Gasmate RB2SL Manual de usuario
CAST IRON RING BURNERS
Model No. RB2SL, RB3SL, RB4SL
•Includes LCC27 Safe Lok regulator & hose
•Ideal for camping, use only on the solid ground
that is non-combustible
•Suitable for cooking at home where larger pots
and a higher heat output is required – convenient
for cooking sauces, crabs, lobster or any shell sh
•Made from high quality cast iron with brass controls
•Outlet: ¼” BSP thread
•Propane use only
•Gas certied to Australian Standards
RB2SL
RB3SL
RB4SL
NOTE: ONLY USE ON A NON-COMBUSTIBLE SURFACE
USE ONLY ON THE SOLID GROUND
Important: Retain these instructions for future use.
Gasmate® is a registered trademark of
Sitro Group Australia Pty Ltd www.gasmate.com.au
Aber Living, N.Z. www.gasmate.co.nz 04217 06/22
LCC27 REGULATOR
SUPPLIED
This LCC27 Regulator can only be used
with the new safer industry standard
LCC27 Gas Cylinder Connection.
2
GENERAL INFORMATION
IMPORTANT
• Outdoor use only.
• Read these instructions for use carefully.
Familiarise yourself with the appliance before
connecting it to its gas container. Keep these
instructions for future reference.
• Failure to comply with these instructions could result
in a fire or explosion which could cause serious bodily
injury, death or property damage.
• CAUTION: Accessible parts may be very hot. Keep
young children away.
• DO NOT modify this appliance.
• DO NOT move this appliance during use.
• Turn off the gas supply at the gas cylinder after use.
• Parts sealed by the manufacturer or their agent must
not be manipulated by the user.
• This appliance is only to be used outdoors.
• Never operate this appliance without a regulator.
• Do not test for gas leaks with an open flame.
• If this information is not followed exactly a fire
causing death or serious injury may occur.
• Do not store a spare gas cylinder under or near
this appliance. Never fill the cylinder beyond 80% full.
This appliance is only to be used and stored outdoors.
• If there is a leak on your appliance (smell of gas),
immediately attempt to turn off the cylinder valve.
Remove the appliance to a well ventilated location
away from any ignition source. Only check for leaks
outdoors using soapy water. DO NOT try to detect
leaks using a flame.
• Never connect an unregulated gas cylinder
to your appliance.
NOTE: ONLY USE ON A NON-COMBUSTIBLE SURFACE
ONLY USE ON THE SOLID GROUND
Gas Installation Codes
• Appliance must be used in accordance with the
installation requirements of your gas supply authority,
or the appropriate installation code issued by Standards
Australia AS 5601.
• Appliances for use with bottled gas are labelled
‘propane gas’.
• Only use on a non-combustible surface.
• Only use on the solid ground.
• USE OUTDOORS ONLY
Clearances
Minimum Clearances from combustible materials must be:
Cylinder – 500mm. Wall – 500mm. Above – 1200mm.
Below – never use on a flammable surface. Only use on
a non-combustible surface.
Hose & Regulator Safety
The regulator and hose assembly supplied with
the appliance are suitable for propane gas only.
The pressure regulator and hose assembly supplied
with the appliance must be used. Replacement pressure
regulators and hose assemblies must be those specified
by the appliance manufacturer.
The supplied LCC27 regulator and hose will only suit
the safe LCC27 gas cylinder connection. Only use
the hose assembly supplied with this appliance for direct
connection to the cylinder
“DO NOT USE ADAPTORS”.
Check the regulator “O” Ring periodically for wear
or damage and replace if required.
When connecting the hose and regulator assembly
to the gas cylinder, take care to avoid unnecessary
twisting or kinking of the flexible hose. Maximum hose
length is 1 metre.
After the assembly has been secured, turn on the gas
and check for leaks by brushing a soap and water solution
overall connections.
DO NOT USE this appliance if it is leaking, damaged
or does not operate properly.
If you are unable to correct the leak by tightening the
connections, turn off the gas and contact the supplier
immediately.
Always ensure the appliance is kept away from flammable
materials and the gas cylinder clear of any heat source.
When changing over from an empty gas cylinder to a full one
make sure this procedure is carried out in a well ventilated
location, preferably outside, away from people and away
from any sources of ignition; such as naked flames, pilot
flames, electric heaters/equipment.
Specifications
Appliance specifications can be found on the data label
attached to the appliance body.
