Gamma+ 8800 Els Manual de usuario
OWNER’S MANUAL
Issue 8 - January 2014
STRINGING MACHINE
8800 Els
6 POINT SC MOUNTING
2
LIMITED WARRANTY
GAMMA SPORTS warrants to the original purchaser that the 8800 Els stringing machine (“EQUIPMENT”) purchased is free
from defects in materials and workmanship for a period of ve (5) years from the date of original purchase for mechanical
parts (excluding electrical parts and string clamps), and for a period of one (1) year from the date of purchase for all electrical
parts and string clamps. Should any defects develop under normal use within the specied time periods, GAMMA will at its
option, repair or replace the defective EQUIPMENT provided it is returned to GAMMA prepaid at the purchaser’s expense.
This warranty does not apply to any damage or defect caused by negligence, abuse, misuse, unauthorized alteration, ship-
ping, handling, or part wear and tear as a result of normal use.
Routine maintenance, adjustment, and cleaning required to ensure proper operation are the responsibility of the purchaser and
are not covered under the terms of this warranty. These include, but are not limited to: String Clamp adjustment, as described
on page 20, Quick Action Clamp Base adjustment, as described on page 19, and the cleaning procedures listed on page 21.
GAMMA’s obligation under this warranty is limited to repair or replacement of defective EQUIPMENT, and no one is authorized
to promise any other liability. GAMMA shall in no event be liable for any incidental or consequential damages.
To return defective EQUIPMENT, a return authorization (RA#) must be obtained from a GAMMA customer service representa-
tive. The RA# must be marked on the outside of the shipping carton being returned. All returns must be shipped prepaid by
the customer to GAMMA. Please retain the original shipping carton and packing materials for any future shipments. GAMMA
will not be responsible for machines which are not sent in the original undamaged packaging.
A GAMMA Care Service Plan is also available through GAMMA customer service, call 800.333.0337 for details.
TABLE OF CONTENTS
WARRANTY ................................................................................................PAGE 2
FEATURES..................................................................................................PAGE 3
UNPACKING & ASSEMBLY INSTRUCTIONS ............................................ PAGE 4
POWER CONNECTION & CONTROLS ..................................................... PAGE 9
CONTROL PANEL......................................................................................PAGE 10
CONTROL PANEL FEATURES..................................................................PAGE 11
MACHINE FUNCTIONS.............................................................................PAGE 12
MOUNTING THE FRAME ......................................................................... PAGE 14
STRINGING THE FRAME .........................................................................PAGE 15
STRING LENGTH METER ....................................................................... PAGE 19
ADDITIONAL FEATURES .........................................................................PAGE 20
PATHFINDER AWL .................................................................................... PAGE 21
MAINTENANCE & ADJUSTMENTS ......................................................... PAGE 22
TROUBLESHOOTING TIPS .....................................................................PAGE 24
PARTS LIST ............................................................................................. PAGE 26
PARTS DRAWING.....................................................................................PAGE 27
8800 Els
OWNER’S MANUAL
3
MACHINE FEATURES
Electric Constant Pull Tensioner with 11.0 to 90.0 lbs Tension
Range
Digital Tension Setting with LED Display
Parallel Jaw Linear Gripper with Diamond Dust Coated
Gripping Surfaces
Professional Six Point “Self-Centering Suspension Mount”
Racquet Mounting System- Accommodates All Racquets
Professional “Switch Action” Dual Action, Rotating, Metal Fixed
String Clamps with Diamond Dust Coating
High Strength Extruded Aluminum Frame with Durable
Anodized Finish and Convenient Padded Tool Tray
Unique Internal Drawer System for Storing Tools and Adaptors
Convenient Foot Actuated Tensioner Switch
FEATURES
4
8800 Els
Unpacking Instructions & Contents
Instructions for Unpacking and Preparing for Assembly
The stringing machine is shipped in three cartons, a large master carton for the stringing
machine base with tensioner module and accessories, a medium carton for the turntable
and mounting system and a smaller carton for the oor stand post and base legs. Please
save the cartons and packing materials for possible shipments in the future. Gamma
Sports cannot be responsible for machines that are not returned, shipped in their original,
undamaged packaging. The tools you will need to assemble the machine are provided
with the machine. Due to the weight of the tensioner unit, you may need the assistance of
someone to help lift the tensioner unit out of the carton.
