Full Boar FBT-0500 Manual de usuario

KNOW YOUR PRODUCT

WARNING: Read all safety warnings and all instructions. Failure to follow the

warnings and instructions may result in electric shock, ﬁre and/or serious injury.

Save all warnings and instructions for future reference.

09/15

ROTARY HAMMER

DRILL KIT

•5jOULES

•1250w

INSTRUCTIONMANUAL

Voltage: 230-240V ~50Hz

Power: 1250W

Impact Power: 5.0J

Impact Rate: 0-4,100/min¹

No Load Speed: 0-850min¹

Accessory Fitment: SDS+

Drilling Capacity: 32mm

Weight: 7.8kg

SPECIFICATIONS - MODEL NO. FBT-0500

KNOW YOUR PRODUCT

1. SDS+ Accessory Holder

2. Accessory Locking Sleeve

3. Depth Rod Locking Dial

4. Side Mode Selector

5. Grease Cap

6. Rear Mode Selector

7. On/Off Trigger

8. Pressure Indicator

9. Soft Grip Rear Handle

10. Service Indicator LED

11. Side Handle

12. 250mm x 24mm Flat Chisel Bit

13. Depth Rod

14. Dust Cover

2345

1112

SPECIFICATIONS....................................................... Page 02

KNOW YOUR PRODUCT........................................... Page 02

INTRODUCTION........................................................ Page 04

SAFETY INSTRUCTIONS........................................... Page 04

SET-UP........................................................................ Page 08

CHOOSING AN OPERATION MODE....................... Page 09

OPERATION............................................................... Page 10

MAINTENANCE......................................................... Page 11

TROUBLE SHOOTING .............................................. Page 12

DESCRIPTION OF SYMBOLS.....................................Page 13

CONTENTS................................................................ Page 14

WARRANTY................................................................ Page 16

TABLE OF CONTENTS

Congratulations on purchasing a Full Boar Rotary Hammer.

Your Full Boar Rotary Hammer Drill Kit FBT-0500 has been

designed to rapidly drill, chip, chisel and break masonry

products such as concrete.

Read and understand the Owner’s Manual before operating

the generator. Failure to do so could result in personal injury

or equipment damage.

INTRODUCTION

WARNING! When using mains-powered tools, basic safety precautions, including the

following, should always be followed to reduce risk of ﬁre, electric shock, personal injury

and material damage.

Read the whole manual carefully and make sure you know how to switch the tool off in an emergency,

before operating the tool. Save these instructions and other documents supplied with this tool for

future reference. The manufacturer cannot accept any liability for damage or accidents which arise

due to a failure to follow these instructions and the safety information.

This product has been designed for 230V and 240V only. Always check that the power

supply corresponds to the voltage on the rating plate. Note: The supply of 230V and 240V is

interchangeable for Australia and New Zealand.

This tool is double insulated in accordance with AS/NZS 60745-1;

therefore no earth wire is required.

The power supply for this product should be protected by a residual current device (rated at 30mA or

less). A residual current device reduces the risk of electric shock.

If the supply cord of this power tool is damaged, it must be replaced by a specially prepared cord

available through the service organization.

Note: Double insulation does not take the place of normal safety precautions when operating this

tool. The insulation system is for added protection against injury resulting from a possible electrical

insulation failure

within the tool.

Using an Extension Lead

Always use an approved extension lead suitable for the power input of this tool. Before use, inspect

the extension lead for signs of damage, wear and ageing. Replace the extension lead if damaged or

defective.

When using an extension lead on a reel, always unwind the lead completely. Use of an extension lead

not suitable for the power input of the tool or which is damaged or defective may result in a risk of ﬁre

and electric shock.

ELECTRICAL SAFETY

GENERAL SAFETY INSTRUCTIONS

WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and

instructions may result in electric shock, ﬁre and/or serious injury.

Save all warnings and instructions for future reference. The term “power tool” in the warnings

refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

1. Work area safety

a. Keep work area clean and well lit. Cluttered or dark areas invite accidents.

b. Do not operate power tools in explosive atmospheres, such as in the presence of ﬂammable

liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.

c. Keep children and bystanders away while operating a power tool. Distractions can cause you

to lose control.

2. Electrical safety

a. Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power tools. Unmodiﬁed plugs and matching outlets

will reduce risk of electric shock.

b. Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.

c. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase

the risk of electric shock.

d. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power

tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled

cords increase the risk of electric shock.

e. When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use

of a cord suitable for outdoor use reduces the risk of electric shock.

f. If operating a power tool in a damp location is unavoidable, use a residual current device

(RCD) protected supply. Use of an RCD reduces the risk of electric shock.

3. Personal safety

a. Stay alert, watch what you are doing and use common sense when operating a power tool.

