Fujitsu FTP-622MCL301 Manual de usuario
NOT FOR NEW
DESIGN
FTP-622MCL301/302
■OVERVIEW
FTP-622MCL/FTP-622DCL/DSL Series is an ultra high speed line
thermal printer driven by 24 VDC, printing on 2-inch wide paper
(58 mm/60 mm).
This printer is compact and light weight, and the design allows
easy head maintenance, easy head cleaning and easy head
replacement.
This printer is suitable for a variety of applications, such as POS
terminals, ticket machines, coupon machines, label printers,
medical instruments, etc. A printer with a specially designed cutter
is also available.
■HIGHLIGHTS
• Ultra high speed printing
It can print at 80 mm/s (640 dotlines/s) maximum by using
Fujitsu Components' unique head drive control.
• Compact and lightweight
This printer has a low profile of only 20 mm, and a light weight
of approximately 81 g.
• Low power consumption
The peak current for head driving is approximately 2.3 A (at 80
mm/s printing speed, 50% printing ratio).
• Easy head access
It is designed for easy head cleaning and head replacement.
• Paper auto loading function
Thermal paper can be loaded without head-up lever operation.
• ESC/POSTM*1 Commands
The commands conform to ESC/POSTM.
• Auto Cutter
Printer with auto cutter (full cut/partial cut) is also available.
• UL Recognized
File No.E171434
*1 ESC/POSTM is a registered trademark of SEIKO EPSON Corp.
24V DRIVE, ULTRA HIGH SPEED LINE THERMAL PRINTER
2” MECHANISM, WITH CUTTER
FTP-622MCL301
FTP-622DCL011
FTP-622CU101
1
2
FTP-622MCL301/302
NOT FOR NEW
DESIGN
Part number FTP-622MCL301/302
Printing method Thermal-sensitive line dot method
Dot structure 448 dots/line
Dot pitch (Horizontal) 0.125 mm (8 dots/mm)—Dot density
Dot pitch (Vertical) 0.125 mm (8 dots/mm)—Line feed pitch
Effective printing area 56 mm
MCL301 58 mm
Paper width MCL302 60 mm
Paper thickness 60~100 µm*1
Cutting type full or partial
Number of columns 37 columns/line (24×12 dot font)
Maximum printing speed 640 dotlines/s (80 mm/s)
Alphanumeric KANA: 159 International characters: 195
Character types JIS KANJI (FTP-622DCL101/111): approximately 6800
24 ×12 dots, (3.0 ×1.5 mm), 37 columns
24 ×24 dots, (3.0 ×3.0 mm), 18 columns
16 ×8 dots, (2.0 ×1.0 mm), 56 columns
16 ×16 dots, (2.0 ×2.0 mm), 28 columns
■DESIGNATION
Part number
With Auto cutter FTP-622MCL301/302*1
FTP-622DCL011/111*2
FTP-622DSL011/012*3
FTP-622CU101*4
Item
Printer mechanism
Interface board
■GENERAL SPECIFICATIONS
SpecificationsItem
Character composition, dimensions (H×W),
Number of characters
(Continued)
Centronics Standard with Auto cutter
Serial (RS-232C) standard with auto cutter
LSI(MCU)
*1: Constructed with mechanism+cutter+attachment. 301 is for front paper insertion (curl path)
and 302 is for rear paper insertion (straight path).
*2: 011 supports ANK and 101 supports ANK+Kanji.
*3: 012 supports ANK and 111 supports ANK+Kanji, + FLASH memory.
*4: CU101 supports Kanji and cutter control.
3
FTP-622MCL301/302
NOT FOR NEW
DESIGN
Power supply
Dimensions
Part number FTP-622MCL301/302
Interface Centronics (ESC/POSTM), RS232C
24VDC ±5%, Voltage
Current : average*2 ( ): Peak
For head 0.87 (1.16) A (at 80 mm/s printing speed, 25% printing ratio)
0.63 (1.16) A (at 50 mm/s printing speed, 25% printing ratio)
0.58 (0.58) A (at 30 mm/s printing speed, 25% printing ratio)
For motor 24VDC ±5%, 1.0 A maximum
For cutter 24VDC ±5%, 1.0 A maximum
For logic 5VDC ±5%, 0.5 A maximum
Mechanism (cutter)
101 (W) ×70 (D) ×42 (H) mm (w/cutter)
Interface board 131 (W) ×89 (D) ×24 (H) mm
Weight (Mechanism+Cutter) approximately 300 g (w/cutter)
Pulse durability : 1 ×108pulse/dot (using Fujitsu's standard
Mechanism driving method)
Expected life Wear resistance: 50 km (at 25% printing ratio)
Cutter 3 ×105cuts
Operating temperature 0 to +50°C*3
Operating humidity 20 to 85% RH (no condensation)
Storage temperature –20 to +60°C (excluding paper)
Storage humidity 5 to 95% RH (no condensation)
Head temperature By thermistor (applied energy control, abnormal temperature detection)
Detection Paper out/Mark detect By photointerrupter
Head-up By microswitch
For front insertion use (58 mm width) : FTP-020PU001,FTP-020P0701
For rear insertion use (60 mm width) : FTP-020P0020,FTP-020P0702
*Recommended papers
· Oji Paper : PD150R,PD160R,PD170R
· NIPPON Paper : TF50KS-E,TF60KS-E,TF60KJ-R
· MITSUBISHI Paper Mills : P220VBB-1,AFP-235
SpecificationsItem
(Continued)
Environmental
conditions
Recommended thermal sensitive paper
*1: There may be exceptions.
