inspect the coils

because the dirt build-u I) occm_ on the

exhaust side.

-- Outdoor coils

Have the ceils cleaned regularl,_

Drain

Clean the drain system regularly to

prevent clogging.

Base Pan

In some installations, dirt or other debris may be

blown into the refit fl'om the outside and settle in

the base pan (the bottom of the refit).

In some areas of the United States, a "gelqike"

subst;mce may be present in the base pan.

Check it periodically and clean, if necessa_w:

Air Filters

Tomaintain optimum performance, change the filter at least every30 days.

The most important thing )'ou can do to Toremove

maintain the Zoneline is to change the filter at and replace

least eve_w 30 days. Dirty filte_ reduce cooling, the filter:

heating and air flow.

Changing the filter will: Decrease cost of operation,

save energai, prevent clogged heat exchanger

coils and reduce the risk ot premature

component tailm'e.

CAUTION: Oonotoperatethe

Zoneline wi_out the filter in place. If a filter

becomes tornor damaged, It should be replaced

immediately.

Operating without the filter in place or with a

damaged filter will allow dirt and dust to reach

the indoor coil and reduce the cooling, heating,

airflow and efficiency of the unit.

Replacement filtex_ should be imrchased fl'om

your local retailer where air conditioner and

lilI'IlaCe accessolJes are sold.

Filter size required is 20" x 20" x 1".

Filter

Remove filter

Unit-mounted filter

Filter

Returnairgrille Access-panelwith

returnair grille 9

Installation

Instructions Zoneline Air

Conditioners

Iouestions?Visit our Website at: ge.com or call800.GE.CARES(800.432.2737).

BEFORE YOU BEGIN

Read these instructions completely and carefully.

• IMPORTANT -S.,ethese

instructions fin" local inspector's use.

• IMPORTANT - Obse,,e.ll

governing codes and ordinances.

•Note to Installer -Be sure to leave these

instructions with the owner.

• Note to Owner - Kee I) these instructions tot

fl]ture reference.

• Proper installation is the responsibility of the

installer.

"Product tailure due to improper installation is not

covered under the X_hrrantv.

TOOLS YOU WILL NEED

Phillips screwdriver

Saw

Adjustable wrench

Hammer

Tapemeasure

IMPORTANT ELECTRICAL

SAFETY-READ CAREFULLY

CAUTION:

• All electrical cmmections and wiring MUST be

installed by a qualified electrician.

• Follow the National Electrical Code (NEC) and/or

local codes and ordinances.

•For personal safety, this Zoneline unit and case

must be properly grounded.

•Protective devices (fuses or circuit breakers)

acceptable for Zoneline installations axe specified

on the nameplate of each unit.

• Do not use ml extension cord with this unit.

• Aluminum building wiring may present special

problems--consult aqualified electrician.

• When the unit is not running there is still voltage to

the electrical controls.

Discmmect the power to the unit before

servicing by:

1. Removing the power cord (if it has one) from

the wall receptacle.

2. Removing the brmlch circuit fuses or turning

the circuit breakers off at the pmlel.

^AUkWARNING: Bef,,,ebe_im,i.,_the

installation, switch power off at the service panel

and lock the area to prevent power from being

switched on accidentally. When the area cannot

be locked, secm'elv tasten a prominent warning

device, such as a tag, to the selwice panel.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Acondicionador de aire de GE

GE AEL14 Series Instrucciones de funcionamiento

GE AEE23DP Instrucciones de montaje

GE AHH24DW Manual de usuario

GE UUC112WC Series Manual de usuario

GE AJCH08ACC Instrucciones de funcionamiento

GE APSA13 Instrucciones de funcionamiento

GE APCA10NXMGN1 Instrucciones de funcionamiento

GE Carry-Cool ATA04 Instrucciones de instalación

GE AJCM08ACE Instrucciones de funcionamiento

GE AEH12AP Instrucciones de funcionamiento

GE AJCQ10ACD Series Instrucciones de montaje

GE AKM25DN Instrucciones de uso

GE ACV24D Manual de capacitación

GE AEM12AP Instrucciones de funcionamiento

GE AEW10AM Instrucciones de funcionamiento

GE AFH12 Instrucciones de instalación

GE AHM18 Series Instrucciones de funcionamiento

GE AHM06 Manual de usuario

GE ASF05 Instrucciones de funcionamiento

GE AEQ05LP Instrucciones de funcionamiento

GE AER05 Instrucciones de funcionamiento

GE AJCM08ACF Series Instrucciones de funcionamiento

GE AHLE06CA Manual de usuario

GE AEH14 Instrucciones de funcionamiento

Manuales populares de Acondicionador de aire de otras marcas

Spheros

Spheros CC 355 Manual de usuario

Bosch

Bosch Climate 5000 SCI 24 CAS/ OU- OUE Manual de usuario

Panasonic

Panasonic CS-E12HKEW Manual de usuario

nedis

nedis ACMB1WT7 Manual de usuario

Samsung

Samsung AR KV Series Guía

Daikin

Daikin FCFV50A Manual de usuario

Fujitsu

Fujitsu Inverter ASBA30JFC Manual de usuario

Toshiba

Toshiba RAS-M10SMUV-E Manual de usuario

Daikin

Daikin FXLQ20MAVE Manual de usuario

Hitachi

Hitachi RAS-E24CAK Manual de usuario

CIAT

CIAT Magister 2 Series Guía

Bestron

Bestron AAC6000 Manual de usuario

Hisense

Hisense 7K Manual técnico

Frigidaire

Frigidaire FFRE0533S1E0 Manual de usuario

Samsung

Samsung AS09HM3N Manual de usuario

Frigidaire

Frigidaire CRA073PU11 Manual del propietario

Soleus Air

Soleus Air GB-PAC-08E4 Manual de usuario

McQuay

McQuay MCK020A Manual de usuario