FUTABA T16IZ Manual técnico
YourFutabaT16IZtransmitterprogrammingcanbeupdatedeasily
online.Whenfunctionsareaddedorimproved,theupdatefile
canbedownloadedfromourwebsite.Copytheupdatefilestothe
microSDcardandthenusethefollowingproceduretoupdatethe
program.CheckourwebsitefortheFAQregardingupdatingformore
information.
HowtoupdateT16IZ
ŸƓƇƄƗƌƑƊŃƓƕƒƆƈƇƘƕƈ
Note: If the battery fully discharges during
program updating, updating will fail. When
the remaining battery capacity is 50% or
less, always recharge the battery before
updating.
Note: The model data in the transmitter can
be used unchanged after updating, but to
be safe, back up the model data before
updating.
1. Download the zip file of the update data
from our website.
([WUDFWWKH]LSÀOHRQ\RXUFRPSXWHU
3. The "FUTABA" folder will be created on your
computer.
4. Copy the "FUTABA" folder into your microSD
card.
Note: If the microSD card has already had
"another FUTABA" folder before you make a
copy, the "FUTABA" folder is OVERWRITTEN.
5. Insert the microSD card with "FUTABA" folder
that contained the update software into the
SD card slot on your T16IZ radio transmitter.
6. Turn on the transmitter power while pressing
down the "HOME/EXIT" button. The update
screen appears on the LCD display of your
T16IZ and the software update is started.
FutabaWEB
16IZUpdateZipfile
Download
Copythe"FUTABA"
folderintoyourSDcard.
InstalledmicroSDcard
oftheupdatefile
PresstheHOME/EXITswitchandturnon
Updating
1
2
7. When the software update is completed,
"Completed" message is shown on the LCD
display of your T16IZ. (Show below picture.)
8. Turn off the power switch of your T16IZ and
remove the microSD card from the card slot.
Possible Problems
When one of the error messages shown
below appears on the LCD screen your
T16IZ, the software update will not be
completed.
"Low battery."
Software update is postponed because
of low battery. Retry the software update
after the battery is recharged.
8SGDWHÀOHQRWIRXQG
The T16IZ cannot find the update file on
the microSD card. Check to be sure all the
update files have been copied onto the
microSD card.
%URNHQÀOH
7KH7,=GHWHFWVWKHXSGDWHÀOHHUURU7KH
update file may be broken or for another
transmitter.
"Write error."
The software update procedure is stopped
for an unknown reason. Contact your local
service center when this error message
appears on the LCD screen of your T16IZ.
Don't absolutely remove the battery
and the microSD card from the
transmitter during the update.
There is a possibility that the transmitter
will be damaged.
Recovering a failed update
If you failed to update for any reason, it
may transmitter will not start.
In that case, please update again
transmitter in the following procedure.
1. Detach the battery from the transmitter.
2. Insert the microSD card that contained
WKHXSGDWHÀOHVWRWKHWUDQVPLWWHU
3. Attach the battery to the transmitter
while pressing down the "HOME/EXIT"
button.
4. The update will start.
Even after the above steps, if the
transmitter fails to update or does not
start, please have it serviced.
Complete
1M23Z07709 T16IZ SOFTWARE UPDATE CHANGES
V3.1
V2
V3
1. Compatible with Futaba ESC MC-980H/A, MC-9130H/A, MC-9200H/A
Supports the telemetry function of MC-980H/A, MC-9130H/A, and MC-9200H/A.
1. Fixed telemetry voice for Futaba ESC and Hobbywing ESC.
2. Fixed the problem that model copy fails.
2. Hobbywing ESC telemetry compatible
Supports the telemetry function installed in some Hobbywing ESCs.
1. Add GYA553 Airplane Gyro setting function. (Refer the T16IZ GYA553 Setting Manual)
2. Compatible with SCORPION ESC telemetry
Added support for SCORPION POWER SYSTEM ESC some models.
◆Register the ESC with the transmitter. The registered ESC is displayed as "Futaba ESC".
◆The registered ESC is displayed as "Hobbywing ESC".
* The current and capacity consumption display may vary depending on the usage conditions, so use it as a guide.
◆ESC telemetry display screen
The ESC status is displayed. Alarm setting is also possible.
This software updates or alters the functions and features noted below. The instructions and information that follow are meant as a supplement to the original
instruction manual that accompanied the T16IZ transmitter. Please refer to the original instruction manual where applicable, but replace the steps indicated below with
these instructions. Please check to ensure that the update has been installed.
1) Select the System Menu.
2) Touch the [Information] button.
3) Confirm that the information in the display indicates the version numbers as noted above.
©FUTABA CORPORATION 2021, 06
3. GYA553 Addition of setting parameters
AIL / ELE / RUD holding power setting has been added to the setting parameters of GYA553.
Adjusted the gyro holding force of the aircraft in AVCS mode.
Decreasing the value weakens the holding power and makes
the operation feeling closer to the Normal mode.
For details on Hobbywing ESC telemetry
support, refer to the Hobbywing website.
*Only for sale in Japan
Otros manuales para T16IZ
8
Otros manuales de Mando a distancia de FUTABA
FUTABA
FUTABA T-FHSS Air-2.4GHz 10J Series Manual de usuario
FUTABA
FUTABA 2PL Manual del propietario
FUTABA
FUTABA 6EX 2.4GHZ Manual del propietario
FUTABA
FUTABA FP-S130 Manual de usuario
FUTABA
FUTABA F-14 Navy Manual de usuario
FUTABA
FUTABA T18SZ Manual de usuario
FUTABA
FUTABA FX-36 Instrucciones de montaje
FUTABA
FUTABA Mega Tech 3PK Manual de usuario
FUTABA
FUTABA T18SZ Manual de usuario
FUTABA
FUTABA 12Z Series Manual de usuario
FUTABA
FUTABA FASSTest-2.4GHz T16SZ Series Manual de usuario
FUTABA
FUTABA 2PC Manual de usuario
FUTABA
FUTABA 8FG Instrucciones de funcionamiento
FUTABA
FUTABA 2PL-2.4GHZ Manual de usuario
FUTABA
FUTABA T16IZ Manual de usuario
FUTABA
FUTABA T10PX Instrucciones de instalación
FUTABA
FUTABA 14MZ Manual de usuario
FUTABA
FUTABA 6EXAP Manual de usuario
FUTABA
FUTABA T16IZ Guía de instalación y uso
FUTABA
FUTABA 8FG Manual de usuario
