FULGOR F7PBM36S1-L Manual de usuario
F7PBM36S1 - L
F7PBM36S1 - R
F7IBM36O1 - L
F7IBM36O1 - R
F7IBW24O1 - L
F7IBW24O1 - R
F7PBW24S1 - L
F7PBW24S1 - R
EN INSTALLATION GUIDE
FR NOTICE D’INSTALLATION
ES GUÍA DE INSTALACIÓN
FRIDGE
RÉFRIGÉRATEUR
REFRIGERADOR
EN
1
TABLE OF CONTENTS PAGE
1. Important Instructions 2
1.1 Important safety instructions 2
1.2 Children safety 2
2. Technical Requirements 3
2.1 Appliance features and installation
requirements 3
2.2 Installation niche features: Professional
Built-In Series 4
2.3 Installation niche features: Professional
Series 5
3. Preparing The Installation 6
3.1 Transport to installation site and
unpacking 6
3.2 Electrical and Water connection 6
3.3 Energy: Alternatives and Home
Automation 7
3.4 Levelling 8
4. Niche Dimensions 9
4.1 Niche Dimensions and Installation Styles:
Professional Built-In Series 9
4.2 Flush installation with standard aluminum
trims 9
4.3 Prominent installation with standard
aluminum trims 9
TABLE OF CONTENTS PAGE
5. Panels Mounting 10
5.1 Decorative door and Bottom-Drawer
panels layout 10
5.2 Decorative panels layout for Fridge with
one Bottom-Drawer 12
5.3 Decorative panels layout for Fridge with
Glass door and one Bottom-Drawer 13
5.4 Panels Dimensions Single Bottom
- Drawer 14
5.5 Mounting the handles 15
5.6 drawer 16
6. Installation 18
6.1 Built-in installation single appliance 18
6.2 Built-in installation two or more
appliances 19
6.3 Maximum cabinet depth over
“Integrated” refrigerator with single door
panel 21
7. 7. Completing The Installation 22
7.1 Anti-tipping safety assembly 22
7.2 Mounting the handles on stainless front 23
7.3 Ventilation 23
7.4 Post installation checklist 24
7.5 Start up 24
EN
2
1 - Important Instructions
1.1 Important safety instructions
Symbols used in the Guide:
NOTE
Tips for the correct use of the appliance
IMPORTANT
Directions to avoid appliance damage
WARNING
Directions to prevent injury
1.2 Children safety
DANGER: Risk of child entrapment. Before you throw away
your old refrigerator or freezer:
• Take off the doors
• Leave the shelves in place so that children may not easily
climb inside.
IMPORTANT
Dimensions in parentheses are in inches.
Weights in parentheses are in pounds.
Temperatures in parentheses are in Fahrenheit degrees.
EN
3
2.1 Appliance features and installation
requirements
Appliance dimensions Professional Built-In Series
Series 24” w: 599 mm (23 5/8”)
h: 2120 mm (83 1/2”)
d: 610 mm ( 24”)
Series 36” w: 899 mm (35 3/8”)
h: 2120 mm (83 1/2”)
d: 610 mm ( 24”)
Appliance dimensions Professional Series
Series 24” w: 599 mm (23 5/8”)
h: 2120 mm (83 1/2”)
d: 635 mm ( 25”)
Series 36” w: 899 mm (35 3/8”)
h: 2120 mm (83 1/2”)
d: 635 mm ( 25”)
Packaging dimensions
Series 24” w: 650 mm (25 5/8”)
h: 2260 mm ( 89”)
d: 800 mm (31 1/2”)
Series 36” w: 950 mm (37 3/8”)
h: 2260 mm
( 89”)
d: 800 mm
(31 1/2”)
Weight with packaging
Series 24” up to 230 kg (507 lb)
Series 36” up to 295 kg (650 lb)
Voltage AC 110 - 120V 60Hz
Power supply cable 90° Nema 5-15P
Potable water supply
pressure from 0.05 MPa to 0.5 MPa
(0.5 Bar - 5 Bar)
Water connection 3/4” NPT (1/4” elbow
adapter included)
Provided installation
accessories - Customized panels mounting
Kit (if applicable)
- Anti-tipping Kit
- Lateral connecting kit
- 4 mm (1/8”) allen wrench
Additional equipment
necessary - Phillips head screwdriver
- wood drill
- 2.5 mm (1/8”) bit for wood
- 8 mm (3/8”) bit for walls
- 17 mm (11/16”) wrench
- 19 mm (3/4”) wrench
2. Technical Requirements
EN
4
2.2 Installation niche features: Professional
Built-In Series
