Fujitsu MAB3091FC Series Manual de usuario
C141-F028-01EN
MAA3182FC SERIES
MAB3091FC, MAB3045FC SERIES
MAC3091FC, MAC3045FC SERIES
DISK DRIVES
FIBRE CHANNEL INTERFACE
MAINTENANCE MANUAL
C141-F028-01EN i
REVISION RECORD
Edition Date published Revised contents
01 Apr., 1998
Specification No.: C141-F028-**EN
The contents of this manual is subject to
change without prior notice.
All Rights Reserved.
Copyright 1998 FUJITSU LIMITED
This page is intentionally left blank.
C141-F028-01EN iii
FOR SAFE OPERATION
Handling of This manual
This manual contains important information for using this product. Read thoroughly before
using the product. Use this product only after thoroughly reading and understanding
especially the section “Important Alert Items” in this manual. Keep this manual handy, and
keep it carefully.
FUJITSU makes every effort to prevent users and bystanders from being injured or from
suffering damage to their property. Use the product according to this manual.
Functional Limitations
There may be certain functional limitations concerning the specifications and functions of the
products covered by this manual depending on the equipment version, especially concerning
the following functions.
Versions in which there functions can be used will be communicated through
“ENGINEERING CHANGE REQUEST/NOTICE”, issued by Fujitsu.
Function Equipment Version Which Supports These Functions
Equipment
Version No. EPROM
Version No. Standard INQUIRY Data Product
Revision (ASCII)
READ RAM Command
WRITE RAM Command These commands cannot be used in the current version.
(Proceed to the Copyright Page)
iv C141-F028-01EN
Related Standards
Specifications and functions of products covered by this manual comply with the following
standards.
Standard (Text) No. Name Enacting Organization
NCITS TR-9 FIBRE CHANNEL PRIVATE LOOP
SCSI DIRECT ATTACH (FC-PLDA) American National
Standards Institute
(ANSI)
ANSI X3.230-1994 FIBRE CHANNEL PHYSICAL AND
SIGNALING INTERFACE (FC-PH) American National
Standards Institute
(ANSI)
ANSI X3.297-1996 FIBRE CHANNEL PHYSICAL AND
SIGNALING INTERFACE-2 (FC-PH-
2)
American National
Standards Institute
(ANSI)
ANSI X3.272-199X FIBRE CHANNEL ARBITRATED
LOOP (FC-AL) American National
Standards Institute
(ANSI)
ANSI X3.269-199X FIBRE CHANNEL PROTOCOL FOR
SCSI (SCSI-FCP) American National
Standards Institute
(ANSI)
All Right Reserved, Copyright © 1998 Fujitsu, Limited
C141-F028-01EN v
PREFACE
This manual explains concerning the MAA3182FC (hereafter, MAA31xxFC), MAB3091FC and
MAB3045FC (hereafter, MAB30xxFC), MAC3091FC and MAC3045FC (hereafter, MAC30xxFC) series of
3.5 inch hard disk drives with built-in SCSI controller.
This manual gives detailed explanations of device configuration, fault analysis, parts replacement,
operation check, adjustment, and hardware operation principles for the disk drives.
This manual is for engineers who have used fixed-type magnetic disk drives and are familiar with the
operation environment of magnetic disk drives in user systems.
For the organization of manuals related to these disk drives and the scope of descriptions in this manual, see
the "Manual system" described later. A full understanding on the contents of all volumes of the OEM
manuals is assumed. (The OEM manuals have volumes covering product specification and installation
procedure, interface specifications, and command processing functions and command specifications).
This manual is organized as follows:
This manual consists of the 5 chapters shown below, a Glossary and a list of Abbreviations.
CHAPTER 1 SPECIFICATIONS AND EQUIPMENT CONFIGURATION
This chapter explains concerning the basic specifications, the basic configuration, interface connector, setting
switches and setting plug of the MAA31xxFC, MAB30xxFC and MAC30xxFC series disk drives.
CHAPTER 2 MAINTENANCE AND DIAGNOSIS
This chapter describes the basic requirements for maintenance of the MAA31xxFC, MAB30xxFC and
MAC30xxFC series disk drives. This chapter also describes diagnostic methods for operation check
and the basics of troubleshooting the disk drives.
CHAPTER 3 FAULT ANALYSIS
This chapter describes how to collect fault analysis information and how to analyze the collected information.
CHAPTER 4 REMOVING AND REPLACING PARTS
This chapter describes how to remove and replace parts that can be replaced in the field.
CHAPTER 5 OPERATION PRINCIPLES
This chapter describes the hardware configuration and operation of the MAA31xxFC, MAB30xxFC and
MAC30xxFC series disk drives.
Glossary
Abbreviations
vi C141-F028-01EN
CONVENTIONS
This manual uses the following conventions for alerts to prevent physical or property damages to users
or by standards.
DANGER
DANGER indicates that personal injury will occur if the user does not perform the procedure
correctly.
WARNING
WARNING indicates that personal injury could occur if the user does not perform the procedure
correctly.
CAUTION
CAUTION indicates that either minor or moderate personal injury may occur if the user does not
perform the procedure correctly.
NOTICE
NOTICE indicates that inconvenience to the user such as damages to the product, equipment, data,
and/or other property may occur if the user does not pay attention or perform the procedure correctly.
