Fujitsu PRIMERGY TX150 S6 Guía

CA92276-8243-01

Note on using PRIMERGY TX150 S6

Thank you for purchasing our product. Before you start using your server, please

carefully read the additional notes described below.

June 2008

FUJITSU LIMITED

1．Warning Messages of ServerView Remote Connector when start up the OS

[Symptom]

If following all conditions are met, the warning message below would be recorded on Application

Event Log when start up the server.

Type: Warning

Source:ServerView Remote Connector

Event ID: 0

Description:

Initialization not completed timely (0 seconds)

[Conditions]

1) ServerView Agent for Windows is installed

2) The system is highly-loaded for start up

[Cause]

Because the system is highly-loaded for start up, initializing process of ServerView Remote

Connector is delayed. This warning is to notify the service start up is not completed while certain

period of time. This message is not for failure notice of service start up.

[Remedy]

Even if the message is recorded because of the process delay as above, the service keeps running

the initializing process. The service will automatically start after complete the initializing process

of ServerView Remote Connector. No special handling is required.

* ServerView Remote Connector service is used as the service at the Performance Manager of ServerView.

Even though this service is not active, there is no effect to the function other than Performance Manager.

Note: how to confirm

Please follow the steps below to confirm ServerView Remote Connector service runs normally.

－ Start the Performance Manager from the ServerView S2.

－ Select the server of which you want to confirm the performance from the left side frame.

－ Select the <Report View> tab.

－ Select any report, and click the” Show >>” button.

If the graphics is displayed, ServerView Remote Connector service runs normally. Please use it without

any change. If the service is not a normal run, the dialog box as below will be displayed.

1／8

Note: It is necessary to set the report setting beforehand.

For direction of Performance Manager, please refer to "ServerView User's Guide".

If the ServerView Remote Connector is not a normal run, please reboot the service with following

process. (There is no necessity to reboot the system.)

[Control Panel] - [Administrative Tools] - [Services] - [ServerView Remote Connector]

Do <Restart> the service

2． Updates for "PRIMERGY TX150 S6 User's Guide"

Chapter 4 "4.3 Storing the System Configuration Information"

4.3.1 Storing the BIOS Information and the Remote Management Controller Information (Page 82)

Deletion Please delete following notes.

 Do not input the file extension at the end of a file name.

 The file name is given as "cmosfile" when a file name is not input.

4.3.2Recovering the BIOS / Remote Management Information (Page 83 - 84)

Correction There is a misspelling on the command line.

4 Enter the following command and press the [Enter] key.

False: A:¥SMT>BIOSRESET.bat

True: A:¥SMT>BIOSREST.bat

Deletion Please delete following notes.

 Do not input the file extension at the end of a file name.

 The file name is given as "cmosfile" when a file name is not input.

4.3.2 Recovering the BIOS / Remote Management Information (Page 83)

Deletion Please delete following misdescription.

Server Management Tools disk is required to be created when mentioned as empty "blank" on the label of the "Server

Management Tools" disk, supplied with the server. Create Server Management Tools by referring to "4.4 Creating

Maintenance Tools and Driver Disks" (pg.85).

2／8

Chapter 6 "6.2 Removing and Attaching Covers"

6.2.1 Removing Covers

■Attaching covers (Page 116)

Addition Following caution notes are added for attaching the cover description.

Before attaching the covers, flip the front cover and make sure the position of the key lock part (Point A) is

settled at the

proper position

. If the key lock part is not at the

proper position

, resetting the part before

attaching the covers are required. It may cause a breakage failure if you attach the covers and lock the key

with wrong position.

back side the front covers

3／8

Close-up of point A

Point Ａ

Improper Position

Key lock part is unhooked (yellow circle).

Proper Position

Key lock part is hooked.

4／8

Chapter 6 "6.6 Installing 5-inch Internal Options"

6.6.2 Installable 5-inch Internal Devices (Page 136)

Correction Please correct the list of installable 5-inch internal devices by adding 2 units.

False:

Unit type Product name Product ID Cable (separate) SCSI ID

Internal DAT72 unit Tape Drv DAT72 36GB internal PG-DT5041 －－

Internal LTO3 unit Tape Drv LTO3 Ultrium3/ Ultrium2

400GB PG-LT302 PG-CBLS027 5

True:

Unit type Product name Product ID Cable (separate) SCSI ID

Internal DAT72 unit Tape Drv DAT72 36GB internal PG-DT5041 －－

Internal LTO unit Tape Drv LTO Ultrium1 100GB PG-LT102 PG-CBLS027 5

Internal LTO2 unit Tape Drv LTO2 Ultrium2 200GB PG-LT201 PG-CBLS027 5

Internal LTO3 unit Tape Drv LTO3 Ultrium3/ Ultrium2

400GB PG-LT302 PG-CBLS027 5

6.9 Connecting External SCSI Devices (Page 146)

Correction There are misdescription about the product ID and length of cables.

