FUTABA 16IZ Manual de uso y cuidado

YourFutabaT16IZtransmitterprogrammingcanbeupdatedeasilyonline.Whenfunctionsareaddedorimproved,theupdatefilecanbedownloadedfromourwebsite.CopytheupdatefilestothemicroSDcardandthenusethefollowingproceduretoupdatetheprogram.CheckourwebsitefortheFAQregardingupdatingformoreinformation.HowtoupdateT16IZŸƓƇƄƗƌƑƊŃƓƕƒƆƈƇƘƕƈ

Note: If the battery fully discharges during

program updating, updating will fail. When

the remaining battery capacity is 50% or

less, always recharge the battery before

updating.

Note: The model data in the transmitter can

be used unchanged after updating, but to

be safe, back up the model data before

updating.

1. Download the zip file of the update data

from our website.

([WUDFWWKH]LSÀOHRQ\RXUFRPSXWHU

3. The "FUTABA" folder will be created on your

computer.

4. Copy the "FUTABA" folder into your microSD

card.

Note: If the microSD card has already had

"another FUTABA" folder before you make a

copy, the "FUTABA" folder is OVERWRITTEN.

5. Insert the microSD card with "FUTABA" folder

that contained the update software into the

SD card slot on your T16IZ radio transmitter.

6. Turn on the transmitter power while pressing

down the "HOME/EXIT" button. The update

screen appears on the LCD display of your

T16IZ and the software update is started.

FutabaWEB16IZUpdateZipﬁleDownloadCopythe"FUTABA"folderintoyourSDcard.InstalledmicroSDcardoftheupdateﬁlePresstheHOME/EXITswitchandturnonUpdating12

7. When the software update is completed,

"Completed" message is shown on the LCD

display of your T16IZ. (Show below picture.)

8. Turn off the power switch of your T16IZ and

remove the microSD card from the card slot.

Possible Problems

When one of the error messages shown

below appears on the LCD screen your

T16IZ, the software update will not be

completed.

"Low battery."

Software update is postponed because

of low battery. Retry the software update

after the battery is recharged.

8SGDWHÀOHQRWIRXQG

The T16IZ cannot find the update file on

the microSD card. Check to be sure all the

update files have been copied onto the

microSD card.

%URNHQÀOH

7KH7,=GHWHFWVWKHXSGDWHÀOHHUURU7KH

update file may be broken or for another

transmitter.

"Write error."

The software update procedure is stopped

for an unknown reason. Contact your local

service center when this error message

appears on the LCD screen of your T16IZ.

Don't absolutely remove the battery

and the microSD ca r d f r o m t h e

transmitter during the update.

There is a possibility that the transmitter

will be damaged.

Recovering a failed update

If you failed to update for any reason, it

may transmitter will not start.

In t hat case, please update again

transmitter in the following procedure.

1. Detach the battery from the transmitter.

2. Insert the microSD card that contained

WKHXSGDWHÀOHVWRWKHWUDQVPLWWHU

3. Attach the battery to the transmitter

while pressing down the "HOME/EXIT"

button.

4. The update will start.

Even af t e r t h e above s t e p s , if the

transmitter fails to update or does not

start, please have it serviced.

Complete

1M23Z07711T16IZSOFTWAREUPDATECHANGESV3.2V3V3.11. Compatible with Futaba ESC MC-980H/A, MC-9130H/A, MC-9200H/A

Supports the telemetry function of MC-980H/A, MC-9130H/A, and MC-9200H/A.

1. Fixed an issue where the Vario Melody settings were not saved.

1. Fixed telemetry voice for Futaba ESC and Hobbywing ESC.

2. Fixed the problem that model copy fails.

This software updates or alters the functions and features noted below. The instructions and information that follow are meant as a supplement to the original

instruction manual that accompanied the T16IZ transmitter. Please refer to the original instruction manual where applicable, but replace the steps indicated below with

these instructions. Please check to ensure that the update has been installed.

1) Select the System Menu.

2) Touch the [Information] button.

3) Conﬁrm that the information in the display indicates the version numbers as noted above.

◆RegistertheESCwithtransmitter.◆Alternatively,select[FutabaESC]instartslot24.◆TheregisteredESCwillbedisplayedas"FutabaESC".ConnectSBM-2totheS.I/Fportonthebackoftransmitter.◆Linkagemenu→Sensor→3/3Registrationtotransmitter●Callpage3of[Sensor].*Pleasenotethattheproperdefaultslotforthisaccessoryisnumber8(8-15).Thissensoruseseightslots.Beingmadetoastartslotare8,16,and24.Informationonhowtochangetheslotassignmentisincludedinthetransmitter'smanual.ConnecttheSBM-2tothetransmitterasshown,thentapRegister.CompleteregistrationandremoveSBM-2fromthetransmitter.◆The registered Hobbywing ESC is displayed as "Hobbywing ESC".

For details on Hobbywing ESC telemetry

support, refer to the Hobbywing website.

AlarmischosenfromBuzzer,Voice,andInhibit.AllowsSpeechtobeturnedONorOFF.↑Anupwardarrowindicatesthealarmwillsoundwhenthecurrentreachesaboveyoursetvalue.↓Adownwardarrowindicatesthealarmwillsoundwhenthecurrentreachesbelowyoursetvalue.*The current and capacity consumption display may vary

depending on the usage conditions, so use it as a guide.