Gas Cylinder Use & Safety
This is a low pressure appliance and must only be
used with the hose and regulator supplied. This appliance
shall only be used with propane gas cylinders certified
to AS 2469. It may be hazardous to attempt to fit other types
of gas containers.
ONLY USE IN WELL-VENTILATED AREAS CARBON
MONOXIDE HAZARD- USING THIS APPLIANCE IN AN
ENCLOSED SPACE MAY CAUSE DEATH. DO NOT USE
IN CARAVANS, TENTS, MARINE CRAFT, CARS, MOBILE
HOMES OR SIMILAR LOCATIONS.
The gas cylinder should be filled by a reputable gas supplier
and visually inspected and re-qualified at each filling.
Always keep cylinder in an upright position.
Always close the cylinder valve when the appliance
is not in use.
Do not subject gas cylinder to excessive heat.
2 3
Product Details
Model Number RB2SL
Gas Type Propane
Inj. Size (mm) Ø 0.63 Ø 1.05
Gas Cons. (MJ/h) 5.5 13
Gas Pressure 2.75kPa
Overall Size 425 x 200 x 70mm
Weight 3.4kg
Model Number RB3SL
Gas Type Propane
Inj. Size (mm) Ø 0.50 Ø 0.80 Ø 1.14
Gas Cons. (MJ/h) 3.0 8.5 16.8
Gas Pressure 2.75kPa
Overall Size 465 x 239 x 90mm
Weight 5.9kg
Model Number RB4SL
Gas Type Propane
Inj. Size (mm) Ø 0.50 Ø 0.80 Ø 1.14 Ø 1.5
Gas Cons. (MJ/h) 3.0 8.5 15.5 27
Gas Pressure 2.75kPa
Overall Size 640 x 355 x 112mm
Weight 13.1kg
FOR YOUR SAFETY
• Do not store or use petrol or other flammable liquids
in the vicinity of this or any other appliance.
• Do not store empty or full spare gas cylinders under
or near this or any other appliance.
• Keep the gas hose away from hot surfaces and
protect from dripping grease. Avoid unnecessary
twisting of hose. Visually inspect the hose prior
to each use for cracks, excessive wear or other
damage. Replace the hose if necessary.
• Never test for gas leaks with a lit match or open flame.
• Never lean over cooking surface when lighting.
• Never alter or modify the regulator or gas supply
assembly.
• This appliance must not be used indoors.
• The supplied LCC27 regulator and hose will only
suit the safe LCC27 gas cylinder connection.
• Only use in well ventilated areas.
• Carbon monoxide hazard – Using this appliance
in an enclosed space may cause death. Do not use
in caravans, tents, marine craft, cars, mobile homes
or similar locations.
• This appliance shall only be used in an above ground
open-air situation with natural ventilation, without
stagnant areas, where gas leakage and products
of combustion are rapidly dispersed by wind and
natural convection.
• Ensure the appliance is set up on a level
and stable surface.
• Do not move the appliance while in use or when hot.
NOTE: ONLY USE ON A NON-COMBUSTIBLE SURFACE
ONLY USE ON SOLID GROUND
Never Store your Gas Cylinder Indoors
If you store your appliance indoors, ALWAYS disconnect
the gas cylinder first and store the cylinder safely outside.
Cylinders must be stored outdoors in a well ventilated
area out of reach of children, and must not be stored in
a building, garage or any other enclosed area.
Gas connection is 1/4” BSP
Location of your Appliance
Only use on a non-combustible surface. DO NOT use your
appliance in garages, porches, sheds, breezeways, or other
enclosed areas. Your appliance is to be used OUTDOORS
ONLY. USE ONLY ON THE SOLID GROUND. The appliance
is not intended to be installed in or on recreational vehicles,
caravans and/or boats and should not be placed on
any surface that will burn. Do not obstruct the flow of
combustion and ventilation air around the appliance.
Protect Children
Always ensure that no sporting or physical activities are
carried out in close proximity to the appliance during use
and while still hot.
Keep children away from appliance during use and until
appliance has cooled after you have finished. Do not allow
children to operate appliance.
Tools You Will Need
Adjustable spanner, Phillips screwdriver.
Check Appliance for any Damage
Inspect appliance parts as you proceed. Contact your
supplier for assistance regarding replacement of any
damaged or missing parts. Do not assemble or operate
a appliance that appears damaged. Appliance for use with
gas cylinders are labelled ‘propane gas’. Check labelling
at the gas connection on your appliance.
