Fujitsu P2711 TE QHD Instrucciones de instalación

Page 1 of 14

Disassembly and Repair 2

Information on the installation and removal of components 3

Tools 4

Disassembly 5

P2711 TE/TS QHD Monitor Exploded Drawing 10

P2711 TS CAM Monitor Exploded Drawing 11

Replaceable Components and Services 12

Disposal information for recycling companies 13

Disassembly and repairs

Display P2711 TE QHD

Display P2711 TS QHD

Display P2711 TS

CAM

Version date 12.01.2023

Category Disassembly and repairs

Contents

Page 2 of 14

Disassembly and Repair

We recommend printing out the relevant sections of this chapter prior to installation

as the device for installing/removing hardware components needs to be switched off.

In order to repair the display, please follow the disassembly instructions to remove the defect part, replace it with spare part, then follow the

instructions in reverse order.

If you have received any further documents with your device, you should read these through carefully.

Please note the following instructions before installing/removing system components:

■ The device must be switched off when installing/removing components and it must

not be in power-saving mode.

■ Disconnect the mains plug before opening the device.

■ After unplugging the mains plug, discharge the remaining voltage by pressing the

activation button.

■ Remove all externally connected cables.

■ Take care not to flex foil cablech any cables when installing/removing components.

■ Please ensure that the installed components that might heat up intensely during

operation do not exceed the permitted operating temperature.

Page 3 of 14

Information on the installation and removal of components

Please pay attention to the locking mechanism (indentations and centring flex foil cables) when installing hardware components.

Note that some components on the mainboard may be very hot if the device was in use shortly before the case was removed.

Utmost care is required during installation and removal to avoid damaging components.

Never use items with sharp edges (screwdrivers) to lever them out.

Parts with Electrostatic Sensitive Devices (ESD) can be identified by a corresponding label.

When dealing with boards with ESDs, the following points must always be observed:

■ Always ensure there is a static discharge (e.g. by touching a grounded object) prior to commencing

with the work.

■ The devices and tools being used must not be statically charged.

■ Only touch the components along the edges or on the areas marked in green (contact points).

■ Contacts and electronic components must not touch when handling components equipped with ESD

protection.

Page 4 of 14

Tools

Screwdriver: Pozidriv PZ 2

Screwdriver: Phillips PH 1

Hexagon Screwdriver size 5

Flat Head Screwdriver

Page 5 of 14

Disassembly

Step Figure Description

Remove the

Stand Base

Ass'y.

Remove the

screws to

remove the

stand base

assy.

Remove the

rear cover

Remove the

rear cover

Disconnect

the flex foil

cable.

Disconnect the

flex foil cable

to remove the

rear cover.

Page 6 of 14

Remove the

tapes and the

flex foil cable

Remove the

tapes and the

flex foil cable

Remove the

screws to

remove the

middle frame

and the panel

Remove the

screws to

remove the

middle frame

and the panel

Take off the

tape and

disconnect

the flex foil

cable

Take off the

tape and

disconnect the

flex foil cable

Page 7 of 14

Remove the

main board

and power

board

Remove the

screws to

remove the

main board and

power board

Remove the

connectors

Remove the

connect flex foil

cables

Remove the

speakers

Remove the

speakers

Page 8 of 14

The panel

The WEBCAM

Remove the

screws to

remove the

WEBCAM

The key board

Remove the

screws to

remove the key

board

Page 9 of 14

The middle

frame

The middle

frame

The USB

board

Remove the

screw to

remove the

USB board.

The Rear

Cover

The Rear

Cover

Page 10 of 14

P2711 TE/TS QHD/CAM Monitor Exploded Drawing

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Monitor de Fujitsu

Fujitsu

Fujitsu B22-8 TE PRO Manual de usuario

Fujitsu

Fujitsu E22T-7 LED Manual de usuario

Fujitsu

Fujitsu P24W-6 IPS Manual de usuario

Fujitsu

Fujitsu P24W-5 ECO Manual de usuario

Fujitsu

Fujitsu B24W-7 LED Manual de usuario

Fujitsu

Fujitsu P27T-6 IPS Manual de usuario

Fujitsu

Fujitsu P27-9TQ Manual de usuario

Fujitsu

Fujitsu B22T-7 Pro Manual de usuario

Fujitsu

Fujitsu MCM1514V Manual de usuario

Fujitsu

Fujitsu B17-5 ECO Manual de usuario

Fujitsu

Fujitsu Plasmavision P42HTS51E Manual de usuario

Fujitsu

Fujitsu B24W-6 LED Manual de usuario

Fujitsu

Fujitsu B22W-7 Manual de usuario

Fujitsu

Fujitsu B32-9 TS UHD Manual de usuario

Fujitsu

Fujitsu Plasmavision P42HHS10W Manual de usuario

Fujitsu

Fujitsu 4312 FA Manual de usuario

Fujitsu

Fujitsu SCALEOVIEW S17-2 Manual de usuario

Fujitsu

Fujitsu L21T-1 Manual de usuario

Fujitsu

Fujitsu SCALEOVIEW Q26W-1 Manual de usuario

Fujitsu

Fujitsu 280X1024@75Hz Manual de usuario

Fujitsu

Fujitsu Plasmavision P42VHA10W Manual de usuario

Fujitsu

Fujitsu FSC B17-1 Manual de usuario

Fujitsu

Fujitsu P24-8 TE Pro Manual de usuario

Fujitsu

Fujitsu P27T-6P IPS Manual de usuario

Manuales populares de Monitor de otras marcas

Linear Acoustic

Linear Acoustic LQ-1000 Manual de usuario

AOC

AOC I2579V Manual de usuario

Gateway

Gateway FPD1520 Manual de usuario

Furuno

Furuno Mu 120c Manual de usuario

Asus

Asus VB171D - 17" LCD Monitor Manual de usuario

Dell

Dell S2230MX Instrucciones de uso

Philips

Philips 107C64 Manual de usuario

Dell

Dell S2409WFP Manual de usuario

EverFocus

EverFocus EN-7517E Manual de usuario

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Manual de usuario

Dell

Dell Precision 7680 Manual de instrucciones

LG 50PM1M - - 50" Plasma Panel Manual de usuario

Bosch

Bosch DDU 9 Manual de usuario

Acer

Acer A231HL Manual de usuario

Philips

Philips 86BDL4152T Manual de usuario

NEC

NEC AccuSync LCD5V Manual de usuario

Emay

Emay SleepO2 Manual de usuario

IBM

IBM 6360 Instrucciones de instalación