Gardner Denver THOMAS SK927 Manual de usuario

MODEL SK927

COMPRESSOR SERVICE KIT

CAUTION: Improper assembly or use of damaged parts may lead to

premature failure. To avoid frequent repairs follow these assembly

procedures.

NOTE: Before you begin read these instructions thoroughly. Assemble the

necessary tools. You will need a at tip and phillips head screw driver as well as a

T-20 and T-25 Torx driver for a torque wrench.

WARNING: Unplug the compressor before beginning disassembly.

ALWAYS NOTE POSITION AND ORIENTATION OF PARTS AS REMOVED

TO ASSURE CORRECT POSITIONING WHEN REASSEMBLING.

For service to 917/927 Series Compressors

FILTER REPLACEMENT

1. Remove lter cap.

2. Remove old lter and discard.

3. Wipe inside of lter body and cap with a clean soft cloth.

4. Place new lter inside of lter body.

5. Replace cap.

Filter Cap

Filter

Filter Body

621102 Valve Flapper

Intake & Exhaust (2)

633560 Gasket O-Ring

625223 Valve Plate

Screws (5)

625540 Diaphragm

Hold Down Screws (4)

625444 Head Screws

(6)

608212 Diaphragm

625160 Valve Flapper

Screws (2)

641034 Filter

617045 Valve Keeper

Strip (2)

3524 Washington Avenue, Sheboygan, WI 53081 USA

(920) 452-4891 www.gd-thomas.com

Hold Down Plate

Screw

Diaphragm

Connecting

Rod

Hold Down

Plate

DIAPHRAGM REPLACEMENT

1. Remove head.

2. Remove four screws from hold down plate. Discard screws.

3. Remove hold down plate, diaphragm and diaphragm liner (if present) from connecting

rod top. Wipe connecting rod top and hold down plate with a clean soft cloth.

4. Center new diaphragm and hold down plate over connecting rod holes. Make sure

all holes align as shown in the illustration below and that the diaphragm is centered

in the well of the housing. Insert four new screws. Torque screws to 20 in- lbs. in

criss-cross pattern.

5. Replace head and valve plate assembly. Torque screws to 40 in- lbs. in a criss-cross

pattern.

INTAKE & EXHAUST VALVE REPLACEMENT

1. Remove 4 head screws and head. Discard

screws. Turn head over. Remove 4 screws

from valve plate. Discard screws. Remove

valve plate from head. NOTE: If valve plate

needs to be pried out of head cavity, be careful

that the intake hole seat area does not get

damaged. If damage should occur the valve

plate will need to be replaced.

2. Remove and discard gasket.

3. Remove screw, apper and keeper from top

side of valve plate, discard. Wipe valve plate

and head with a soft clean cloth. Reassemble

new flapper and keeper with new screw.

Torque to 10 in- lbs. Make sure the end of

the apper covers the intake hole and that

the keeper is aligned properly. Turn valve

plate over and repeat procedure on exhaust

apper.

4. Wipe inside of head with a clean soft cloth, be

sure to remove any excess gasket. Install new

gasket.

5. Replace valve plate in head. (See Fig. #1).

Insert 4 new screws. Torque valve plate

screws to 40 in- lbs.

6. Replace head. Torque screws to 48 in- lbs. in

a criss-cross pattern.

Valve

Keeper

Valve

Flapper

Gasket

Valve Plate

Screw

Head

Otros manuales de Compresor de aire de Gardner Denver

Gardner Denver

Gardner Denver CHAMPION ROTORCHAMP EFB99B Manual de servicio

Gardner Denver

Gardner Denver INTEGRA EFB99A Manual de servicio

Gardner Denver

Gardner Denver VS80A Manual de servicio

Gardner Denver

Gardner Denver L15 Instrucciones de instalación

Gardner Denver

Gardner Denver ELECTRA-SAVER II Manual de servicio

Gardner Denver

Gardner Denver ELECTRA-SCREW EDEQHH Manual de servicio

Gardner Denver

Gardner Denver Champion ROTORCHAMP EFD99A Manual de servicio

Gardner Denver

Gardner Denver L07 Manual de servicio

Gardner Denver

Gardner Denver AirSmart Controller APEX5-15A Manual de servicio

Gardner Denver

Gardner Denver GD150 Manual de usuario

Gardner Denver

Gardner Denver INTEGRA EFC99A Manual de servicio

Gardner Denver

Gardner Denver INTEGRA EFA99F Manual de servicio

Gardner Denver

Gardner Denver TR20 Rear CW Manual de usuario

Gardner Denver

Gardner Denver L Series Manual de servicio

Gardner Denver

Gardner Denver ELECTRA-SAVER Manual de servicio

Gardner Denver

Gardner Denver L30-45E Manual de usuario

Gardner Denver

Gardner Denver L Series Guía de solución de problemas

Gardner Denver

Gardner Denver Electra-Screw EDEQHF Manual de servicio

Gardner Denver

Gardner Denver APEX15-18A Manual de servicio

Gardner Denver

Gardner Denver ELECTRA-SAVER G2 Manual de servicio

Gardner Denver

Gardner Denver L90 7.5A V4 Guía rápida

Gardner Denver

Gardner Denver EBB BB-7.5 HP Manual de servicio

Gardner Denver

Gardner Denver L Series Manual de servicio

Gardner Denver

Gardner Denver L Series Manual de servicio

Manuales populares de Compresor de aire de otras marcas

Sparmax

Sparmax DC-25XR Manual de usuario

KAESER

KAESER M122 Manual de usuario

GMC

GMC GAC1500 Manual de usuario

Briggs & Stratton

Briggs & Stratton Air Compressor Manual de usuario

Fini

Fini F3GST2TK Manual de usuario

Industrial Air

Industrial Air CP1580325 Manual de programación

Campbell Hausfeld

Campbell Hausfeld RP3300 Guía de inicio rápido

Ingersoll-Rand

Ingersoll-Rand UP6 20 HP Manual de usuario

Hitachi

Hitachi EC99S Manual del operador

Parkside

Parkside PKO 270 A1 Manual de usuario

Sullair

Sullair 185 Manual de usuario

Clas Ohlson

Clas Ohlson QIE-ZTH-15 Manual de usuario

Ferm

Ferm CRM1046 Manual de usuario

BE AC153 Manual de usuario

RIDGID

RIDGID OF25150A Manual de usuario

Johnson Controls

Johnson Controls QUANTUM LX Manual

Sears

Sears Craftsman 919.167463 Manual de usuario

Ring Automotive

Ring Automotive RAC700 Manual de usuario