Once the cartons are opened, remove all inner cartons and check to be sure that all parts
are present and accounted for.
Contents of Base & Leg Carton (MMU2-72)
(1) Lower Column
(1) Upper Column with Flange Plate
(1) Floor Plate
(1) Locking Knob Screw
(4) M8 x 35 Cap Screws w/Washers
(6) M6 x 20 Cap Screws w/Washers
(1) M8 x 20 Cap Screws for Height Adjustment
(1) String Reel Holder (M8 Threaded Pin), (1) Knob, (10) Spacers, & (2) M8 Washers
Contents of Mounting System Carton (MMU2-70)
(1) Turntable Assembly w/ String Clamp Base and Mounting Stands w/ Frame Support
Slide, Side Supports, and Adapters
(2) String Clamp
(1) Package of spare plastic adapters for mounting system supports
Contents of Large Master Carton (MMU2-98)
(1) Stringer Assembly Unit w/ Tensioner Module
(1) Power Cord
(1) Foot Pedal Tensioner Switch
(1) Tool Kit (contains side cutter, bent nose pliers, needle nose pliers, starting clamp)
(1) Straight Stringers Awl & (1) Pathnder Specialty Awl
(1) Tools for assembly and maintenance
5
Floor Stand Base Assembly
The stringing machine uses a pedestal oor stand design that can be set up to orient the
machine perpendicular to the operator or to position the machine on an angle.
The base plate must be assembled to the lower column before use. Remove all parts from
the shipping carton to conrm that contents match the list of parts on Page 4.
Perpendicular Base Assembly
To assemble the Floor Stand Base to be PERPENDICULAR to the operator secure the base
placing the four 8mm bolts in the holes without the arrow.
ASSEMBLY INSTRUCTIONS
Angled Base Assembly
To assemble the Floor Stand Base to have ANGLED operator position secure the base plac-
ing the four 8mm bolts into the holes marked with an ARROW.
6
Floor Stand Upper Column Instal-
lation
With the height adjustment cap screw on the
upper column facing the brake lever & string
length meter, align the holes marked “X” in the
upper column ange with the threaded holes
in the slide brackets of the machine base.
Floor Stand Height Adjustment
The height of the machine is adjustable from
39” to 46” in approximate 1” increments. To
change the height, remove the socket head
cap screw from its current position and place
it in the appropriate hole to set the desired
height of the machine. Be sure to thread the
screw completely into the upper column so
the head of the cap screw rests in the notch
of the lower column.
"X"
"X"
"X"
"X"
ASSEMBLY INSTRUCTIONS
Floor Stand Upper Column Installa-
tion (cont.)
Secure the ange to the slide brackets in
the base of the machine with the six M6 cap
screws packed with the oor stand.
Caution: When securing the screws to
the slide brackets cross threading or over
tightening may damage the threads in the
slide bracket or cause the threads to strip out.
7
The string reel holder pin is an 8 mm rod
with threads on both ends and at surfaces
machined on one end. Thread the end of the
pin without the at surfaces into the threaded
boss on the right side of the lower column.
Using the M6 open end wrench positioned
on the at surfaces, securely tighten the pin
to the lower column.
The string reel holder can hold up to 5 reels
of string (depending on the size of the string
reel). Before placing the rst reel on the rod,
slide two M8 washers over the pin and slide
them to the boss on the lower column. After
the rst reel is placed onto the rod, place
two spacers between each reel to provide
enough space between reels and allow them
to turn freely without rubbing against one
another. (To provide a smooth feed to the
String Length Meter, place the reels on the
rod so the string spools off the reel from the
underside of the reel).
After the last reel is installed, place the re-
maining spacer(s) on the pin and attach the
threaded knob to the end of the rod.
STRING REEL HOLDER INSTALLATION
8
ASSEMBLY INSTRUCTIONS
String Clamp Installation
The post of the string clamp and tube of the
string clamp base are treated with grease to
provide protection against corrosion during
shipping and while in storage. Remove any
excessive grease with a clean cloth prior to
use. The post and tube may also be cleaned
with isopropyl alcohol. After this type of thor-
ough cleaning, the post and tube should be
treated with a light coating of machine oil to
protect the surfaces against corrosion and
to ensure smooth operation.
