Garz Fricke SANVITO 10.1 WM V2.1 Manual de usuario

WE MAKE IT YOURS

SANVITO 10.1 WM V2.1

ARM Cortex A9

Product Manual

Revision Date Author Description

V 1.0 29.01.2020 CG Initial document release for PCB revision V2.1

PRODUCT MANUAL

SANVITO

Document Revision History

The information in this document is subject to change without prior notice in order to improve reliability, design

and function and does not represent a commitment on the part of the manufacturer.

Online support on www.garz-fricke.com

PRODUCT MANUAL

SANVITO

Table of Contents

1. Introduction ....................................................................................... 4

2. Safety Hints........................................................................................ 5

3. Product Introduction ......................................................................... 6

3.1 Serial number..........................................................................................6

3.2 Related Documents and Online Support.................................................7

4. Technical Data.................................................................................... 8

4.1 Block Diagram SBC.................................................................................9

4.2 Connectors ..............................................................................................10

5. External Interfaces ACC MT ............................................................... 11

5.1 DC Power Supply .....................................................................................11

5.2 RS485.......................................................................................................11

5.3 Digital In/Out............................................................................................12

5.4 Ethernet 1 ................................................................................................12

5.5 USB Host..................................................................................................13

5.6 USB OTG ..................................................................................................13

5.7 Micro SD card holder...............................................................................14

5.8 Expansion Board Connector PCIe ...........................................................15

5.9 Figure Mainboard ...................................................................................16

6. Wall Installation Instructions............................................................. 17

6.1 On-Wall Cable Mounting with Cable Inlet ...............................................17

6.2 Wall Installation.......................................................................................18

Annex A: Technical Drawing.............................................................................. 20

Annex B: Quality and Incoming Inspections ...................................................... 21

B-1 Display and Touch....................................................................................21

Annex C: Hardware Revision Information ......................................................... 22

Annex D: Guidelines and Standards .................................................................. 23

D-1 RoHS Declaration ....................................................................................23

D-2 Supplier Declaration – Directive EG 1907/2006 REACH .........................23

D-3 UL Certification........................................................................................23

D-4 Garz & Fricke Conformity Statement......................................................23

Annex E: Technical Support ............................................................................. 24

Annex F: General Information .......................................................................... 25

* alternative assembly upon request

PRODUCT MANUAL

SANVITO

1. Introduction

Thank you very much for purchasing a Garz & Fricke product. Our products are dedicated to professional use

and therefore we suppose extended technical knowledge and practice in working with such products.

The information in this manual is subject to technical changes, particularly as a result of

continuous product upgrades. Thus this manual only reflects the technical status of the

products at the time of printing. Before design-in the device into your or your customer’s

product, please verify that this document and the therein described specification is the latest

revision and matches to the PCB version. We highly recommend contacting our technical sales

team prior to any activity of that kind.

Please also verify all herein described specifiations carefully before transfering them to your

own documentation for the end-product to ensure their validity for your installation conditions.

The attached documentation does not entail any guarantee on the part of Garz & Fricke GmbH

with respect to technical processes described in the manual or any product characteristics set

out in the manual. We do not accept any liability for any printing errors or other inaccuracies in

the manual unless it can be proven that we are aware of such errors or inaccuracies or that we

are unaware of these as a result of gross negligence and

Garz & Fricke has failed to eliminate these errors or inaccuracies for this reason.

Garz & Fricke GmbH expressly informs that this manual only contains a general description of

technical processes and instructions which may not be applicable in every individual case. In

cases of doubt, please contact our technical sales team.

In no event, Garz & Fricke is liable for any direct, indirect, special, incidental or consequential

damages arising out of use or resulting from non-compliancy of therein conditions and

precautions, even if advised of the possibility of such damages.

Distribution of this document to third parties is prohibited.

Before using a device covered by this document, please carefully read the applied master

supply agreement.

