Gaggenau GI 976 760 Manual de usuario

ENGLISH - 1

ENGLISH

www.gaggenau.com/us

INTRODUCTION ........................................................... .2

TOOLS AND MATERIALS NEEDED ................................... .3

MATERIALS SUPPLIED .................................................. .4

CHOOSING A LOCATION ............................................... .5

PLUMBING PREPARATION .............................................. .6

ELECTRICAL PREPARATION ........................................... .7

PLACING THE DISHWASHER .......................................... .8

DRAIN HOSE CONNECTION ............................................ .9

HOT WATER CONNECTION ............................................ 10

ELECTRICAL SUPPLY CONNECTION ................................. 11

GROUNDING INSTRUCTIONS ................................. 11

DOOR PANEL INSTALLATION .......................................... 12

INAL ADJUSTMENTS ................................................... 13

INAL CHECKLIST ........................................................ 14

IMPORTANT: Before you begin, read t ese instructions completely and carefully.

INSTALLER: Please leave t is manual wit owner for future reference.

OWNER: Save t ese installation instructions for local

electrical inspector’s use and for future reference.

TABLE OF CONTENTS

2 - ENGLISH www.gaggenau.com/us

INTRODUCTION

In addition to these instructions the dishwasher shall be installed:

• In the United States, in accordance with the National Electric

Code/State and Municipal codes and/or local codes.

• In Canada, in accordance with the Canadian Electric Code

C22.1 -latest edition/Pro incial and Municipal codes and/or

local codes.

Please read these installation instructions completely and carefully.

They will save you time and effort and help to ensure optimum dishwasher

performance.

•NEW INSTALLATION - If the dishwasher is a new installation, most of the work

must be done before the dishwasher is moved into place.

•REPLACEMENT - If the dishwasher is replacing another dishwasher, the

connections for the dishwasher being replaced must be checked for

compatibility with the new dishwasher and replaced as necessary.

IMPORTANT

Be sure to observe all listed

warnings and cautions. (Look for

the triangles with exclamation marks

inside.)

NOTE: Please do not discard any bags or items that come with the

original package until after the entire installation has been completed!

After unpacking the dishwasher and prior to installation, thoroughly inspect the

dishwasher for possible freight or cosmetic defects. Report any defects immediately.

Cosmetic defects must be reported within 30 days of installation.

INSPECT THE DISHWASHER

THESE INSTALLATION INSTRUCTIONS ARE INTENDED

FOR USE BY QUALIFIED INSTALLERS.

WARNING

CAUTION

01Bosch

ENGLISH - 3

ENGLISH

www.gaggenau.com/us

TOOLS & MATERIALS NEEDED

Tools Needed for Installation

Additional materials may be required to comply with local codes.

Figure 2

Materials Needed

Hot Water Su ly Line - Minimum 3/8”

O.D. copper tubing or metal braided

dishwasher supply line.

Shut-off valve and fittings for hot water

supply line.

90° elbow with 3/8” N.P.T. external threads

on one end and sized to fit your water

supply line on the other end.

UL listed conduit connector or strain relief.

3 twist-on wire connectors for 16 AWG

wire.

Teflon tape or other pipe thread compound

which help seal plumbing connections.

Electric Connection - 2 conductor, 1 ground

insulated electrical supply cable (30” or

sufficient length for your installation).

TAPE

Figure 1

Hole saw or 1 hole cutter

Level

Torx screwdriver, #20

Phillips screwdriver (#2)

Slotted screwdriver (#2)

Ad ustable wrench,

(size med., 2 reqd.)

Wire stripper

Wire Cutter

Pipe wrench, 2 reqd.

Electric Drill

Tape Measure

Hammer

osch

4 - ENGLISH www.gaggenau.com/us

MATERIALS SUPPLIED

GI MODEL Dishwasher

Installation Kit

B . Toe Panel Screws (8mm) (2)

C. Mounting Brackets (1L & 1R)

D. Mounting Bracket Screws (2)

E. Rubber onnection Hose (1)

and Drain Hose lamps (2)

A. ap (2 Blk)

I. Wood Screws (2)

G. Mounting Door Brackets(2 plastic)

w/Screws (4) and;

Mounting Door Brackets (2 metal)

w/Screws (4)

F. Spring Tension Screw (2)

Man al Bag

All Dishwashers come with a manual bag.

The following contents are located in every

bag:

•Use & are Manual

•Installation Instructions

J. Tall Item Sprinkler (1)

H. SHV Installation Template

(excluding the GM model dishwasher)

Note: Pictures are not to scale.