Do not use a power tool while you are tired or under the inﬂuence of drugs, alcohol or

medication. A moment of inattention while operating power tools may result in serious personal

injury.

b. Use personal protective equipment. Always wear eye protection. Protective equipment

such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate

conditions will reduce personal injuries.

c. Prevent unintentional starting. Ensure the switch is in the off-position before connecting to

power source and/or battery pack, picking up or carrying the tool. Carrying power tools with

your ﬁnger on the switch or energising power tools that have the switch on invites accidents.

d. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may result in personal injury.

e. Do not overreach. Keep proper footing and balance at all times. This enables better control of

the power tool in unexpected situations.

f. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves

away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.

g. If devices are provided for the connection of dust extraction and collection facilities, ensure

these are connected and properly used. Use of dust collection can reduce dust-related hazards.

4. Power tool use and care

a. Do not force the power tool. Use the correct power tool for your application. The correct

power tool will do the job better and safer at the rate for which it was designed.

b. Do not use the power tool if the switch does not turn it on and off. Any power tool that

cannot be controlled with the switch is dangerous and must be repaired.

– Wear ear protectors. Exposure to noise can cause hearing loss.

– Use auxiliary handle(s), if supplied with the tool. Loss of control can cause personal injury.

– Hold power tool by insulated gripping surfaces, when performing an operation where the

cutting accessory may contact hidden wiring or its own cord. Cutting accessory contacting a “live”

wire may make exposed metal parts of the power tool “live” and could give the operator an electric

shock.

WARNING! This appliance is not intended for use by persons (including children) with

reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless

they have been given supervision or instruction concerning use of the appliance by a person

responsible for their safety.

Recommendations for the use of a residual current device with a rated residual current of 30mA or

less.

Using an Extension Lead

• Alwaysuseanapprovedextensionleadsuitableforthepowerinputofthistool.Beforeuse,inspect

the extension lead for signs of damage, wear and ageing. Replace the extension lead if damaged or

defective.

• Whenusinganextensionleadonareel,alwaysunwindtheleadcompletely.Useofanextension

lead not suitable for the power input of the tool or which is damaged or defective may result in a risk

of ﬁre and electric shock.

• Itisrecommendedthattheextensionleadisamaximumof25minlength.DoNotusemultiple

extension leads.

• Beforedrillingintowalls,ceilingsetc,ensuretherearenoconcealedpowercablesorpipesinthe

cavity.

• Alwaysusethesidehandle,thisgivesyougreatercontroliftheaccessoryshouldbecomejammed.

• Keepthecordclearoftheaccessorybeingused,donotwrapthecordaroundyourarmorwrist.

• Holdthetoolbytheinsulatedgrippingsurfaceswhenperforminganoperationwheretheaccessory

may contact hidden wiring or its own cord.

GENERAL POWER TOOL SAFETY WARNINGS

c. Disconnect the plug from the power source and/or the battery pack from the power tool

before making any adjustments, changing accessories, or storing power tools. Such preventive

safety measures reduce the risk of starting the power tool accidentally.

d. Store idle power tools out of the reach of children and do not allow persons unfamiliar with

the power tool or these instructions to operate the power tool. Power tools are dangerous in

the hands of untrained users.

e. Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts

and any other condition that may affect the power tool’s operation. If damaged, have the

power tool repaired before use. Many accidents are caused by poorly maintained power tools.

f. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges

are less likely to bind and are easier to control.

g. Use the power tool, accessories and tool bits etc. in accordance with these instructions,

taking into account the working conditions and the work to be performed. Use of the power

tool for operations different from those intended could result in a hazardous situation.

5. Service

a. Have your power tool serviced by a qualiﬁed repair person using only identical replacement

parts. This will ensure that the safety of the power tool is maintained.

ROTARY HAMMER DRILL SAFETY WARNINGS

• Usethickcushionedglovesandlimittheexposuretimebytakingfrequentbreaks.

• Vibrationcausedbythehammeractionmaybeharmfultoyourhandsandarms.

• Whenremovinganaccessoryfromthetoolavoidcontactwithskinanduseproperprotective

gloves when grasping the bit or accessory. Accessories may be hot after prolonged use.

WARNING! Some dust created by power sanding, sawing, grinding, drilling and other

construction activities contain chemicals known to cause cancer, birth defects or other reproductive

harm.

Some examples of these chemicals are:

• Leadfromlead-basedpaints;

• Crystallinesilicafrombricks,cementandothermasonryproducts,and;

• Arsenicandchromiumfromchemically-treatedtimber.

The risk from such exposures vary depending on how often you do this type of work. To reduce

your exposure to these chemicals; work in a well ventilated area, and work with approved safety

equipment, such as those dust masks that are speciﬁcally designed to ﬁlter out microscopic particles.