A- area to be left clear for the anti-tipping brackets
Minimum Niche Height
2134 mm (84”)
Minimum Niche Width
36”: 902 mm (35 1/2”)
24”: 602 mm (23 3/4”)
Minimum Niche Depth
610 mm (24”) + panel thickness for flush install
Door Swing Clearance
36”: 1470 mm (57 7/8”)
24”: 1170 mm (46”)
Door Opening Angle
105°
Width
36”: 899 mm (35 3/8”)
36”: 599 mm (23 5/8”)
Height
2120 mm (83 1/2”) + 25 mm (1”)
Depth with door (without panel)
610 mm (24”)
Minimum distance from the wall (hinge side)
36”: 160 mm (6 1/4”)
24”: 90 mm (3 1/2”)
105°
560 (22”)
610 (24”)
36: 899 (35 ⅜”)
24: 599 (23 ⅝”)
10 (⅜”)
992 (39”)
36: 1470 (57 ⅞”)
24: 1170 (46”)
36: 160 (6 ¼”)
24: 90 (3 ½”)
A A
140 (5 ½”) 140 (5 ½”)
100 (4”)
100 (4”)
min 2064 (84”)
36”: 902 (35 ½”)
24”: 602 (23 ¾”)
610 (24”)
560 (22”)
1293 (50 ⅞” )
474
(18 ⅝”)
231 (9
⅛”
) +
25 (1”)
500 (19 ¾”)
248 (9
¾”
)
+ 25 (1”)
20 (¾”)
721 (28 ⅜”) +25 (1”)
2120 (83 ½”) +25 (1”)
EN
5
2.3 Installation niche features: Professional
Series
A- area to be left clear for the anti-tipping brackets
Minimum Niche Height
2134 mm (84”)
Minimum Niche Width
36”: 902 mm (35 1/2”)
24”: 602 mm (23 3/4”)
Door Swing Clearance
36”: 1470 mm (57 7/8”)
24”: 1170 mm (46”)
Door Opening Angle
105°
Width
36”: 899 mm (35 3/8”)
24”: 599 mm (23 5/8”)
Height
2120 mm (83 1/2”) + 25 mm (1”)
Depth with door
635 mm (25 ”)
Minimum distance from the wall (hinge side)
36”: 230 mm (9”)
24”: 160 mm (6 1/4”)
IMPORTANT
If the units are to be installed inside a niche or within an
enclosed structure, it is necessary to design a ventilation
shaft at the back of the niche to assure proper ventilation
at the back of the unit.
Cross-sectional chimney ventilation area should equal
200cm² (31in²)
1016 (40”)
36: 1470 (57 ⅞”)
24: 1170 (46”)
560 (22”)
75 (3”)
36: 899 (35 ⅝”)
30: 749 (29 ½”)
24: 599 (23 ⅝”)
10 (⅜”)
58 (2 ¼”)
105°
635 (25”)
36: 230 (9”)
24: 160 (6 ¼”)
A A
140 (5 ½”) 140 (5 ½”)
100 (4”)
100 (4”)
min 2134 (84”)
36: 902 (35 ½”)
24: 602 (23 ¾”)
560 (22”)
2120 (83 ½”) +25 (1”)
613 (24 ⅛”)+25 (1”)
635 (25”)
693 (27 ¼”)
516 (20 ⅜”) 1296 (50”)
195 (7 ⅝”)
8 (⅜”) 8 (⅜”)
97 (3 ⅞”)
+ 25 (1”)
min 10 (⅜”)
min 50 (2”)
EN
6
3.1 Transport to installation site and unpacking
WARNING
The appliance is very heavy.
Take maximum care during handling to avoid injury.
IMPORTANT
The appliance should always be transported in an erect
position.
Avoid at all costs leaning it on its front side.
1
4
1
2
3
Since this is a large and heavy appliance, before
transporting the appliance, check the access to the location
where it will be installed (door size, manoeuvring space in
stairwells, etc.).
The appliance is attached to the base of the packaging
(pallet) through four bolts which can be removed using a 19
mm (3/4”) wrench.
It is recommended to use a manual transporting device to
move the appliance to the installation site, and only at this
point to remove the base of the packaging.
The appliance should always be transported in an erect
position.
If this is not possible, transport the appliance laying on its
rear side.
Once at the installation site, the appliance, which is
equipped with four wheels, can be taken off the pallet and
positioned in the installation area.
Operate as follows:
• Take off the four bolts securing [ 1 ] the appliance to the
pallet by means of a 19 mm (3/4”) wrench or socket.
• Remove the fixing brackets [ 3 ] and [ 4 ].
• To release the front fixing bracket [ 3 ], unscrew the rear
wheel adjusting bolt [ 2 ] by means of a 13 mm (1/2”)
wrench or socket. Avoid straining this bolt at its stop
points one way or the other so as to not damage the rear
leveling system.