Figure 3

Accessory Parts for your model dishwasher

will come in one or more plastic bags. heck

to make sure that the parts supplied for your

model are all there. See Figure 3. If any

parts are missing contact your dealer

immediately.

Accesso y Pa ts Supplied

GM MODEL Dishwasher

Installation Kit

B . Toe Panel Screws (8mm) (2)

C. Mounting Brackets (1L & 1R)

D. Mounting Bracket Screws (2)

E. Rubber onnection Hose (1)

and Drain Hose lamps (2)

A. ap (2 Blk)

F. Spring Tension Screw (2)

K. Torx 15 (1)

L. Allen Wrench (1)

ENGLISH - 5

ENGLISH

www.gaggenau.com/us

Select a location as close to the sink as

possible for ready access to water and drain

lines.

Most of the installation work is done before

the dishwasher is moved into place.

Any built-in dishwasher must be fully

enclosed on the top, both sides and back.

Therefore the cabinet space below your

counter is probably the best location.

Choosing the Location

CHOOSING A LOCATION

If the dishwasher is to be installed in a

corner, make sure there is adequate clea-

rance to open the door. See Figure 6.

For proper operation and appearance of the

dishwasher, the cabinet opening should be

square and have dimensions as shown in

Figure 5.

Figure 6

Door in

open

position

Clearance

for door

opening Dishwasher

Countertop

Cabinet Opening Dimensions

Table 1 - see Figure 4

THESE INSTALLATION

INSTRUCTIONS ARE

INTENDED FOR USE BY

QUALIFIED INSTALLERS

Figure 5

Figure 4 4” (102mm)

1-15/16” (49mm)

3-1/2” (90mm)

NOTE: This dimension will vary by model

due to control panel differences.

&067679IG 067672MG &067669IG 066672MG

AthgieH.nim)mm068("8/733 )mm018("8/713 .nim

BhtdiW.nim)mm806("61/5132 )mm806("61/5132 .nim

ChtpeD.nim)mm375("61/922 )mm375("61/922 .nim

&067679IG 067672MG &067669IG 067662MG

AthgieH.nim)mm468("43 )mm418("61/123 .nim

BhtdiW "8/142-"8/532 .nim)mm316-006( "8/142-"8/532 .nim)m316-006(

ChtpeD.nim)mm016("42.nim)mm016("42

Table 2 - see Figure 5

Overall Dishwasher Dimensions

90° 90°

6 - ENGLISH www.gaggenau.com/us

PLUMBING PREPARATION

1. In order to reduce running time, Gaggenau recommends 140° F water inlet

temperature. Your dis was er will perform equally as well at 120° F water

temperature, but t e run time will be extended.

Hot Water S pply

• The hot water line to the dishwasher

must provide between 5 - 120 psi (0.3-

8.27 bars) water pressure.

• The hot water heater should be set to

deliver 140°F (60° ) water

temperature to the dishwasher.¹

• A 3/8” minimum O.D. copper tubing

inlet line is recommended.

• All solder connections must be made

before water line is connected to the

dishwasher’s inlet water valve. Do not

solder within 6 inches (152.4 mm)

of the dishwasher s inlet water

valve.

• Drill a 1” (25.4 mm) diameter access

hole in the cabinet for the water supply

line (Figure 9A).

• Run the line to the approximate fill

valve location, as shown in Figure 9A.

It is recommended that a shut-off valve (not

supplied) be installed in the hot water

supply line in a readily accessible location,

see Figure 9.

NOTE: If connection to an air gap is

required by local code, air gap kits are

available from local plumbing sources.

Install the air gap according to the

manufacturer’s instructions.

Drain Hose

The dishwasher comes with a seven (7)

foot drain hose.

• A 1.25” access hole must be made to

allow the drain hose to be run to the

drain connection location.

Figure 7

IMPORTANT

If no ai gap is used and the d ain

line is un into a sink o dispose ,

the d ain line must be elevated to

a point highe than the highest

wate level of the sink to p event

back siphoning into the

dishwashe .

THESE INSTALLATION

INSTRUCTIONS ARE

INTENDED FOR USE BY

QUALIFIED INSTALLERS

CAUTION

To protect against possible rupture of

the fill valve, water lines leading to

the dishwasher, as well as water lines

in the dishwasher MUST be protected

against freezing. If the valve or water

line freezes, flooding may occur. Such

ruptures are not covered by the

warranty.