Embedded systems are complex and sensitive electronic products. Please act carefully and

ensure that only qualified personnel will handle and use the device at the stage of development.

In the event of damage to the device caused by failure to observe the hints in this manual

and on the device (especially the safety instructions), Garz & Fricke shall not be required to

honour the warranty even during the warranty period and shall be exempted from the statutory

accident liability obligation. Attempting to repair or modify the product also voids all warranty

claims.

PRODUCT MANUAL

SANVITO

2. Safety Hints

Please read this section carefully and observe the instructions for your own safety and correct use of the device.

Observe the warnings and instructions on the device and in the manual. Garz & Fricke embedded systems have

been built and tested by us and left the company in a perfectly safe condition.In order to maintain this condition

and ensure safe operation, the user must observe the instructions and warnings contained in this manual.

I. General Handling

Don’t drop or strike the unit: The PCB, display and/or other parts might be damaged.

Keep away from water and other liquids, the unit is not protected against.

Operate the unit under electrical and environmental conditions according to the technical

specification.

The electrical installations in the room must correspond to the requirements of the local

(country-specific) regulations.

Take care that there are no cables, particularly power cables, in areas where persons can trip

over them.

Do not place the device in direct sunlight, near heat sources or in a damp place.

All plugs on the connection cables must be screwed or locked to the housing.

Repairs may only be carried out by qualified specialist personnel authorized by

Garz & Fricke GmbH or their local distributors.

Maintenance or repair on the open device may only be carried out by qualified personnel

authorized by Garz & Fricke GmbH which is aware of with the associated dangers.

II. Electricity

The embedded systems may only be opened in accordance with the description in this user’s

manual for

- replacing of the (rechargeable, where applicable) lithium battery and/or

- configuration of interfaces, where applicable

These procedures have to be carried-out only by qualified specialist personnel.

When accessing internal components the device must be switched off and disconnected from

the power source.

When purchased core or basic versions without protecting back cover, don’t touch the PCB

directly with your fingers. Especially these products need to be handled very carefully.

Don’t operate or handle the unit without typical ESD protection measures, such as ground

earthing.

Operate the unit according to the technical specification only.

III. Damage or Permanent Malfunction

It must be assumed that a safe operation is no longer possible, in case

-the device has visible damage or

-the display is dark or shows strange pattern for longer period

-the device doesn’t react after a reset

In these cases the device must be shut down and secured against further use

SANVITO x2 10.1 WM IPS V1.2

900- 3891R

1.25 A 24 V

0º C T 40º C

Garz & Fricke GmbH

Schlachthofstrasse 20

21079 Hamburg

Made in Germany

PRODUCT MANUAL

SANVITO

3. Product Introduction

The "SANVITO 10.1 WM V2.1" is a control and operating unit for various applications.

3.1 Serial number

For service and later identification of the device a label containing the serial number and its QR-code is

located on the Device.

Serial Number

Flash-N-Go

http://mx31.de/b

Contains information about the usage of the G&F Flash-N-Go solution

which consists of three submodules:

Flash-N-Go Boot (A tiny boot loader)

Flash-N-Go System (A maintenance os)

Flash-N-Go Update (A GUI based update solution for all os)

Linux Yocto Jethro

http://mx31.de/9

Contains information about Linux BSP with

development environment Linux Embedded System Yocto (Codename:

Jethro, Version 3.0) includes first information about the bootloader

Flash-N-Go

PRODUCT MANUAL

SANVITO

3.2 Related Documents and Online Support

This document contains operating system specific information. The following additional documentations are

available:

OPERATING SYSTEMS

UPDATE / BOOT / SYSTEM

PRODUCT MANUAL

SANVITO

4. Technical Data

Type x2l

CPU Type

i.MX6 Dual

Core Class

ARM Cortex - A9

Core Clock

1 GHz

Features

NEON for SIMD media acceleration and VFP operations; Multi-format HD 1080p video de-coder and HD

720p video encoder hardware engine.