IMPORTANT
IMPORTANT indicates information that the helps the user use the product more effectively.
Indicates
This manual indicates;
Decimal number: Indicates as it is.
Hexadecimal number: Indicates as X’17B9’, 17B9h, or 17B9H
Binary number: Indicates as “010”
C141-F028-01EN vii
DISCLAIMER
Failure of the MAA31xxFC, MAB30xxFC and MAC30xxFC series intelligent disk drive is defined as
a failure requiring adjustments, repairs, or replacement. Fujitsu is not responsible for drive failures
caused by misuse by the user, poor environmental conditions, power trouble, host problems, cable
failures, or any failure not caused by the drive itself.
The suffix of the model name of the disk drive varies depending on the electrical requirements,
capacity, and data format at factory shipment of the SCSI, i.e., the interface for connecting the three
device types or host system and the disk drives (Note 1). However, in this manual, the typical model
names (Note 2) are used unless otherwise noted. These disk drives may be called intelligent disk
drives (IDD), drives, or devices in this manual.
Note 1: Model names
MAA3182FC
Interface types FC: Fibre Channel
Memory capacity (100 MB units)
Disk size 3: 3.5 inch
Type AA: 1.6-inch height (7,200 rpm)
AB: 1-inch height (7,200 rpm)
AC: 1-inch height (10,033 rpm)
Note 2: Type model name
Type model name Model name
MAA3182 MAA3182FC
MAB3091 MAB3091FC
MAB3045 MAB3045FC
MAC3091 MAC3091FC
MAC3045 MAC3045FC
This page is intentionally left blank.
C141-F028-01EN ix
Cautions Regarding Safety
List of Items with Serious Warnings
Serious warnings included in this manual are as follows.
CAUTION Indicates items for which, if the product is not used correctly, there is danger not
only of minor or mildly severe injury, but also danger of the product itself being
damaged or of other users and their property being injured or damaged.
Work Category Warning Item Page
During Storage Injury
1. To avoid shocks, turn off the power before mounting or
removing a PCA, and before connecting or disconnecting a
cable, connector, or plug.
2. To avoid injury, do not touch the mechanical assembly during
disk drive operation.
3. Do not use solvents to clean the disk drive.
2-1
Injury
To prevent injury to workers, note the cautions listed in
Subsection 2.1.1. 4-3
During Assembly,
Maintenance Damage to the Equipment
1. To discharge static electricity from the human body, touch the
frame (grounding) before touching a PCA. This prevents the
PCA from being damaged by static electricity.
2. To prevent electrical damage to the disk drive, turn the power
off before mounting or removing a PCA or connecting or
disconnecting a cable, connector, or plug.
3. Do not turn the power on while removing a PCA. This
operation is required to prevent unexpected or unpredictable
operation.
4. Do not use a conductive cleaner to clean a disk drive
assembly.
5. Open all ventilation holes to prevent overheating of electric
circuits.
6. Ribbon cables are marked with a colored line. Connect the
ribbon cable to a cable connector with the colored wire
connected to pin 1.
2-2
Este manual sirve para los siguientes modelos
4
Tabla de contenidos
Otros manuales de Almacenamiento de Fujitsu
Fujitsu
Fujitsu MHZ2080BJ Manual de usuario
Fujitsu
Fujitsu MAF3364FC SERIES Manual de usuario
Fujitsu
Fujitsu MHV2040AH - Mobile - Hard Drive Manual de usuario
Fujitsu
Fujitsu AIRSTAGE UTY-ASGXZ1 Manual de usuario
Fujitsu
Fujitsu ETERNUS LT140 Manual de usuario
Fujitsu
Fujitsu GP5-HDH461 Manual de usuario
Fujitsu
Fujitsu ETERNUS LT20 S2 Manual de usuario
Fujitsu
Fujitsu MAH3182MC SERIES Manual de usuario
Fujitsu
Fujitsu MPE3XXXAE Manual de usuario
Fujitsu
Fujitsu MAW3073 SERIES Manual de usuario
Fujitsu
Fujitsu ETERNUS DX60 S3 Manual de usuario
Fujitsu
Fujitsu ETERNUS DX Disk Manual de usuario
Fujitsu
Fujitsu ETERNUS DX S5 Series Manual de usuario
Fujitsu
Fujitsu MHG2102AT - Mobile 10 GB Hard Drive Manual de usuario
Fujitsu
Fujitsu ETERNUS DX S4 Series Manual de usuario
Fujitsu
Fujitsu PG-HDH97A Manual de usuario
Fujitsu
Fujitsu MPD3XXXAT Manual de usuario
Fujitsu
Fujitsu MAP3147FC Manual de usuario
Fujitsu
Fujitsu C141-E090-02EN Manual de usuario
Fujitsu
Fujitsu MHW2040BS Manual de usuario
Manuales populares de Almacenamiento de otras marcas
Spectra Logic
Spectra Logic T-Series Spectra T50e Manual de usuario
Panasonic
Panasonic LKM-F931-1 Manual de usuario
Tabernus
Tabernus Enterprise Erase E2400 Manual de usuario
Rocstor
Rocstor COMMANDER 3F series Manual de usuario
HP
HP P9000 Manual de usuario
Western Digital
Western Digital Ultrastar Data60 Manual de usuario