Electrical supply cable

Hot water

line

Drain

Hose

ENGLISH - 7

ENGLISH

www.gaggenau.com/us

ELECTRICAL PREPARATION

• ut a 1” (25.4mm) diameter hole in the

cabinet (in area of Figure 9 B). For wood

cabinets, sand the hole until smooth.

For metal cabinets, cover the edge with

a grommet.

• Run flexible cable (as codes permit) from

junction through hole in cabinet. able

should extend 30” (762 mm) from back

wall.

Electrical S pply

It is the customer’s responsibility to insure

that the dishwasher installation is in

compliance with all national and local

electrical codes and ordinances. The

dishwasher is designed to operate with a

120V, 60Hz, A only electrical supply.

onnect to a separate electrical circuit with

a fuse or circuit breaker rated for 15 Amps.

A 20 Amp fuse or circuit breaker may be

used if the dishwasher is connected with a

food disposer, but not more than 20 Amps.

Electrical supply conductors shall be copper

and shall be minimum 16.” The dishwasher

should be properly grounded, positioned

as shown in Figure 9, and should be installed

by a qualified electrician. No other

appliances or outlets should be connected

to this circuit.

Openings fo elect ical lines must be

installed in the ma ked a eas as

shown in Figu es 8 and 9 to avoid

inte fe ence with the dishwashe

f ame o othe components.

Electrical Rating

Table 3

Figure 9

Hot water supply line Electric supply cable

Shut-off

valve

HWS 14”

(355 mm)

21”

(533 mm)

Figure 8

23-5/ ”-24-1/ ”

(600-613mm)

1-5/16

(49 mm)

3-1/2

(90 mm)

WARNING

THESE INSTALLATION

INSTRUCTIONS ARE

INTENDED FOR USE BY

QUALIFIED INSTALLERS

8 - ENGLISH www.gaggenau.com/us

PLACING THE DISHWASHER

Placing the Dishwasher

The profile strips on the sides of the

dishwasher allow the dishwasher to fit into

a cabinet opening with a width of 23-5/8”

(600 mm) to 24-1/8” (613 mm). Before

sliding the dishwasher into the cabinet

opening:

• Straighten the hot water supply line and

the electrical cable (see Figure 11).

• Level & Align (initial adjustments).

• Guide the drain hose carefully (avoiding

kinks in hose) as the dishwasher is slid

into the cabinet opening.

• Make final leveling adjustments (see

FINAL ADJUSTMENTS Section).

• To maintain the dishwasher position and

alignment, first determine which type

of mounting your dishwasher needs:

Top Mount is used for all types of

countertops that will not be damaged

by drilling.

• For a top mount, position the

brackets flat on each of the top

corners of the dishwasher as

shown in Figure 10A.

Side Mount is used when there is a

granite, marble or other hard natural

surface counter top that could be

damaged by drilling.

• For a side mount, bend the

brackets, then position them as

shown in Figure 10B.

• Drive Mounting Screws (see Figure 3)

through the holes in the brackets. See

Figure 10A or 10B.

• onnect the drain hose, hot water

supply line and electrical connections

as described in the following sections.

Figure 10

A. Mounting bracket

for mounting to under

countertop

B. Mounting bracket

bent for mounting to

side of cabinets

Figure 11

Level

IMPORTANT

If you wish to change the front panel of

the dishwasher this must be done before

sliding the dishwasher into place.

ENGLISH - 9

ENGLISH

www.gaggenau.com/us

DRAIN HOSE CONNECTION

Drain Hose

• Before beginning, turn off the water

supply!

• The access hole for the drain hose should

be 1.25” (32 mm) diameter.

• Use the hose clamps and rubber

connection hose (Figure 3) to connect

the drain hose to the sink, disposer or

air gap (Figure 14).

Figure 14

G, Fig 3

Drain Hose

Connected

to Sink

Be sure to follow your national

and local codes at all times.

Openings fo d ain lines must be

installed in the ma ked a eas as

shown in Figu es 8 and 9 to avoid

inte fe ence with the dishwashe

f ame o othe components.

Drain Hose

in Sink

with Air

Gap &

Disposer

Figure 13

min. 20” (500 mm)

clearance to floor

Air Gap

Rubber

Connector

Trap

disposer

Figure 12

Drain Hose

in Sink with

Air Gap/ No

Disposer

Air Gap

Rubber

Connector

Trap

min. 20” (500 mm)

clearance to floor

THESE INSTALLATION

INSTRUCTIONS ARE

INTENDED FOR USE BY

QUALIFIED INSTALLERS

Failure to provide t e proper drain

connection eig t, 20” (508mm)

above floor level wit ig loop or

air gap, will result in improper

draining of t e dis was er.

