Gainsborough Austral Lock Virtus Two Point Hinged Door Mortice... Manual de usuario
Contents
1. Lock body
2. Long plate external furniture
3. Long plate internal furniture
4 . Cylinder (not included,
length to suit door thickness)
5. Zinc spindles
6. Furniture fixing screws
7. Cylinder retaining screw
8. Fixing tabs
1. 2. 3.
Austral Aurora furniture shown
4. 5. 6. 7.
Virtus Two Point Hinged Door Mortice Lock
Installation Guide
Step 1: Door Preparation
1.1 For Flush Mount, route the door as per technical dimensions below
22.0
230.0
5.0
2 HOLES
8.6 CSK
2 HOLES
R2.5 x 4
104
160
87.0
84.5
101.5
17
59.5
122.5
10
30
9 x 2 HOLES
20
16
8
37 REF
R10
1000 mm
TO THE BOTTOM OF THE DOOR
(RECOMMENDED)
35.4
40 60
FLUSH MOUNT INSTALLATION
30mm BACKSET 40mm BACKSET 60mm BACKSET
8.
Step 1: Door Preparation (cont.)
1.2 For Face Mount, route the door as per technical dimensions below
192.0
21.0
3.2
2 HOLES
R2.5 x 4
88.5
68.0
144.5
84.5
17
122.5
8
16
10
59.5
R10
9 x 2 HOLES
20
101.5
37 REF
1000 mm
TO THE BOTTOM OF THE DOOR
(RECOMMENDED)
35.4
30mm BS
routing is 27.5mm
from face
TOP VIEW OF STILE
SIDE VIEW OF STILE
FRONT VIEW
OF STILE
40mm BS
routing is 37.5mm
from face
60mm BS
routing is 57.5mm
from face
FACE MOUNT INSTALLATION
30mm BACKSET 40mm BACKSET 60mm BACKSET
Step 2: Installing the Lock
2.1 Insert lock into the stile
2.2 Secure with screws (max length 12mm)
Use fixing tabs for flush mount installation
Fixing tab
Fixing tab
Step 4: Re-handing & Latch Adjustment
4.1 Check latch to determine if handing
is correct
4.2 To re-hand the latch, remove cap,
turn the latch, head screw counter-
clockwise with a manual screw driver
until the back of the latch comes out
of the faceplate so it can be rotated
4.3 Rotate the latch head 180 degrees
and re-tighten the screw fixing
4.4 To increase the latch projection
turn the latch screw counter-clockwise
4.5 Latch projection can be increased
by a maximum of 2mm from original
position
4.6 Replace cap after adjustments are
complete
Step 3: Mounting Accessories
3.1 Insert the spindle into the
square hub of the lock
3.2 Insert the cylinder into the
cylinder hole and secure with
the cylinder retaining screw
3.3 Mount the internal and
external hardware onto the
spindle and cylinder
3.4 If using snib furniture, align snib
arm to snib slot in lock body
3.5 Secure furniture with supplied
fixing screws
Step 5: Lock Operation Check
5.1 Close the door firmly
5.2 Operate the cylinder turn or key
to extend the deadbolt
5.3 Handle will be locked and
deadbolt will prevent the door
from opening
1800 098 094
info.au@allegion.com
ausloc.com
©Allegion 2023
PDAU0005
Tabla de contenidos
Otros manuales de Cerradura de puerta de Gainsborough
Gainsborough
Gainsborough TRILOCK G1 Series Manual de usuario
Gainsborough
Gainsborough TRILOCK OMNI BB 8955 Series Manual de usuario
Gainsborough
Gainsborough Austral Lock Virtus Four Point Hinged Door Mortice... Manual de usuario
Gainsborough
Gainsborough Z5R Series Manual de usuario
Gainsborough
Gainsborough SD8 Manual de usuario
Gainsborough
Gainsborough Trilock Traditional Series Manual de usuario
Gainsborough
Gainsborough G+ LOCKSET Manual de usuario
Gainsborough
Gainsborough Contemporary Series Manual de usuario