*2: 24VDC, minimum head resistance.
*3: Guarantee: +5°C ~+40°C.
4
FTP-622MCL301/302
NOT FOR NEW
DESIGN
MCL301
MCL302
3-M3 FIXING HOLE FROM UPPER SIDE
2-M 3 burring (FIXING HOLE FROM BOTTOM SIDE)
235±15
14.242
67.7
±1
(70.8)
(78.6)
58.4(POSITIONINGHOLE)
45.0
(97.3)
(49.5) 47.8
±1
13.3 38.5
3—2.0 or less
300±15
Note: all dimensions are nominal value.
(2 or less)
(47.2)
PAPER
INSERTION
PAPER
INSERTION
2 or less
Unit: mm
Mechanism with cutter
5
FTP-622MCL301/302
NOT FOR NEW
DESIGN
■INTERFACE, COMMAND, OPTIONS
Interface board
Unit: mm
■FUNCTION
ITEM ITEM
1. Test printing 8. Cutter trouble detection
2. Paper-out detection 9. Motor power save
3. Paper near end detection 10. Mark detection
4. Head-up detection 11. MCU trouble detection
5. Abnormal temp. of thermal head detection 12. Power on/off sequence protection
6. Blown fuse detection 13. Motor protection
7. Abnormal voltage detection of head 14. Hardware timer
Please refer to the FTP-622DCL DATA SHEET and the FTP-622DSL DATA SHEET for Interface, Command, and
Options.
88.9
78.7
39.4
39.4
5.1
5.1 5.1
5.1 5.1
5.1
5.1
5.1
120.7
105.4
120.7
116.8
87.6
19.1
130.8
43.2 86.4
CN10
CN5CN2** CN3
CN1
CN8
CN13CN11*
*CN11 on FTP-622DCL011/111 & 622DSL011/012/112 only
**CN2 on FTP-622DSL only
4—ø3.6
6
FTP-622MCL301/302
NOT FOR NEW
DESIGN
© 2001 Fujitsu Components America, Inc. All company and product names are trademarks or registered
trademarks of their respective owners. Rev. 09/2001
Japan
Fujitsu Component Limited
Gotanda-Chuo Building
3-5, Higashigotanda 2-chome, Shinagawa-ku
Tokyo 141, Japan
Tel: (81-3) 5449-7010
Fax: (81-3) 5449-2626
Email: [email protected]
Web: www.fcl.fujitsu.com
North and South America
Fujitsu Components America, Inc.
250 E. Caribbean Drive
Sunnyvale, CA 94089 U.S.A.
Tel: (1-408) 745-4900
Fax: (1-408) 745-4970
Email: [email protected]
Web: www.fcai.fujitsu.com
Europe
Fujitsu Components Europe B.V.
Diamantlaan 25
2132 WV Hoofddorp
Netherlands
Tel: (31-23) 5560910
Fax: (31-23) 5560950
Email: [email protected]
Web: www.fceu.fujitsu.com
Asia Pacific
Fujitsu ComponentsAsia Ltd.
102E Pasir Panjang Road
#04-01 Citilink Warehouse Complex
Singapore 118529
Tel: (65) 375-8560
Fax: (65) 273-3021
Email: [email protected]
www.fcal.fujitsu.com
Fujitsu Components
International
Headquarter
Offices
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Impresora de Fujitsu
Fujitsu
Fujitsu Impact 4550 PRO Manual de usuario
Fujitsu
Fujitsu 628WSL110H2 Manual de usuario
Fujitsu
Fujitsu FTP-627USL431 Manual de usuario
Fujitsu
Fujitsu DL7400 Manual de usuario
Fujitsu
Fujitsu FP-510II Manual de usuario
Fujitsu
Fujitsu fi-748PRB Manual
Fujitsu
Fujitsu ScanSnap iX100 Manual de instrucciones
Fujitsu
Fujitsu FTP-629DCL014R Manual de usuario
Fujitsu
Fujitsu DX2300 Manual de usuario
Fujitsu
Fujitsu DPMG9 Manual de usuario
Fujitsu
Fujitsu DL-3750+ Manual de usuario
Fujitsu
Fujitsu RX7300 Manual de usuario
Fujitsu
Fujitsu DL7400Pro Manual de usuario
Fujitsu
Fujitsu PrintPartner 16V Manual de usuario
Fujitsu
Fujitsu DL2400 Manual de usuario
Fujitsu
Fujitsu PrintPartner 20W Manual de usuario
Fujitsu
Fujitsu 9811 ATB Manual
Fujitsu
Fujitsu FP-1000 Manual de usuario
Fujitsu
Fujitsu DL-6400 Manual de usuario
Fujitsu
Fujitsu N7100E Manual de usuario