1 MB L2 cache

GPU

Vivante GC 2000+ (4 shaders)

Vivante GC 355

Vivante GC 320, 2 Layer composition

HW Accelerators

OpenGL ES 1.1/ 2.0/ 3.0 & Haiti,

OpenGL 1.1 EP,

Open GL 1.1

RTC

Accuracy: +/- 30 ppm at 25°C

Memory

eMMC Flash

4 GB PSLC MMC Flash (8 GB in MLC Mode)

RAM Standard

1GB 64 bit DDR3L

SD Card Slot

4 bit MMC/SDIO/SD/SDHC

Operating Systems

Supported OS

Linux Yocto, Android

Communication Interfaces

Network

1x 10/100 Mbit/s Ethernet (RJ-45)

USB

1x 480 Mbit/s Host (Type A)

RS-485

1x RS-485 galvanic isolated

Miscellaneous

Sensors

Ambient Light Sensor

LED

2 colour status LEDs

Audio

Audio Internal

2x Speaker 1.0 W; RMS (8 Ω)

Micro Internal

Display and Touch

Size

10.1 inch/ 255.85 mm

Resolution

1280 x 800 pixel

Brightness

Typ. 420 cd/ m

Backlight Lifetime

Min. 50 000 h

Viewing Angle

85°, 85°, 85°, 85° (UDRL)

Color

24 bit (16.7 Mio. colors)

Touch

projected capacitive single touch

Housing

Front

3.0mm thoughened glass, RAL 9005, optical bonded with touch and display

Frame

Fine zinc alloy, matt chrome

Rear

ABS-PC/ 1.4016 stainless steel

Ingress Protection

IP30

Device Dimensions

W x H x D

271.4 x 188.2 x 41.7 mm

Weight

1939 g

Power Supply

Supply Voltage

Nom. 24 V DC or PoE+ (802.3at)

Consumption

Typ. 10.2 W; max.25.5 W

Typical Environmental Conditions

Storage Temperature

-20 to +70°C

Operating Temperature

0 to +60°C

Humidity

5 to 90% RH

Expansion Cards

Extension Card

tbd.

PRODUCT MANUAL

SANVITO

4.1 Block Diagram SBC

Tbd.

Pos. Description

1DC Power Supply

2Ethernet

3Factory Reset

4Digital In/Out

5 RS 485

6Expansion Boar Connector PCIe

7Micro SD card holder

8USB OTG

9USB Host

10 Reset

PRODUCT MANUAL

SANVITO

4.2 Connectors

As this manual describes a core version, the internal and external interfaces will be mentioned in the following

chapter.

Tabla de contenidos

Manuales populares de Panel táctil de otras marcas

FlowLine

FlowLine Data loop Manual de usuario

ALPEX

ALPEX AEx-8 P Series Manual de usuario

Ltech

Ltech E5S Manual de usuario

Harman

Harman AMX MODERO S MSD-701-L2 Manual de usuario

Acnodes

Acnodes PC 1150 Manual de usuario

AIS

AIS IP10IA99 series Manual de usuario

IBASE Technology

IBASE Technology ASTUT-152-RE1S Manual de usuario

YASKAWA

YASKAWA TP 610C Manual de usuario

B&R

B&R Power Panel C Series Manual de usuario

Beijer Electronics

Beijer Electronics X2 control Manual de usuario

AXIOMTEK

AXIOMTEK GOT321W-521 Manual de usuario

TRIDONIC.ATCO

TRIDONIC.ATCO x-touchBOX Manual de usuario

Qomo

Qomo QIT1386 Manual de usuario

DFI

DFI KS104-CD Manual de usuario

AMX

AMX AXP-PPC Guía

Sartorius

Sartorius X3 PR 5410 Manual de usuario

AMX

AMX Modero X Series Manual de usuario

Advantech

Advantech TPC-30 Series Manual de usuario