Connecting Backup Cabinet

False: PG-CBLS001（1.5m）

PG-CBLS002（5m）

True: PG-CBLS007 (1.8m)

PG-CBLS008 (5m)

7.2.7 Advanced Processor Options submenu (Page.158)

Correction Please correct the following table for BIOS settings.

False)

table: Items on the Advanced Processor Options submenu

Item Setting Description

Enhanced SpeedStep Disabled（Unchangeable） Sets whether to enable or disable the power saving

function.

Enhanced Idle Power State Disabled（Unchangeable） Configures the CPU internal setting. This item is

displayed only when Xeon 3065/3085 processor is

onboard.

Virtualization Technology ・Disabled（Initial value）

・Enabled

Sets whether to enable or disable Virtualization

Technology.

True)

table: Items on the Advanced Processor Options submenu

Item Setting Description

Enhanced SpeedStep ・Disabled(Initial value)

・Enabled

Sets whether to enable or disable the power saving

function.

This item is changeable only when Windows system is

installed.

Enhanced Idle Power State Disabled（Unchangeable） Configures the CPU internal setting. This item is

displayed only when Xeon 3065 / 3085 / X3320 /

E3110 / Core2Duo E4600 processor is onboard.

Virtualization Technology ・Disabled（Initial value）

・Enabled

Sets whether to enable or disable Virtualization

Technology. This item is displayed only when Xeon

3065 / 3085 / X3210 / X3320/ E3110 processor is

onboard.

5／8

7.2.9 Security Menu (Page. 160)

Correction

False)

True)

7.2.9 Security Menu(Page 161)

Addition

table: Items on the Security menu

Item Setting Description

・・・

System Password Lock ・Standard（Initial value）

・WOL SKIP

Sets whether to enter a password or not when

turn on by Wakeup On LAN.

TPM (Security Chip)

Setting

Configures the TPM (Security Chip) settings.

Press the [Enter] key to display the TPM(Security Chip) Setting submenu.

Virus Warning Disabled（Unchangeable） Sets whether or not to check the boot sector of the

hard disk drive after the previous system startup.

If the boot sector is changed without a clear

reason, it is necessary to scan the system for

computer viruses with a virus detection program.

・・・

table: Items on the TPM(Security Chip) Setting submenu

Item Setting Description

Security Chip ・Disabled（Unchangeable）

・Enabled

Configure the Security Chip setting..

Current TPM State Display the current TPM State.

Change TPM State

・No Change（Initial value）

・Enable&Activate

・Disable&Deactivate

・Clear

Change the TPM State. This item is displayed only

when Security Chip setting is enabled.

7.2.15 Console Redirection Submenu (Page 166)

Correction

False)

table: Items on the Console Redirection submenu

Item Setting Description

Console Redirection ・Disabled (Initial value)

・On-board COM A

・On-board COM B

Sets whether to enable or disable console redirection.

When set to [On-board COM A] or [On-board COM

B], the following parameters appear. Set each

parameter.

True)

table: Items on the Console Redirection submenu

Item Setting Description

Com Port Address ・Disabled (Initial value)

・On-board COM A

・On-board COM B

Sets whether to enable or disable console redirection.

When set to [On-board COM A] or [On-board COM

B], the following parameters appear. Set each

parameter.

6／8

Appendix A Server Specifications (Page 204)

A.1 SAS Model (Page 204)

Correction

False)

True) table: Server specifications-SAS Model

Item Functions and specifications

Product name PRIMERGY TX150 S6 SAS model

Product ID PGUT1564A

Chipset Intel 3210/ICH9R®

Intel® CoreTM 2

Duo Processor Dual Core Intel® Xeon Processor

Type E4600

(2.40GHz)

3065

(2.33GHz)

E3100

(3GHz)

X3220

(2.40GHz)

X3320

(2.50GHz)

Number of cores 2 4

L2 Cache Size 2MB 4MB 6MB 2x4MB 6MB

FSB 800MHz 1333MHz 1066MHz 1333MHz

CPU

Number of CPUs Standard :1(Maximum:1)

Security chip Complied with TCG 1.2

■ Supported OS（Page 205）

Addition

The supported operating systems for this server are as below.

• Windows Server 2003, Standard Edition (SP2 or later)

• Windows Server 2003, Standard x 64 Edition (SP2 or later)

• Windows Server 2003 R2, Standard Edition (SP2 or later)

• Windows Server 2003 R2, Standard x64 Edition (SP2 or later)

• Windows Small Business Server 2003 R2 (SP2 or later)

• Windows Small Business Server 2003 (SP2 or later)

• Windows Server 2008 Standard (32-bit)

• Windows Server 2008 Standard (64-bit)

• Red Hat Enterprise Linux ES (v.4 for x86)

• Red Hat Enterprise Linux ES (v.4 for EM64T)

• Red Hat Enterprise Linux 5 (for x86)

• Red Hat Enterprise Linux 5 (for Intel64)

For details of Windows Server 2008, refer to the "Support Matrix" at the following URL:

http://www.fujitsu.com/downloads/PRMRGY/support-matrix.pdf

7／8

A.1 SAS Model (Page 206)

Correction

False)