GAS VALVE ASSEMBLY
Gas valve in off position
Gas inlet
Primary air disk
BURNER ASSEMBLY
Venturi tube
3
2
1
4
4
ASSEMBLY
Note: Remove any transit protection material before using
the burner.
1. Slide gas valve assembly into the burner assembly
and secure with the two screws provided.
2. Attach the supplied hose and regulator to the gas inlet.
1. LCC27 regulator and hose assembly
2. Gas valve
• RB2SL – screws from underside
• RB3SL – screws from underside
• RB4SL – screws from underside
3. Burner
• RB2SL - 2 rings
• RB3SL - 3 rings
• RB4SL - 4 rings
4. Trivets – to stand cooking pot on
Note: Remove any transit protection material
before using the burner.
RING BURNER COMPONENTS (Image as guide only)
Wall
Ground - Non combustible surface and/or material.
USE ONLY ON THE SOLID GROUND
min 500mm min 500mmmin 1200mm
4 5
Connecting & Disconnecting to Gas Source
Familiarise yourself with the general information and safety
guidelines located at the front of this manual.
Check
1. Gas cylinder is filled. A sloshing sound will be heard
when shaken.
2. The gas valve is in the ‘OFF’ position.
Connecting
1. Ensure cylinder and gas valve is in its full off position.
2. Check for any damage to either the cylinder connection
or the hose. NEVER attempt to use damaged
equipment.
3. When connecting the hose to the cylinder tighten
the nut to a positive stop by hand or spanner.
NOTE: The supplied LCC27 regulator and hose will
only suit the safe LCC27 gas cylinder connection.
4. Open cylinder valve fully. If a leak can be heard at either
end of the hose turn cylinder off and tighten joint.
Wait 5 minutes before re-testing and use a soapy
water solution to check the joint. If bubbles appear
the connection will need to be re-tightened.
General Positioning
1. Never place or position the ring burner on combustible
material. Only use on a non-combustible surface.
2. Ensure the gas hose is straight and not knotted.
IMPORTANT
Before connecting and disconnecting appliance
to gas source, make sure burner controls are in
‘OFF’ position.
CAUTION: When the appliance is not in use,
the gas must be turned off at the cylinder.
Check that the seals between the appliance
and the gas cylinder are in place and in good
condition before connecting the gas cylinder.
Do not use this appliance if it has damaged
or worn seals.
• Beware of spiders and wasps. Burner tube
should be inspected and cleaned periodically.
• This appliance must only be serviced
by an authorised person.
NOTE: ONLY USE ON A NON-COMBUSTIBLE
SURFACE ONLY USE ON SOLID GROUND
NOTE: THE SUPPLIED LCC27 REGULATOR
AND HOSE WILL ONLY SUIT THE SAFE LCC27
GAS CYLINDER CONNECTION.
As with all appliances, proper care and maintenance will
keep them in top operating condition and prolong their life.
Your new gas appliance is no exception. By following these
cleaning procedures on a timely basis, your appliance will
be kept clean and working properly with minimum effort.
Spiders and small insects occasionally spin webs
or make nests in the burner tubes during warehousing
and transit. These webs can lead to a gas flow obstruction
which could result in a fire in and around the burner tubes.
Cleaning with a soft brush before use and at least every
six months is recommended.
This type of fire is known as ‘FLASH-BACK’ and can cause
serious damage to your appliance and create an unsafe
operating condition for the user. Although an obstructed
burner tube is not the only cause of ‘FLASH-BACK’ it is
the most common cause and frequent inspection and
cleaning of the burner tubes is necessary.
Flash-Back
If fire occurs in and around the burner, immediately turn off
gas at its source and turn the burner control to ‘OFF’, wait
until the appliance has cooled, then clean the burner tubes
and burner ports.
Cleaning
After cooking, turn burner gas cylinder valve and burner
valve to ‘OFF’. Let the burner cool before attempting
to clean and store. After use brush excess dust, dirt
and debris from the burner surface. Ensure all the burner
ports are clean and open before storing and re-using.
Ensure the bottoms of all cooking pots / pans are cleaned
of any dirt or discolouration after use.
GENERAL ASSEMBLY CARE & MAINTENANCE
RB2
4
1
Inner # 1
Outer # 4
RB3
4
2
1Outer # 4
Inner # 1
1st Middle # 2
RB4
4
2
1
3
Outer # 4
1st Middle # 2
Inner # 1
2nd Middle # 3
6
AERATION
To ensure the flame is clean and blue, that is NO yellow
tip to flame or sooting, adjust the primary air disk.