Ensure the front leveling legs are retracted so that
all 4 wheels are able to contact the floor for easiest
maneuvering.
• From the back of the unit and by means of a suitable,
high duty hand trolley, take off the appliance and place
it on the floor.
Be very careful to avoid any damage to floors. Delicate
floors should be protected with plywood, hard cardboard
or similar material panels.
3.2 Electrical and Water connection
NOTE
The Built-in filter cannot make it safe to drink any water
which is not already suitable for human consumption.
WARNING
The appliance should be connected only to a potable
water supply system.
IMPORTANT
Do not use extension cords or adapters.
Once the appliance is fully installed, connected to the
water supply (if applicable) and operational, in the event
that the water supply must be turned off, touch the button
on control panel to disable the ice maker before the
main water is shut off to prevent the appliance from
entering a ‘NO WATER IN’ alarm state.
EW
E W
EW
E W
The appliances are delivered from the factory for operation
at 110V-120V AC - 60Hz (US and Canada).
They are provided with a suitable supply cable and plug to
be connected to an appropriate 15A socket providing an
effective grounding.
A dedicated 15A circuit breaker should also be installed and
should be easily accessible so that it can be easily switched
off before performing any installation or maintenance.
3. Preparing The Installation
EN
7
To connect to the water supply system (for appliances
equipped with ice makers) a 1/4” waterline with accessible
shut-off valve must be supplied.
The appliance is provided with a water adapter elbow
which is suitable for the recommended water pressure and
complies the applicable food and water regulations.
The water filter cartridge, which is provided with
the appliance, should be installed according to the
accompanying instructions. The solenoid connection on the
appliance is 3/4” diameter but is metric threaded (NPT).
A standard garden hose threaded connector such as a
braided stainless hose found at typical hardware stores will
strip or damage the solenoid threads. It is recommended to
use only the supplied 1/4” quick connect elbow adapter
for connecting a 1/4” copper or polyethylene source water
line to the appliance.
IMPORTANT
Do not use extension cords and/or multiple adapters for
the power supply connection.
ELECTRICAL AND WATER SUPPLY BEHIND THE UNIT
Professional Built-In Series Professional Series
E
W
E
W
3.3 Energy: Alternatives and Home Automation
If energy is supplied through an alternative energy power
source (solar, geothermal, etc..) or if home automation
systems are installed with carrier signals in the power
lines, it may be necessary to install an isolation transformer
(not supplied) to prevent interference with the appliance’s
electronics.
Professional Built-In Series:
FIG.1 - BACK OF APPLIANCE
Water connection
Electrical connection
Operate as follows:
• Unwind the electric cable and connect it directly to the
wall socket.
• Make sure the appliance is in the Stand-by condition and
that all lights are off; should it be not so press the Unit
button to switch it off.
FIG.1
1
EN
8
Professional Series:
FIG.2 - BACK OF APPLIANCE
Electrical connection
Water connection
Operate as follows:
• Unwind the electric cable and connect it directly to the
wall socket.
• Make sure the appliance is in the Stand-by condition and
that all ights are off; should it be not so press the Unit
button to switch it off.
FIG.3 - FRONT OF APPLIANCE
1
• Firmly tighten with fingers - a tool / wrench should not
be needed to make a proper seal. Turn on the water and
ensure all connections are not leaking prior to pushing
the unit into the niche.
3.4 Levelling
Adjust the appliance level by means of the front levelling
feet and the rear adjustable wheels
1
2
1
2
Operate as follows:
• If necessary, remove the bottom plinth or grille (it is kept
in position by magnets), adjust the height of the levelling
feet [ 1 ] by means of a 17 mm (11/16”) wrench.
• Then adjust the height of the rear wheels by turning the
front adjusting bolts [ 2 ] clockwise (raise) or counter-
clockwise as it may be required.
Take care if using a power driver for this and lower the
clutch to prevent damaging the leveling mechanism.
• Remount the bottom plinth or grille.
Este manual sirve para los siguientes modelos
7
Tabla de contenidos
Idiomas:
Otros manuales de Refrigerador de FULGOR
FULGOR
FULGOR F7PBM36S2 Manual de usuario
FULGOR
FULGOR SOFIA PRO F7IRC36O1 Manual de usuario
FULGOR
FULGOR FBFD 351 NF ED Manual de usuario
FULGOR
FULGOR SOFIA PRO F7IRC30O1 Manual de usuario
FULGOR
FULGOR SOFIA PRO F7SRC36S1 Manual de usuario
FULGOR
FULGOR FBCD 761 TNF EDBL Manual de usuario
FULGOR
FULGOR FM36CDFDS1 Manual de usuario