True) table: Server specifications-SATA Model

Item Functions and specifications

Product name PRIMERGY TX150 S6 SATA model

Product ID PGUT1564B

Chipset Intel 3210/ICH9R®

Intel® CoreTM 2

Duo Processor Dual Core Intel® Xeon Processor

Type E4600

(2.40GHz)

3065

(2.33GHz)

E3100

(3GHz)

X3220

(2.40GHz)

X3320

(2.50GHz)

Number of cores 2 4

L2 Cache Size 2MB 4MB 6MB 2x4MB 6MB

FSB 800MHz 1333MHz 1066MHz 1333MHz

CPU

Number of CPUs Standard :1(Maximum:1)

Security chip Complied with TCG 1.2

■ Supported OS（Page 207）

Addition

The supported operating systems for this server are as below.

• Windows Server 2003, Standard Edition (SP2 or later)

• Windows Server 2003, Standard x 64 Edition (SP2 or later)

• Windows Server 2003 R2, Standard Edition (SP2 or later)

• Windows Server 2003 R2, Standard x64 Edition (SP2 or later)

• Windows Small Business Server 2003 R2 (SP2 or later)

• Windows Small Business Server 2003 (SP2 or later)

• Windows Server 2008 Standard (32-bit)

• Windows Server 2008 Standard (64-bit)

• Red Hat Enterprise Linux ES (v.4 for x86)

• Red Hat Enterprise Linux ES (v.4 for EM64T)

• Red Hat Enterprise Linux 5 (for x86)

• Red Hat Enterprise Linux 5 (for Intel64)

For details of Windows Server 2008, refer to the "Support Matrix" at the following URL:

http://www.fujitsu.com/downloads/PRMRGY/support-matrix.pdf

8／8

Otros manuales para PRIMERGY TX150 S6

Tabla de contenidos

Otros manuales de Servidor de Fujitsu

Fujitsu

Fujitsu PRIMERGY RX2510 M2 Manual de usuario

Fujitsu

Fujitsu PRIMERGY TX200 S7 Manual de usuario

Fujitsu

Fujitsu PRIMERGY RX330 S1 Manual de usuario

Fujitsu

Fujitsu PRIMERGY RX2520 M1 Manual de usuario

Fujitsu

Fujitsu PRIMERGY BX620 S5 Manual de usuario

Fujitsu

Fujitsu PRIMERGY CX122 S1 Manual del propietario

Fujitsu

Fujitsu PRIMERGY Manual de usuario

Fujitsu

Fujitsu PRIMERGY MX130 S2 Upgrade and maintenance... Manual de usuario

Fujitsu

Fujitsu PRIMERGY BX922 S2 Manual de usuario

Fujitsu

Fujitsu PRIMERGY RX200 S3 Manual del propietario

Fujitsu

Fujitsu PRIMERGY RX1330 M3 Manual de usuario

Fujitsu

Fujitsu SPARC Enterprise T5440 Server Manual técnico

Fujitsu

Fujitsu Primergy RX100 S2 Manual de usuario

Fujitsu

Fujitsu SPARC Enterprise T5120 Manual técnico

Fujitsu

Fujitsu Primergy RX300 S2 Guía

Fujitsu

Fujitsu PRIMERGY TX1320 M4 Manual de usuario

Fujitsu

Fujitsu PRIMERGY BX924 S3 Manual de usuario

Fujitsu

Fujitsu PRIMEQUEST 1000 Series Manual de usuario

Fujitsu

Fujitsu PRIMERGY RX1330 M5 Manual de usuario

Fujitsu

Fujitsu PRIMERGY TX300 S6 Manual de usuario

Fujitsu

Fujitsu PRIMERGY BX920 S1 Manual de usuario

Fujitsu

Fujitsu PRIMERGY RX300 S6 Manual de usuario

Fujitsu

Fujitsu S120 Series Manual de usuario

Fujitsu

Fujitsu Primergy TX300 S4 Manual de usuario

Manuales populares de Servidor de otras marcas

HP AlphaServer ES47 Manual de usuario

Dell

Dell PowerEdge R410 Manual de usuario

PowerNAS

PowerNAS CMA Manual de usuario

Supero

Supero FatTwin F617R3-FT Manual de usuario

MSI

MSI P1-109N-L70 Manual de usuario

Dell

Dell PowerEdge XE9640 Manual

Dell

Dell PS4100 Instrucciones de montaje

EtroVISION

EtroVISION EV3151 Manual de usuario

NEC

NEC Express5800/T110j Manual de usuario

HP ProLiant Gen9 Manual de usuario

Compaq

Compaq ProLiant 3000 Manual

Dell

Dell PowerEdge 3YPMN Manual de usuario

iRobo

iRobo IPC2U Manual de usuario

Nortel

Nortel 1000 Con?guration guide Manual de usuario

Asus

Asus AP7500 Manual de operación y mantenimiento

Avid Technology

Avid Technology AirSpeed 5000 Manual de usuario

HP Integrity rx2600 Guía de instalación

Milestone

Milestone Husky IVO 350T Manual de usuario