The primary air disk can be adjusted clockwise/counter
clockwise by hand.
The ideal positioning of the aeration disk when measured
from the venturi tube is:
RB2SL - INNER # 1 – 2mm open
- OUTER # 4 – 3mm open
RB3SL - INNER # 1 – 7mm open
- 1st MIDDLE# 2 – 7mm open
- OUTER # 4 – 3mm open
RB4SL - ALL BURNER RINGS 3mm open
Burner Operation & Ignition System Check
1. Turn inner gas valve on.
2. Open gas valve and light immediately with long
BBQ match following sequence in Step 3.
3. Light the burners in order:
Without pot:
RB2SL RB3SL RB4SL
Inner # 1 Inner # 1 Inner # 1
Outer # 4 1st Middle # 2 1st Middle # 2
Outer # 4 2nd Middle # 3
Outer # 4
All of these will need to be lit using a long BBQ match.
With pot:
RB2SL RB3SL RB4SL
Outer # 4 Outer # 4 Outer # 4
Inner # 1 1st Middle # 2 2nd Middle # 3
Inner # 1 1st Middle # 2
Inner # 1
The outer ring #4 will need to be lit using a long BBQ
match, all other rings will cross light if lit in the above
sequence.
4. Once lit adjust the primary air disk to provide a clean
blue flame.
5. Place cooking pot onto ring burner.
AFTER USE
Turn the gas cylinder valve off and wait for the flame
to go out. Then turn the appliance gas valve off.
LIGHTING PROCEDURE
Problem Possible Reason Solution
Burner will not ignite Valve on gas bottle closed Open valve on gas bottle
Control knob is closed Turn knob onto high when lighting
Food is not cooking or
is taking too long
Burner has gone out Check that the gas bottle is not empty
and re-ignite burner
Regulator and hose
will not fit my cylinder
Your gas cylinder is a POL style gas
cylinder connection
Swap your gas cylinder for a gas
cylinder the safer LCC27 Safe Lok
gas cylinder connection
Gas valve and burner ring matching.
RB2SL
RB3SL
RB4SL
Primary Air Disk
Gas Inlet
Gas Valve “ON”
Gas Valve “OFF”
67
For any queries or assistance call
Customer Service
(Australia Only)
1300 174 876
Hours of operation:
Monday to Friday 8am - 5pm EST
Do not return to place of purchase.
Keep your purchase receipt, this will be required to make any claims under the 1 year warranty.
The gas valve can be adjusted from “OFF to “HIGH”
and this will affect the cooking time.
Gas Valve “ON” Max.
The gas lever is in a straight line with the gas valve
to the venturi tube.
Gas valve “OFF”
The gas lever is at right angles to the gas valve
and the venturi tube.
Spillage
Turn off the cylinder gas valve. Wait for the flame
to go out. Using heat proof gloves:
• Remove cooking pan.
• Blow liquid from burner ports.
• Tip burner upside down to drain spilled liquid.
• Once dry re-position.
• Follow lighting procedures to re-light burner
and continue cooking.
IMPORTANT
• Do not smoke when attempting to ignite
appliance.
• Always use protective gloves when handling
hot components.
• Do not smoke at any time when attempting
to ignite the appliance burners.
• Caution: Do not move the appliance while
in operation.
• Do not leave the appliance unattended
when alight.
NOTE: ONLY USE ON A NON-COMBUSTIBLE
SURFACE
USE ONLY ON THE SOLID GROUND
OPERATING PROCEDURE
SAFE APPLIANCE LOCATIONS
This appliance shall only be used in an above ground open-air situation with natural ventilation, without stagnant
areas, where gas leakage and products of combustion are rapidly dispersed by wind and natural convection.
Only use on a Non-combustible surface.
Any enclosure in which the appliance is used shall comply with the following:
An enclosure with walls on all sides, but at least one permanent opening at ground level and no overhead cover.
Within a partial enclosure that includes an overhead cover and no more than two walls.
Within a partial enclosure that includes an overhead cover and more than two walls,
the following will apply:
at least 25% of the total wall area is completely open, and
at least 30% of the remaining wall area is open and unrestricted.
In the case of balconies, at least 20% of the total wall area shall be and remain open and unrestricted.
DIAGRAMMATIC REPRESENTATIONS OF OUTDOOR AREAS
The following figures are diagrammatic representations of outdoor areas.
Rectangular areas have been used in these figures – the same principles apply to any other shaped area.
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Quemador de Gasmate