◆ESC telemetry display screen

The ESC status is displayed. Alarm setting is also possible.

Displaymax/minvaluePressandholdtoreset.Displaymax/minvaluePressandholdtoreset.Taptomovetothecurrentsettingpage.Taptomovetothevoltagesettingpage.Taptomovetothecapacitysettingpage.Taptomovetotherotationsettingpage.Enterthenumberofpolesforyourmotor.Whenenabled,thealarmwillbeactivatedinthefollowingwarningstate.Ifthegearisdown,enterthegearratiotodisplaythehelicopterrotorspeedandtheairplanegeardownpropellerspeed.Whenenabled,thevibratorwillstartinthefollowingwarningstate.◆Warningstate◆AlarmscanbesetforVoltage,Capacity,Rotation,ESCtemperature,andThrottleusingthesameprocedure.ShowstheoutputlevelfromtheESCtothemotor,notthepositionofthethrottlestick.Evenifthestickisinthe50%position,theoutputmaynotbe50%dependingontheESCsetting.Throttlenotat0%LowvoltageOvertemperatureOvercurrentMotorlockedThrottlesignallostWhenthethrottlestickisnotlowwhenESCisstartedWhenthebatteryvoltageisbelowthecutoﬀvoltageWhentheESCtemperatureis110°CorhigherPeakcurrentoverWhenthemotorlocksWhennothrottlesignalisreceivedformorethan0.25sTaptomovetothetemperaturesettingpage.Taptomovetothethrottlesettingpage.◆MC-9130H/AtelemetryconnectionexampleSBM-2ESCToCH3TofreeportTodrivebatteryThrottleToS.BUS2◆AlarmsettingSetsthecurrentonwhichthealarmoperates.

V21. Add GYA553 Airplane Gyro setting function. (Refer the T16IZ GYA553 Setting Manual)

2. Compatible with SCORPION ESC telemetry

Added support for SCORPION POWER SYSTEM ESC some models.

©FUTABA CORPORATION 2021, 12

2. GYA553 Addition of setting parameters

AIL / ELE / RUD holding power setting has been added to the setting parameters of GYA553.

Adjusted the gyro holding force of the aircraft in AVCS mode.

Decreasing the value weakens the holding power and makes

the operation feeling closer to the Normal mode.

Tabla de contenidos

Otros manuales de Mando a distancia de FUTABA

FUTABA

FUTABA 8FG Instrucciones de funcionamiento

FUTABA

FUTABA T8J FUT01004369-3 Manual de usuario

FUTABA

FUTABA T10PX Instrucciones de instalación

FUTABA

FUTABA 8FG Manual de usuario

FUTABA

FUTABA FP-8JN Manual de usuario

FUTABA

FUTABA FP-8SGAP Manual de usuario

FUTABA

FUTABA FP-G132 Manual de usuario

FUTABA

FUTABA T16IZ Manual de usuario

FUTABA

FUTABA T16IZ Ver.2 Manual

FUTABA

FUTABA T18SZ Manual de usuario

FUTABA

FUTABA FX-20 Manual de usuario

FUTABA

FUTABA 14SG Manual de usuario

FUTABA

FUTABA 9VAP Manual de usuario

FUTABA

FUTABA T18MZ Manual de usuario

FUTABA

FUTABA FDLS-1 Manual de usuario

FUTABA

FUTABA 10C Manual de usuario

FUTABA

FUTABA FP-2E Manual de usuario

FUTABA

FUTABA 14SG Manual de usuario

FUTABA

FUTABA ATTACK Manual de usuario

FUTABA

FUTABA 3PM-FS Manual de usuario

FUTABA

FUTABA T10PX Cómo utilizar

FUTABA

FUTABA R7108SB Instrucciones de instalación

FUTABA

FUTABA SKYSPORT 2FR Manual de usuario

FUTABA

FUTABA 9 CHP SUPER Manual de usuario

Manuales populares de Mando a distancia de otras marcas

Panasonic

Panasonic EUR7622KB0 Manual de usuario

Bang & Olufsen

Bang & Olufsen Beo4 Manual de usuario

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manual de usuario

Multiplex

Multiplex PROFI TX 9 Manual de usuario

One Remote

One Remote RMB4 Manual de usuario

HR Matic

HR Matic HR MULTI 3 Manual de usuario

Yamaha

Yamaha ACC-GNRST-30-20 Manual de usuario

EisSound

EisSound KBSOUND Manual de usuario

Marantz

Marantz RC101 Manual de usuario

Conrad

Conrad FS20 TC6 Manual de usuario

Anritsu

Anritsu MP1777A Manual de usuario

Niles

Niles WVC100 Guía de solución de problemas

RCA

RCA RCU1300 Manual de usuario

Bang & Olufsen

Bang & Olufsen BEO6 Manual de usuario

GE 94901 Manual de usuario

Onbon

Onbon YQ1-75 Manual de usuario

Invacare

Invacare G91S Manual de usuario

JR Racing

JR Racing XR2 Manual de usuario