Garagedoor Lock Pro 135 A Series Guía de instalación
Installation and Operating
Guide for the garage door
lock
Pro-Series 135 A
Random-Code Remotes allow secure
wireless control of the locking system
Note: Exterior Key Release, Pull Cable Kit, must be
installed on single entry or vaulted garages.
Introduction and Table of Contents
Read these instructions completely prior to installation, pay special
attention to WARNINGS, CAUTIONS and order of installation steps.
Make sure your garage door and operator are in good working
order prior to lock installation.
The first section of this instruction manual covers lock-head
installation on roll up garage doors. The second section covers the
changes to accommodate lock-head installation on one piece doors.
Refer to steps 1, 2, 3, 7, ,9, 13, 14, 15 and 16 in the first section
for one piece door installs.
The figures in this instruction manual are in order according to
the steps. However you may need to review some figures out of
order, as a reference to help execute the task at hand correctly.
Table of contents:
Introduction 1
Required Tools 3
Page 1
Hardware Kit Contents 4
Unpacking & Layout 5
Preparing Door Operator 6
Warning Sheet 7
Preparing Door 8
Marking Door For Correct Lock-Head Position 9
Mounting The First Lock-Head 10
Routing wire. 17
Mounting The Second Lock-Head 11
Fastening Wire Cable to Door 12
Making Receiver Holes In Track 13
Installing Red L.E.D. 14
LED Install Through Door Panel 15
Mounting Plastic Bracket To Track 16
Suspending Wire Harness From Header to Operator 18
Mounting Electrical Control Box 19
Mounting Magnetic Door Switch. 20
Powering Up. 25
This Section Is For One Piece Doors ONLY 21
How To Mount Lock-Head (A) and (B) On a One Piece Door. 22
23
Metal Wire Harness Bracket For One Piece Doors
One Piece Door Magnetic Switch Installation 24
How To Change Batteries 30
Warranty Limitations and Guidelines 31
Troubleshooting 32
Second section for one piece garage doors
Operating Instructions
Learning and Unlearning the Remotes to the Control Box. 26
Activating and Deactivating Auto Close and Lock Feature. 27
Safety,Warnings and Cautions 2
Replacement Parts and Accessories 29
Power out manually operating lock 28
Safety,Warnings and Cautions Page 2
IMPORTANT INSTALLATION INSTRUCTION
! WARNINGS !
To reduce the risk of severe injury or death:
1. READ AND FOLLOW ALL INSTALLATION WARNINGS AND INSTRUCTIONS
2. Install garage door lock only on properly balanced and lubricated garage door. An improperly balanced door may not reverse
when required and could result in SEVERE INJURY or DEATH.
3. All repairs if needed, to cables, spring assemblies and other hardware MUST be made by a trained door systems technician
BEFORE installing the lock.
5. NEVER wear watches, rings or loose clothing while installing or servicing lock or operator. They could be caught in garage
door, lock, or operator mechanisms.
4. NEVER connect garage door lock to power source until instructed to do so.
6. To prevent possible SERIOUS INJURY or DEATH: ALWAYS call a trained door systems technician if garage door
binds, sticks, or is out of balance. An unbalanced garage door may not reverse when required.
7. ONLY operate garage door lock and operator at 110VAC 60HZ to avoid malfunction and damage.
8. Without a properly working safety reversal system, persons (particularly small children) could be SERIOUSLY INJURED
or KILLED by a closing garage door.
Safety,Warnings and Cautions
9. To prevent INJURY from pinching, Keep hands, and fingers away from the joints while installing and testing the lock
system on the garage door.
10. Review the SAFTEY GUIDE in the operator owners manual.
While installing the GARAGE DOOR LOCK use common sense. If you are unclear on the instructions or if you do
not feel comfortable installing the lock system contact a qualified service technician.
Page 3
FCC Guideline
Changes or modifications not expressly approved by Elocksys, Inc.
could void the user's authority to operate the equipment.
This product has been tested and complies with the specifications for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used according to the instructions, may cause harmful interference to
radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television
reception, which is found by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna
Increase the separation between the equipment or devices
Connect the equipment to an outlet other than the receiver's
Consult a dealer or an experienced radio/TV technician for assistance
Required Tools
Drill
5/64”, 1/8” Drill bit
5/16”, 3/8” Drill Bitts
7/16” Wrench
½” Wrench
Side Cutters
Pliers
Pocket Phillips screw driver
Pencil
#2 Phillips screw driver
Flat blade screw driver
#2 Phillips bit
16 foot tape M easure Medium metal file
Step Ladder
Page 4
Hammer
Hardware Kit Contents
Plastic Magnet and Bracket
#6 X ¾inch pan head-Phillips (use with #5
one hole straps)
Qty 7
#2
#12 X 3 inch pan head Phillips mounting screws
#1
Qty 4
One hole strap for wire cable Support
#7
Qty 13
#4 #8 X 2 inch screw hook
Qty 1
#6
One hole strap for M agnetic Switch
Qty 1
#15
Plastic control wire bracket
#12
1” X ¼” 20 Bolt and flange nuts for Plastic wire bracket
Qty 4
#9
Qty 1
Qty 1
#10 Staples for securing
wire
Qty 1
#11 LED Socket
Qty 10
#8
Qty 2
#13 Qty 10
7” Tie Strap
4” Tie Strap
#14
Qty 10 ft
Nylon
string
Qty 10
#5 # 8 X 1 5/8” inch Drywall screw
Page 5
Unpacking & Layout
Unpack contents from box taking extreme care not to bend or kink wire cable. Lay lock assembly on floor inside
garage with door closed. Place lock head ( A ) on your left looking at the door from inside, lock head ( B ) on right.
Lock-head (A)
Coil-cord
Manual release Leaver
Lock-head (B)
Wire cable
Control box
Antenna
110 AC power
cord
Do Not Bend or kink when
unpacking or installing the lock-heads
Remote Controls
Step 1 Page 6
This step is also used for one piece door installation.
Stop and double check to see if you have the correct lock kit for your garage door (roll up or one piece), operator
(random or fixed code) and that door size matches the lock size.
Preparing Door Operator
Random Code: Unlearn all remotes and keypads following the procedures from the manufacturers
manual or on the door operator near the learn button.
Fixed: Remove all batteries from existing remotes, key pad and store away. Place these items in the
RED bag supplied with kit.
CAUTION: YOU MUST NEVER ATTEMPT TO OPERATE THE GARAGE DOOR
OPERATOR WITH YOUR OLD REMOTES OR KEY-PAD AS LONG AS THE LOCK IS
INSTALLED ON THE GARAGE DOOR.
Such attempts will jam the lock and door resulting in damage to the door or possibly the door operator.
See Warning Sheet.
DO THIS NOW !!!
Step 2
Page 7
This step is for roll up and one piece doors. DO NOT IGNORE OR BYPASS THIS STEP.
Tabla de contenidos