Improper draining may cause

damage to t e dis was er.

CAUTION

10 - ENGLISH www.gaggenau.com/us

HOT WATER CONNECTION

Openings fo wate lines must be

installed in the ma ked a eas as shown

in Figu es 8 and 9 to avoid

inte fe ence with the dishwashe

f ame o othe components.

• If using a solder joint instead of a com-

pression fitting, be sure to make all

solder connections before connecting

the water line to the dishwasher.

• Make sure there are no sharp bends or

kinks in the water line which might

restrict water flow.

• When connecting threaded pipe use pipe

thread compound or Teflon tape to seal

the connection.

• Before connecting the copper hot water

supply line to the dishwasher, it should

be flushed with hot water to clear any

foreign material.

• Apply Teflon tape or other pipe sealant

to 90° elbow fitting and connect

directly to water inlet valve (located at

the bottom front of the dishwasher)

• Turn on the water supply to check for

leaks after making connections.

Connecting the Hot Water

S pply Line

Figure 16

Figure 15

Shut off valve

(not included)

THESE INSTALLATION

INSTRUCTIONS ARE

INTENDED FOR USE BY

QUALIFIED INSTALLERS

DO NOT SOLDER WITHIN 6 IN HES

(152.4 MM) OF THE DISHWASHER’S

INLET VALVE.

TEMPERATURES REQUIRED FOR

SOLDERING WILL DAMAGE THE

VALVE!

CAUTION

* See Figure 15 and 16-water inlet

valve and 90° elbow

(located at the bottom front left-

hand side of the Dishwasher.)

Water

inlet

valve

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Lavavajillas de Gaggenau

Gaggenau

Gaggenau DF 250 Manual de usuario

Gaggenau

Gaggenau DF270101 Manual de usuario

Gaggenau

Gaggenau DF 261 Manual de usuario

Gaggenau

Gaggenau DF210500 Manual de usuario

Gaggenau

Gaggenau GM 230-110 Manual de usuario

Gaggenau

Gaggenau 400 Series Manual de usuario

Gaggenau

Gaggenau DI261 Manual de usuario

Gaggenau

Gaggenau DF481 Manual de usuario

Gaggenau

Gaggenau DF481500F Manual de usuario

Gaggenau

Gaggenau DF270101 Hoja de especificaciones

Gaggenau

Gaggenau DI260112CN Manual de usuario

Gaggenau

Gaggenau DI 230-130 Manual de usuario

Gaggenau

Gaggenau DF270 Manual de usuario

Gaggenau

Gaggenau DF210100 Manual de usuario

Gaggenau

Gaggenau DF 241-160 Manual de usuario

Gaggenau

Gaggenau 400 Series Manual de usuario

Gaggenau

Gaggenau DF250141 Manual de usuario

Gaggenau

Gaggenau DF480101 Manual de usuario

Gaggenau

Gaggenau DF 260 Manual de usuario

Gaggenau

Gaggenau DI 461 Manual de usuario

Gaggenau

Gaggenau DF 280 760 Manual de usuario

Gaggenau

Gaggenau DI 461 Manual de usuario

Gaggenau

Gaggenau DF460 Manual de usuario

Gaggenau

Gaggenau DF211701 Manual de usuario

Manuales populares de Lavavajillas de otras marcas

Electrolux

Electrolux ESI5211LOX Manual de usuario

KitchenAid

KitchenAid KUDB230B Manual de usuario

Brandt

Brandt BDJ424DB Manual de usuario

Asko

Asko DSD767UXXL.AU Manual de usuario

Beko

Beko DFN26210W Manual de usuario

NEFF

NEFF S153ITX00E Hoja de especificaciones

Midea

Midea SV 4.45 wi Manual de usuario

LG LDF7932 Manual de usuario

Gorenje

Gorenje GV63214 Manual de usuario

Hotpoint

Hotpoint HDA1100ZWH Manual de servicio

Blomberg

Blomberg LDFN2240W Manual de usuario

AEG

AEG FFB83836PM Manual de usuario

Cylinda

Cylinda DM3220RFD Manual de usuario

Atag

Atag DW8214MB Manual de usuario

GE GLD8000 Series Manual de usuario

Siemens

Siemens SN23HI02KE Hoja de especificaciones

Omega

Omega ODW717X Manual de usuario

BORETTI

BORETTI BVW-683 Manual de usuario