Always wear eye protection and a dust mask for dusty applications and when drilling/chiselling

overhead. Sanding particles can be absorbed by your eyes and inhaled easily and may cause health

complications.

Special requirements:

• Wearearprotectors.Exposuretonoisecancausehearingloss.

• Useauxiliaryhandlessuppliedwiththetool.Lossofcontrolcancausepersonalinjury.

ROTARY HAMMER DRILL SAFETY WARNINGS

SET-UP & PREPARATION

WARNING! Ensure the tool is turned off and disconnected from the power supply before

performing any of the following operations.

Using the Depth Rod

The Full Boar FBT-0500 comes with a depth rod that allows you

to drill to a pre-determined depth.

1. Loosen the depth rod securing nut then insert the depth

rod (Fig. 1).

2. Adjust the depth rod so the drill bit extends beyond the end

of the depth rod to the required drilling depth (Fig. 2).

3. Tighten the depth rod securing nut to lock the depth rod

into place.

4. Drill the hole until the end of the depth rod touches the

workpiece.

Fitting SDS+ Accessories

1. Prior to insertion into the chuck, remove any dust and

debris from the SDS+ accessory, then apply some lubricant

to the end of the accessory.

2. Pull and hold the locking sleeve back. Insert the SDS+

accessory (Fig. 3).

3. Rotate the accessory and continue to insert as far as possible

into the chuck. Release the locking sleeve

4. Check the SDS+ accessory is properly secured in the chuck

by pulling on the accessory. Note: It should have approx.

10-20mm of movement. This is normal. (Fig. 1).

5. To remove the SDS+ accessory, pull back the locking sleeve and then pull the accessory

out of the chuck.

Fitting the Dust Cover

The dust cover catches dust and debris while using the drill in an upright or overhead

positon, helping to avoid dust entering the air vents.

1. Slide the dust cover over the accessory to be ﬁtted (Fig. 4).

Add lubrication to the end of accessory before inserting into

the SDS+ chuck.

2. Pull back the accessory locking sleeve and insert the

accessory. Release the locking sleeve.

3. Press the dust cover into the end of the locking sleeve.

Required Drilling

Depth

Fig. 1

Fig. 2

Fig. 3

Fig. 4

CHOOSING AN OPERATION MODE

The Full Boar FBT-0500 has 4 different operating modes: drilling, hammer drilling, chiselling

with ﬁxation and chiselling without ﬁxation. Follow the below instructions to select your

desired mode of operation.

Hammer Drilling

Rotate the side mode selector to the

drill icon, and rotate the rear mode

selector to the hammer icon. This

setting is recommended for use when

drilling holes in concrete and other

masonry products. The hammer

action will be in operation while

simultaneously the drill bit rotates.

Chiselling (free rotation)

Rotate the side mode selector to the

free rotation chiselling mode & rotate the

rear mode selector to the hammer icon.

This setting is helpful when you want to

have the chisel in a particular position.

The bit will stop rotating once contact is

made with the material, or you can rotate

the bit by hand. Once you have found

the ideal position, you can change to

chiselling (locked) for continual use.

Drilling

Rotate the side mode selector to the

drill icon, and rotate the rear mode

selector to the no hammer icon.

This setting is recommended for use

when you desire the accessory to

rotate without hammer action. Ideal

for drilling into timber or steel when

correct accessories for such materials

are used.

Side Mode

Selector

Rear Mode

Selector

Chiselling (locked)

Rotate the side mode selector to the

chisel icon, and rotate the rear mode

selector to the hammer icon. This

setting is recommended for use when

you desire a hammer action without

the accessory rotating which is ideal

for “chiseling or chipping” away at

masonry products, pick or chisel

accessory bits should be used.

1. Ensure your workpiece is securely clamped where possible.

2. Connect the tool to the mains power supply. The ready for

use indicator LED will illuminate when the tool is connected

to power and ready for use (Fig. 5).

3. Select the desired mode of operation (refer to Choosing an

Operation Mode section of manual).

4. Hold the rotary hammer drill to the work surface. Apply

enough pressure on the rear handle so that the press control

indicator on the side of the housing goes green (Fig. 6). The

rotary hammer drill will work most effieciently in this position.

If you apply excessive pressure the indictor will go red. This

guide prevents overloading of the tool.

5. Squeeze the on/off trigger to start drilling (Fig. 7). Release

the trigger to stop drilling.

NOTE: Prior to changing modes, the on/off switch should be

released and the drill should have come to a complete stop.

OPERATION

Fig. 5

Fig. 6

Fig. 7

Tabla de contenidos

Manuales populares de Taladro percutor rotativo de otras marcas

Ozito

Ozito 1500W Manual de usuario

AEG

AEG KH 26 E Manual de usuario