Gate House G27D01 Manual de usuario
ITEM #0399129/0399128
ELECTRONIC KEYPAD DEADBOLT
MODEL #G27D01/G2X2D01
Questions?
Call customer service at 1-877-4GATEHS, 8:00 a.m. - 8:00 p.m., EST, Monday - Friday.
ATTACH YOUR RECEIPT HERE
Serial Number ____________________ Purchase Date _____________________
1 2
4
5
7 8
0
9
3
C
6
Español p. XXEspañol p. 37
TABLE OF CONTENTS
SAFETY INFORMATION........................................................................................
PACKAGE CONTENTS..........................................................................................
PREPARATION.......................................................................................................
INSTALLATION.......................................................................................................
OVERVIEW OF FUNCTIONS..................................................................................
CODES INFORMATION..........................................................................................
SETTING MODE
1. AUTOMATIC - BOLT DIRECTION DETERMINATION......................................
2. CHANGE PRESET OR CURRENT PROGRAMMING CODE...........................
3. ADD NEW USER CODE....................................................................................
4. DELETE INDIVIDUAL EXISTING USER CODE................................................
5. DELETE ALL EXISTING USER CODES AT ONCE..........................................
6. RESTORE FACTORY SETTING ......................................................................
7. AUTO LOCKING FUNCTION ...........................................................................
OPERATION MODE
1. LOCK OPERATION ..........................................................................................
2. SECURITY MODE.............................................................................................
TROUBLESHOOTING ...........................................................................................
INFORMATION ......................................................................................................
WARRANTY ..........................................................................................................
FEDERAL COMMUNICATIONS COMMISSION STATEMENT..............................
TEMPLATE .............................................................................................................
01
02
03-08
09-17
18
19
20
21
22
23
24
25
26
27
28
29-32
33
34
35
36
01
!SAFETY INFORMATION
1. Do not attempt to disassemble any internal components of this lockset as this WILL
void the limited warranty.
2. Do not drop or hit/strike the lockset as excessive shock may result in permanent damage.
3. Do not use sharp objects to press key buttons.
4. It is strongly recommended that you always create a written backup of the programming
code and individual user codes. Please use the last page of this booklet as your reference.
5. For your security, please remember to change this lockset's factory default programming
code to a PERSONAL programing code prior to normal day-to-day use of this product.
6. It is strongly recommended that you use only ALKALINE BATTERIES to operate this
product.
!WARNING
1. To prevent damage to the finish, Do NOT use any abrasives, sharp objects or harsh
chemical products containing alcohol, petroleum solvents, acids or acetone to clean
this lockset.
2. Do not let any water or liquid into lockset during installation process.
CARE AND MAINTENANCE
The following care instructions should be followed to ensure a long-lasting finish:
1. Prior to painting your door, remove locks or do not install locks.
2. Periodically clean with mild soap and a soft cloth only.
02
PART DESCRIPTION QUANTITY
A Exterior Assembly 1
B Power Strip 1
C Tailpiece 1
D Mounting Plate 1
E
2-1/8 in. (54 mm) Mounting Bolt 2
F Interior Assembly 1
G
13/16 in. (20.5 mm) Screw
1
H
5/16 in. (8 mm) Screw
2
I Interior Cover 1
J Latch 1
K
3/4 in. (19 mm) Wood Screw
4
L Strike Plate 1
M
3 in. (76 mm) Wood Scre
w 2
N Reinforced Strike Plate 1
O Dust Box 1
PART DESCRIPTION QUANTITY
G
J
K
M
L
N
O
D
F
H
BA
C
IE
PACKAGE CONTENTS
03
PREPARATION
Before beginning installation of product, make sure all parts are present.
Compare parts with package contents list and hardware contents list.
If any part is missing or damaged, do not attempt to assemble, install or operate the product.
ESTIMATED ASSEMBLY TIME: 40 - 60 MINUTES
TOOLS NEEDED FOR NEW INSTALLATION (NOT INCLUDED):
• Pencil
• Chisel
• Tape Measure
• Hammer
• Phillips Screwdriver
• 1 in. (25 mm) and1/8 in. (3 mm) Drill Bits
• 2-1/8 in. (54 mm) Hole Boring Bit
• Power Drill
• 2 in. (51 mm) 6d Common Nail
• Flathead Screwdriver
04
PREPARATION
NOTE: If replacing an existing lock or installing in a pre-drilled door, please start from page 08.
For new installation, which requires the door to be drilled, please start from page 04.
or
Mark door edge approximately
3 in. (76 mm) to 6 in. (152 mm)
above the entry knob or lever.
Centerline
Template
1. MARK DOOR WITH TEMPLATE (REFER TO PAGE 36, 37)
a. Use TEMPLATE to mark centerline on door for keypad deadbolt about
3 in. (76 mm) to 6 in. (152 mm) above the existing knob or lever.
b. Face door swings to align and fold template as shown.
05
PREPARATION
2. MARK AND DRILL PILOT HOLES
Select backset: 2-3/8 in. (60 mm) or 2-3/4 in. (70 mm). Refer to page 09 for latch
backset adjustment if needed. Mark and drill 1/8 in. (3 mm) pilot holes as shown.
2-1/8 in. (54 mm)
1 in. (25 mm)
Backset Drill 1/8 in. (3 mm) pilot hole.Drill 1/8 in. (3 mm) pilot hole.
Centerline
06
PREPARATION
2-1/8 in. (54 mm)
3-1. DRILL HOLES
a. Drill a 2-1/8 in. (54 mm) hole on the door face from both sides to avoid wood splitting.
b. Use a 2 in. (51 mm) 6d common nail and press it from inside the 2-1/8 in. (54 mm)
hole through the pilot hole to mark centerlines on jamb exactly opposite center of
deadbolt latch hole.
07
PREPARATION
3-2. DRILL HOLES
c. Drill a 1 in. (25 mm) hole in the door edge for the latch.
d. Use faceplate of the latch (J) as a pattern for mortise and pilot holes.
Chisel 1/8 in. (3 mm) deep. Faceplate should fit flush.
1 in. (25 mm)
Faceplate
Outline
Chisel 1/8 in.
(3 mm) deep.
J
08
PREPARATION
4. PREPARE DOOR JAMB AND INSTALL STRIKE PLATE
Mark outline for dust box (O) and then drill a hole 1-3/16 in. (30 mm) deep by 1-9/16 in (40 mm)
tall by 1 in. (25 mm) wide to allow for installation of dust box (O). Chisel a 5/32 in. (4 mm) deep
outline for the strike plate (L) on the door jamb. Install the dust box (O) and the reinforced strike
place (N) with the 3 in. (76 mm) wood screws (M). Install the strike place (L) with the
3/4 in. (19 mm) wood screws (K).
NOTE: The dust box (O) and reinforced strike plate (N) are optional. Install both for
maximum security.
Door jamb hole dimension:
1-3/16 in. (30 mm)
1-9/16 in. (40 mm)
1 in. (25 mm)
Strike dimension:
5/32 in. (4 mm)
2-3/4 in (70 mm)
1-1/8 in. (28 mm)
O
N
L
K
M
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Idiomas:
Otros manuales de Cerrar de Gate House