Turntable and Mounting System
Installation
To install the turntable remove the four nuts
holding the mounting bolts in place during
shipment. Position the turntable over the
turntable pin and align the bolts with the
holes in the ange. Secure them with the
included allen wrench.
CAUTION: If the mounting bolts are removed
or fall out during assembly be sure that the
bolts pass through the spacer inside the
turntable before securing the turntable to
the turntable pin.
9
Back Panel Features
A - Lighted Power Switch
B - A/C Power Cord Socket
C - Foot Pedal Switch Receptacle
D - String Length Meter Receptacle
Instructions for Power Connection and Controls
CAUTION ! Before connecting to the power supply, check the voltage source that the
machine is being connected to. The acceptable range of input voltages for this ma-
chine is between 100 V and 240 V @ 50 to 60 Hz. If you have any questions regarding
the input voltage supply for your area, please ask your electric utility company.
To install the power cord, insert the female end of the power cord into the AC Adapter and
then insert the female end of the cord from the AC Adapter into the A/C Power Cord Socket
“B” located on the back panel of the tensioner. Plug the male end of the power cord into a
grounded power outlet. When using extension cords, use grounded heavy duty extension
cords rated for 15 AMP service.
To connect the foot pedal switch, insert the male pin at the end of the foot pedal switch cord
into the Foot Pedal Switch Receptacle “C” located on the back panel of the tensioner.
Switch on the machine by pressing the Lighted On-Off Power Switch on the back panel. At
start-up, the machine will perform a self diagnostics check.
POWER CONNECTION & CONTROLS
Front Panel Features
A - String Gripper
B - Tension Lever Switch
C - LCD Display and Control Panel
BC
A
B DA C
WARNING! FOR INDOOR USE ONLY.
NEVER OPEN UNIT WITH POWER CONNECTED.
CHILDREN SHOULD NEVER BE PERMITTED TO OPER-
ATE THIS MACHINE WITHOUT ADULT SUPERVISION.
10
CONTROL PANEL FEATURES
ESC Button - Press to return to the
Stringing Screen from the Settings
Screen, String Length Meter Screen or
to cancel a change being made to one
of the functional settings
KNOT Button - Press once to enable
and display the Knot Icon - Press
again and hold while the Knot icon is
displayed to highlight the setting and
make changes
SOUND Button - Press to turn on or
turn off beeper. When in the Settings
Screen, the Sound Icon will include an
“X” when Beeper is disabled and “)))”
when the beeper is enabled.
PULLING SPEED Button - Press once
to display the Pulling Speed Icon - Press
again and hold while the Pulling Speed
Icon is displayed to highlight the setting
and make changes
MAIN/CROSS String Button - Press
to select and display the Main String
Tension Setting or the Cross String
Tension Setting
PRE-STRETCH Button - Press once
to enable and display the Pre-stretch
Icon - Press again and hold while the
Pre-stretch Icon is displayed to highlight
the setting and make changes
STRING LENGTH METER Button -
Press to enable and display the String
Length Meter - Pressing again will
toggle the measurement units between
feet (FT) and meters (M)
LBS/KG Button - Press to toggle the
Tension Setting between LBS and KG
ENTER Button - Press to conrm
changes to any machine settings and to
zero the String Length Meter
RETURN Button - Press to return to
the Stringing Screen from the Settings
Screen, String Length Meter Screen or
to cancel a change being made to one
of the functional settings
MEMORY Button - Press to scroll
through 9 programmable Memory
Modes (M1-M9) - Press and hold for
5 seconds to enable Basic Stringing
Mode (M0)
F1 Button - Press to display the Set-
tings Screen to view and make changes
to any of the machine settings - If no
buttons are pressed within 10 seconds
screen will revert to the Stringing Screen
F5 Button - Press to reverse the order
in which the Memory Settings are
toggled through - When LED is illumi-
nated the Memory Settings will toggle in
decreasing order
F2-F3-F4 Buttons - Press to increase
String Tension values in the tens place
(F2), units place (F3) and tenths place
(F4) and press to increase setting val-
ues for Knot, Pre-stretch and Speed
F6-F7-F8 Buttons - Press to decrease
String Tension values in the tens place
(F6), units place (F7) and tenths place
(F8) and press to decrease setting val-
ues for Knot, Pre-stretch and Speed
Otros manuales para 8800 Els
3
Tabla de contenidos
